How to Fix the Soft Bricked Poco C50?

Bricked phone is a serious problem, as your brick smartphone could be suffering from a soft brick or hard brick problem, and must be dealt with carefully. It is very common to see a brick smartphone these days. If you are wondering what exactly is a bricked phone, here is your answer.

A bricked phone, hard brick or soft brick, is a smartphone which refuses to start or boot all the way up the home/main screen of the Poco C50 device. This issue is observed within most Android phones because users have a tendency to tamper with the Poco C50 device settings, flashing new and customized ROMs and tweaking with the essential files. Playing around with the phone’s internal set-up leads to such errors, worst of them being a brick smartphone. Usually, a bricked phone does not switch on and stays frozen at the Poco C50 device logo, a blank screen or even worse, doesn’t respond to any command, even the power on command.

If you are confused about the soft brick and hard brick problems and looking for solutions to fix your priced phone, then here is all you need to know.

Read on to find out more.

Part 1: What is the difference between soft brick and hard brick?

To begin with, let us understand the basic difference between a soft brick and hard brick issue. Both versions of a bricked phone prevent it from booting but differ in their causes and gravity of the problem.

A soft-brick problem is caused merely by a software error/crash and makes your device switch on automatically every time you manually turn it off. This phenomenon is referred to as Boot Loop. Soft bricked Android phones are not as difficult to fix as the hard bricked Android phones. It is convenient to say that a soft bricked phone only boots up half-way and not fully, whereas a hard bricked device does not switch on at all. A hard brick error is thus caused when the kernel, which is nothing but an interface for the software to communicate with the hardware, is tampered with. A hard bricked phone is not recognized by your PC when plugged in and is a serious problem. It requires troubleshooting techniques and cannot be easily fixed as the soft brick problem.

Hard bricked phones are a rare sight, but the soft brick is very common. Given below are ways to fix a soft brick Android phone. The techniques listed here are the best and the most efficient ways to get your phone back to its normal working conditions without losing your important data or damaging your device or its software.

Part 2: Stuck at the Boot Loop

This is the first sign of a soft bricked Android phone. Boot Loop is nothing but when your phone does not remain switched off and turns itself on automatically, and freezes at the logo screen or blank screen, every time you manually try to power it off.

Stuck at boot loop problem can be fixed by clearing your Cache partitions. These partitions are nothing but storage locations for your modem, kernels, system files, drivers and built-in Apps data.

It is advisable to clear Cache partitions regularly to keep your phone free from such glitches.

Since the phone refuses to boot, Cache can be cleared from entering into the Recovery Mode. Different Android devices have different ways to put it in recovery mode. Normally pressing the power key and volume down key helps, but you may refer to your phone’s guide for better understanding and then follow the steps given below to clear the cache partition:

Once you are the recovery mode screen, you will see a number of options as shown in the screenshot.

Use the volume down key to scroll down and select ”Wipe cache partition” as shown below.

>

After the process is completed, select “Reboot System” which is the first option in the recovery mode screen.

This method will help you erase all the clogged up and unwanted files. You may loose some App related data, but that is a small price to pay to fix your bricked phone.

If this method does not boot up your brick smartphone and the problem still persists, there are two more things you can try. Read ahead to find out about them.

Part 3: Booting straight into recovery mode

If your bricked phone does not boot up to your Home Screen or Lock screen and instead boots directly into Recovery Mode, there is not much left to do. Booting straight into recovery mode is undoubtedly a soft brick error but it also indicates a possible problem with your current ROM. The only option you have to flash a new ROM to reboot your bricked phone back to its normal functioning.

To flash a new ROM:

Firstly, you must root your phone and unlock the Bootloader. Every phone’s mechanism to unlock the bootloader is different, thus, we suggest to refer to your user manual.

Once the Bootloader is unlocked, take a backup of all your data by selecting “Backup” or “Android” back in recovery mode. The process should not take long and all you need to do is tap “OK” to config backup.

In this step, download a ROM of your choice and store it in your SD Card. Insert the SD Card in your phone to begin the flashing process.

Once at the recovery mode, select “Install Zip from SD Card” from the options.

Scroll down using the volume key and use the power key to select the downloaded ROM.

This might take a few minutes of your time, but once the process is complete, reboot your phone.

Hopefully, your bricked phone will not boot normally and work smoothly.

Part 4: Booting straight into Bootloader

If your bricked phone boots straight into Bootloader, then this a serious issue and must not be taken lightly. Flashing a new ROM or clearing cache partitions are of little help in such a brick smartphone situation. Booting straight into Bootloader is a peculiar soft bricked Android phone feature and can be tackled only by downloading and flashing your original ROM from the manufacturer. In order to do so, a detailed study about your manufacturer’s ROM, ways to download and flash must be carried out. Since different Android phones come with different types of ROMs, it difficult to cover all the aspects about the different types of ROMs.

Brick smartphone problem has become more prominent than phone freezing or hanging issue. Android users are often seen looking for solutions to fix their soft brick and hard brick phones. Android phones are prone to get bricked and thus, it is important for us to know about the three techniques given above. These methods have been tried, tested and recommended by ay affected bricked phone users. Therefore, these tips are reliable and worth a try. So if your phone acts stubborn and refuses to boot normally, examine the problem carefully and adopt one of the solutions given above which best suits your situation.

Stuck at Android System Recovery Of Poco C50 ? Fix It Easily

In this article, you will learn what is Android system recovery, and how to fix Android stuck at system recovery step by step. To get out of Android system recovery more easily, you need this Android repair tool.

You know your Poco C50 is stuck in recovery mode when you cannot turn on the Poco C50 device. If you try to turn it on, it shows a message that says, “Android System Recover.” This situation can be quite debilitating for most Android users. Most of the time, you don’t know whether you have lost all of your important Android data. It is even more worrying because of the fact that you cannot turn on your device at all, especially when you don’t know how to fix it.

Part 1. What is Android System Recovery?

Despite all the worry that surrounds an unwanted Android system recovery screen, it is actually a feature that can be quite helpful to your Poco C50 when it’s needed. It can be useful when you want to hard reset the Android device without having to access the settings. This can be very useful if your device is not working very well or if your touch screen is experiencing problems. It can also be very helpful when you are having a problem accessing the settings on your device.

For these reasons, it is actually a good thing, although when it does happen unexpectedly, you may want to know how to fix it.

Part 2. How to get to Android System recovery

Now that you know how useful the Android System can be, you may want to know how to utilize this feature to get out of some of the problems we mentioned above. Here’s how you can safely get to the Android recovery system on your Poco C50.

Step 1: Hold down the power key and then select “Power Off” from the options on the screen. If, however, your screen is unresponsive, keep holding the power key for several seconds until the Poco C50 device is completely turned off.

Step 2: Next, you need to hold down the Power and the Volume Key. You should able to see the Android image and a bunch of information about your device. There should also be a “Start” at the top right corner of the screen.

Step 3: Press the Volume up and Volume down keys and use the Power key to select menu options. Press the Volume down key twice to see “Recovery Mode” in red at the top of the screen. Press the Power key to select it.

Step 4: The white Google logo will appear immediately followed by the Android logo again as well as the words “No Command” at the bottom of the screen.

Step 5: Finally, press and hold both the Power and the Volume up Key for around 3 seconds and then let go of the Volume up Key but keep holding the Power Key. You should see the Android system recovery options at the top of the screen. Use the Volume keys to highlight and the Power key to select the one you want.

Part 3. Android Stuck at System Recovery? How to fix in one click?

Sometimes during the System Recovery process, the process can glitch, and you’ll lose data on your device, rendering it unusable. However, another solution to fix this is to repair your device using the Dr.Fone - System Repair tool.

Dr.Fone - System Repair (Android)

One-stop solution to fix Android stuck at System recovery

• It’s the #1 software for PC-based Android repair
• It’s easy to use with no technical experience required
• Supports all latest Poco C50 devices
• Easy, one-click fix Android stuck at system recovery

3981454 people have downloaded it

Here’s a step by step guide on how to use it yourself;

Note: Be aware that this process can erase all your personal files on your device, so ensure you’ve backed up your Poco C50 before continuing.

Step #1 Head over to the Dr.Fone website and download the software for your Windows computer.

Once installed on your computer, open onto the main menu and connect your Poco C50 using the official USB cable. Select the System Repair option.

Step #2 Select the ‘Android Repair’ option from the next screen.

Insert your device information, including the brand, carrier details, model and country and region you’re in to ensure you’re downloading the correct firmware.

Step #3 Follow the onscreen instructions on how to put your device in Download Mode.

Your device should already be in this mode but follow the instructions to make sure. There are methods available for devices, both with and without home buttons.

Step #4 The firmware will now start downloading. You’ll be able to track this process in the window.

Ensure your device, and your computer stays connected the entire time, and make sure your internet connection remains stable.

After downloading, the software will automatically start to repair your device by installing the firmware. Again, you can track the progress of this on the screen, and you’ll need to ensure your device remains connected throughout.

You’ll be notified when the operation is complete and when you’re able to disconnect your phone and use it as normal, free from it being stuck on the Android system recovery screen!

Part 4. Android Stuck at System Recovery? How to fix in a common way?

If, however, your device is stuck on system recovery mode, here’s how you can easily get it out of system recovery. The process is slightly different for different Android devices, so you should check your device’s manual before attempting this process.

Step 1: Power off the Poco C50 device, and just to be sure, take out the battery to ensure that the Poco C50 device is fully turned off. Then reinsert the battery.

Step 2: Press and hold down the Home button, Power Button, and the Volume up Key simultaneously until the Poco C50 device vibrates.

Step 3: Once you feel the vibration, release the power button but continue to hold down the Home and Volume up Key. The Android recovery screen will display. Release the Volume up and Home buttons.

Step 4: Press the Volume down key to select the “Wipe Data/ Factory Reset option and then press the Power button to select it.

Step 5: Next, you need to press the Volume down button to highlight “Delete All User Data” and then press the Power button to select it. The device will reset and present the “Reboot System Now” option.

Step 6: Finally, press the Power button to reboot the phone in normal mode.

Part 5. Backup and Restore Android System

Losing data on your Poco C50 is a common occurrence, and since Android devices don’t really have an automatic full backup solution, it is important to know how to backup and restore your device system. Here’s how to easily do that.

Step 1: Enter the recovery mode on your Poco C50, as described in Part 2 above. Use the Volume and Power keys to select the “Backup & Restore” option on the screen.

Step 2: Tap on the backup option or use the Volume and Power keys if your screen is unresponsive. This will begin backing up your system to the SD card.

Step 3: After the process is complete, choose “Reboot” to restart the Poco C50 device.

Step 4: You can then simply check Recovery > backup directory on your SD card. You can rename it to easily find it later during the restore process.

To restore the system from the backup created, follow these simple steps.

Step 1: Once again, enter recovery mode as described in part 2 above and then choose Backup & Restore from the menu list.

Step 2: Press “Restore” to begin the recovery process from the Backup file we created

Step 3: You will be notified when the system restore is complete.

Android system recovery mode can be quite useful, especially when your system is unresponsive. As we have also seen, it is important to know how to get into and out of System Recovery mode if you are going to backup and restore your Android system. It is also quite easy to do both of these things.

7 Fixes for “Unfortunately, Phone Has Stopped” on Poco C50

Encountering issues with the Phone app is never welcoming. Being one of the useful apps, seeing it crashing and unresponsive gives sheer despondency. If talked about the triggering points, they are numerous. But the central point is what to do when the Phone app keeps crashing. In this article, we have discussed this issue in detail. To know this and more about why the “Unfortunately, Phone has stopped” error crops up, read this article and get the problem sorted on your own.

Part 1: When can the “Unfortunately, Phone has stopped” error come?

First things first! You need to stay updated on why the Phone app keeps stopping or crashing before jumping to any solution. Following are the points when this error comes up to annoy you.

• When you install a custom ROM, the issue might occur.
• The upgrading of the software or incomplete updates can lead to crashing the Phone app.
• Data crashes can be another reason why this error shows up.
• Infection through malware and virus on your phone is also included when the Phone app might crash.

Part 2: 7 Fixes for the “Unfortunately, Phone Has Stopped” error

2.1 Open the Phone app in Safe Mode

First and foremost, the thing that can let you get rid of this trouble is Safe Mode. It is a feature that will end any excessive background functioning of the Poco C50 device. For instance, your device will be able to run sans any third-party apps when in Safe mode. Since the important functions and the naïve apps will be running on the Poco C50 device, you will get to know if it’s really a software glitch or not by running the Phone app in Safe mode. And this is the first solution we would recommend you make use of when the Phone app has stopped. Here is how to enable Safe Mode.

1. Switch off the Poco C50 phone first.
2. Now keep pressing the “Power” button until you see the Poco C50 logo on the screen.
3. Release the button and immediately press and hold the “Volume Down” key.
4. Leave the key once the Poco C50 device is in Safe mode. Now, the third-party apps will be disabled and you can check if the Phone app is still not responding or everything is fine.

2.2 Clear the cache of the Phone app

The cache should be cleaned timely if you want any app to work properly. Due to the constant usage, the temporary files get collected and may corrupt if not cleared. Hence, the next solution you should try when the Phone app keeps stopping is to clear the cache. Here are the steps to be performed.

1. Open “Settings” on your device and go to “Application” or “Apps”.
2. Now from the list of all applications, go to “Phone” and tap on it.
3. Now, click on “Storage” and choose “Clear Cache”.

2.3 Update Google Play services

Since Android is created by Google, there must be some Google Play services that are crucial to run several system functions. And if attempting the previous methods isn’t of any use, try updating Google Play services when you find the Phone app stopped. For doing this, you need to make sure that automatic updates are turned on in Google settings. If not, enable it and get the apps including Google Play services updated for smoother functions.

2.4 Update the Poco C50 firmware

When the firmware is not updated, it may conflict with some apps and maybe that’s why your Phone app falls prey. Therefore, updating Poco C50 firmware will be a sane step that should be taken when the Phone app has stopped. Follow the below-mentioned steps and then check if the Phone app is opening or not.

1. Open “Settings” and go to “About Device”.
2. Now tap on “Software Updates” and check for the availability of the new update.

1. Download and install it and then try to use the Phone app.

2.5 Clear partition cache

Here is another resolution for the “Unfortunately Phone has stopped” error. Clearing the partition cache will remove the whole cache of the Poco C50 device and make it work like before.

1. Switch off your device to begin with and enter the recovery mode by pressing the “Home”, “Power” and “Volume Up” buttons.
2. The recovery mode screen will appear now.
3. From the menu, you need to choose “Wipe Cache Partition”. For this, you can use the Volume keys to scroll up and down.
4. To select, press the “Power” button.
5. The process will begin and the Poco C50 device will restart post it. Check if the problem still persists or it is finished. If unfortunately not, get to the next and the most productive solution.

2.6 Get the Poco C50 system repaired in one click

If still, the Phone app keeps stopping after trying everything, here is the most effective method that can surely help you. Dr.Fone - System Repair (Android) is a one-click tool that promises to repair Android devices hassle-free. Be it apps crashing, the black screen, or any other issue, the tool has no problem fixing any sort of issue. Here are the benefits of Dr.Fone - System Repair (Android).

Dr.Fone - System Repair (Android)

Android repair tool to fix “Unfortunately, Phone Has Stopped” on Poco C50 devices.

• It takes no special skills to operate it and fairly works to bring the Android system to normalcy.
• It shows great compatibility with all Poco C50 devices and other Android phones supporting over 1000 Android brands.
• Fixes any kind of Android issue without any complication.
• Easy to use and trusted by millions of users and therefore has a higher success rate.
• Can be downloaded freely and friendly user interface.

3,106,444 people have downloaded it

How to fix crashing Phone app using Dr.Fone - System Repair (Android)

Step 1: Get the Software Installed

Click the “Start Download” button to download the tool on your computer, and then open the program to begin the repair, click on “System Repair”.

Step 2: Plug the Phone with PC

Take your original USB cord and then connect your Poco C50 to the computer. When the Poco C50 device is connected, click on “Android” from the two tabs > click “Start”

Step 3: Enter the Details

As the next step, enter some important details on the next screen. Be sure to enter the right name, brand, and model of the Poco C50 device. When done everything, verify once and click on “Next”.

Step 4: Downloading Firmware

Downloading firmware will be the next step. Prior to this, you have to go through the instructions given onscreen to enter the DFU mode. Please click on “Next” and the program will bring the suitable firmware version and start downloading it.

Step 5: Get the Poco C50 device Repaired

When you see the firmware has been downloaded, the issue will begin to get resolved. Hang on and wait until you get notified for the repair of the Poco C50 device.

safe & secure

2.7 Factory reset

If none of the above methods worked for you, the last resort you are left with is a factory reset. This method will wipe everything from your device and make it function like normal. We also suggest you make a backup of your data if it is important so as to prevent the loss. Here is how to do this to fix the crashing Phone app.

1. Open “Settings” and go to the “Backup and Reset” option.
2. Look for “Factory data reset” and then tap on “Reset phone”.
3. Within a while, your device will go through resetting and boot up to normalcy.

safe & secure