How to Fix the Soft Bricked Poco X6 Pro? | Dr.fone

How to Fix the Soft Bricked Poco X6 Pro? | Dr.fone

Abel Lv11

How to Fix the Soft Bricked Poco X6 Pro?

Bricked phone is a serious problem, as your brick smartphone could be suffering from a soft brick or hard brick problem, and must be dealt with carefully. It is very common to see a brick smartphone these days. If you are wondering what exactly is a bricked phone, here is your answer.

A bricked phone, hard brick or soft brick, is a smartphone which refuses to start or boot all the way up the home/main screen of the Poco X6 Pro device. This issue is observed within most Android phones because users have a tendency to tamper with the Poco X6 Pro device settings, flashing new and customized ROMs and tweaking with the essential files. Playing around with the phone’s internal set-up leads to such errors, worst of them being a brick smartphone. Usually, a bricked phone does not switch on and stays frozen at the Poco X6 Pro device logo, a blank screen or even worse, doesn’t respond to any command, even the power on command.

If you are confused about the soft brick and hard brick problems and looking for solutions to fix your priced phone, then here is all you need to know.

Read on to find out more.

Part 1: What is the difference between soft brick and hard brick?

To begin with, let us understand the basic difference between a soft brick and hard brick issue. Both versions of a bricked phone prevent it from booting but differ in their causes and gravity of the problem.

A soft-brick problem is caused merely by a software error/crash and makes your device switch on automatically every time you manually turn it off. This phenomenon is referred to as Boot Loop. Soft bricked Android phones are not as difficult to fix as the hard bricked Android phones. It is convenient to say that a soft bricked phone only boots up half-way and not fully, whereas a hard bricked device does not switch on at all. A hard brick error is thus caused when the kernel, which is nothing but an interface for the software to communicate with the hardware, is tampered with. A hard bricked phone is not recognized by your PC when plugged in and is a serious problem. It requires troubleshooting techniques and cannot be easily fixed as the soft brick problem.

hard bricked v/s soft bricked

Hard bricked phones are a rare sight, but the soft brick is very common. Given below are ways to fix a soft brick Android phone. The techniques listed here are the best and the most efficient ways to get your phone back to its normal working conditions without losing your important data or damaging your device or its software.

Part 2: Stuck at the Boot Loop

This is the first sign of a soft bricked Android phone. Boot Loop is nothing but when your phone does not remain switched off and turns itself on automatically, and freezes at the logo screen or blank screen, every time you manually try to power it off.

Stuck at boot loop problem can be fixed by clearing your Cache partitions. These partitions are nothing but storage locations for your modem, kernels, system files, drivers and built-in Apps data.

It is advisable to clear Cache partitions regularly to keep your phone free from such glitches.

Since the phone refuses to boot, Cache can be cleared from entering into the Recovery Mode. Different Android devices have different ways to put it in recovery mode. Normally pressing the power key and volume down key helps, but you may refer to your phone’s guide for better understanding and then follow the steps given below to clear the cache partition:

Once you are the recovery mode screen, you will see a number of options as shown in the screenshot.

recovery mode

Use the volume down key to scroll down and select ”Wipe cache partition” as shown below.

”Wipe cache partition”>

After the process is completed, select “Reboot System” which is the first option in the recovery mode screen.

This method will help you erase all the clogged up and unwanted files. You may loose some App related data, but that is a small price to pay to fix your bricked phone.

If this method does not boot up your brick smartphone and the problem still persists, there are two more things you can try. Read ahead to find out about them.

Part 3: Booting straight into recovery mode

If your bricked phone does not boot up to your Home Screen or Lock screen and instead boots directly into Recovery Mode, there is not much left to do. Booting straight into recovery mode is undoubtedly a soft brick error but it also indicates a possible problem with your current ROM. The only option you have to flash a new ROM to reboot your bricked phone back to its normal functioning.

To flash a new ROM:

Firstly, you must root your phone and unlock the Bootloader. Every phone’s mechanism to unlock the bootloader is different, thus, we suggest to refer to your user manual.

Once the Bootloader is unlocked, take a backup of all your data by selecting “Backup” or “Android” back in recovery mode. The process should not take long and all you need to do is tap “OK” to config backup.

backup and restore

In this step, download a ROM of your choice and store it in your SD Card. Insert the SD Card in your phone to begin the flashing process.

Once at the recovery mode, select “Install Zip from SD Card” from the options.

install zip from sdcard

Scroll down using the volume key and use the power key to select the downloaded ROM.

Scroll down

select the downloaded ROM

This might take a few minutes of your time, but once the process is complete, reboot your phone.

Hopefully, your bricked phone will not boot normally and work smoothly.

Part 4: Booting straight into Bootloader

If your bricked phone boots straight into Bootloader, then this a serious issue and must not be taken lightly. Flashing a new ROM or clearing cache partitions are of little help in such a brick smartphone situation. Booting straight into Bootloader is a peculiar soft bricked Android phone feature and can be tackled only by downloading and flashing your original ROM from the manufacturer. In order to do so, a detailed study about your manufacturer’s ROM, ways to download and flash must be carried out. Since different Android phones come with different types of ROMs, it difficult to cover all the aspects about the different types of ROMs.

Brick smartphone problem has become more prominent than phone freezing or hanging issue. Android users are often seen looking for solutions to fix their soft brick and hard brick phones. Android phones are prone to get bricked and thus, it is important for us to know about the three techniques given above. These methods have been tried, tested and recommended by ay affected bricked phone users. Therefore, these tips are reliable and worth a try. So if your phone acts stubborn and refuses to boot normally, examine the problem carefully and adopt one of the solutions given above which best suits your situation.

Fix Unfortunately Settings Has Stopped on Poco X6 Pro Quickly

All of you, sooner or later, must have found the “Unfortunately Settings has stopped” error on your Poco X6 Pro. The problem can occur if the Settings keeps stopping or crashing. Many times, you may try to open the Settings but it doesn’t even open. Or possibly, it may freeze after getting opened thereby hampering the Poco X6 Pro device’s performance.

unfortunately settings has stopped

Well! There can be a number of reasons why this thing happens. For instance, custom ROM installations, not enough space in the Poco X6 Pro device or perhaps an outdated version of Android. If you are struggling with the same issue and want to know what to do when Android Settings is not responding, this post will help you. We have explained everything in detail along with the solutions. So, scroll down and get things sorted.

Part 1: Clear the cache of Settings and Google Play Service

It is possible that the corrupted cache files are responsible for this error. Hence, as the first tip, we would like you to clear the Settings cache if that is what triggers the “Unfortunately Settings has stopped” issue. Clearing it would definitely make Settings run appropriately. And The steps to clear the cache of the Google Play Services app are similar. Here is how to clear the cache of Settings:

  1. Open “Settings” on your Poco X6 Pro and choose “Apps & Notifications”/”Apps”/”Application Manager” (the option may differ on different devices).
  2. In the list of applications, look for “Settings” and open it.
  3. Now, select “Storage” followed by “Clear Cache”.

settings crashing - clear cache

Note: In some phones, the “Clear Cache” option may come after tapping on “Force Stop”. Therefore, go accordingly without getting confused.

Part 2: Clear the Android phone’s RAM and retry

As the next tip, we would like to suggest you clear your device’s RAM by ceasing the running apps in the background. RAM, if at the increased level, is responsible for the Poco X6 Pro device’s freezing, poor performance, and most probably is the reason behind crashing Settings. Also, if the apps in the background keep running, they might conflict with the Settings and stop it to perform properly. Therefore clearing RAM is important when Android Settings is not responding. Here is how to do it.

  1. Firstly, you need to go to the Recent apps screen. For this, long-press the Home key.
    Note: Please note that different devices have different ways to go to the Recent apps screen. Do it according to the Poco X6 Pro device you own.
  2. Now, swipe the apps and tap on the clear option. You will be able to notice the amount of RAM cleared

settings crashing - clear ram

Part 3: Uninstall the Google update

Uninstalling Google Play Store updates has also responded well to many users. It has worked in the case of the “Unfortunately Settings has stopped” error. So, we would also like to suggest you use this tip if the others don’t work. Here are the steps to be followed for this.

  1. Open “Settings” on your Android and tap on “Application manager” or “Apps” or “Application.
  2. Now, head to all the apps and select “Google Play Store” from there.
  3. Tap on “Uninstall Updates” and restart your device to check if the crashing Settings issue has been resolved.

settings crashing - uninstall update

Part 4: Uninstall the custom ROM or re-flash the stock ROM

Using a custom ROM on your device brings up this problem due to incompatibility or improper installation. Therefore, you should either uninstall the custom ROM or re-flash the stock ROM. in order to re-flash the stock ROM of your Poco X6 Pro, the best way would be Dr.Fone - System Repair (Android). It offers one-click functionality to flash stock ROM and that too with full security. Supporting all Poco X6 Pro devices, it ranks among its counterparts when it comes to fixing crashing Phone app issues or any other Android system issue. It is loaded with the beneficial features which are discussed below.

Dr.Fone - System Repair (Android)

Android repair tool to fix “Unfortunately, Settings Has Stopped”

  • You needn’t be a tech-savvy to use this
  • Supports a wide range of Android devices easily, 1000+ being more precise
  • One-click tool and supports any sort of Android system issue
  • Higher success rate along with millions of trusted users
  • Trustworthy and offers an extremely easy interface

4,635,310 people have downloaded it

How to fix crashing Settings using Dr.Fone - System Repair (Android)

Step 1: Download Tool

Visit the official website of Dr.Fone and download the toolbox from there. Go for the installation process and wait until the installation gets over. Launch it now and choose the “System Repair” tab from the main window.

Android settings not responding- download tool

Step 2: Get the Phone Connected

With the help of a USB cable, plug your Poco X6 Pro into the PC. Upon proper connection, hit on the “Android Repair” option from the left panel.

Android settings not responding - connect android

Step 3: Feed Correct Information

In the next window, you need to fill in some necessary information like the name and model of the mobile device. Enter details like country and career. Check once and hit on “Next”.

Android settings not responding - enter details

Step 4: Enter Download Mode

Now, you need to take your device into Download mode. For this, you need to follow the onscreen instruction according to your device. Click “Next” and you will notice the firmware downloading progress on your screen.

Android settings not responding - download mode

Step 5: Repair the Issue

Once the firmware is completely downloaded, your Poco X6 Pro will automatically start getting repaired. Stay there and you will receive a notification that the repair is done.

Android settings not responding - fix the issue

Part 5: Wipe cache partition to restore Settings

Like RAM, wiping cache is also vital so as to make the Poco X6 Pro device’s operation smoother. And when you are getting the “Unfortunately Settings has stopped” error, it might be due to the collected cache. To remove it, you will need to enter the recovery mode. And the steps for recovery mode range from device to device. For instance, Poco X6 Pro users have to press the “Home”, “Power” and “Volume Up” buttons. Similarly, HTC and LG device users are supposed to press the “Volume Down” and “Power” buttons. For Nexus, it is “Volume Up, Down” and Power key combinations. Therefore, before going further, make sure what device you own and enter the recovery mode according to it. Now, follow the detailed guide below to wipe the cache partition in order to fix crashing Settings.

  1. Primarily, turn off the Poco X6 Pro device and enter the recovery mode by pressing the respective key combinations.
  2. You will notice a Recovery screen on your device.
  3. On showing up the recovery screen, look for the “Wipe Cache partition” option and use the “Volume Down” and “Volume Up” buttons to scroll down and up respectively.
  4. On reaching the required option, press the “Power” button to start wiping.
  5. Once finished, click the reboot option and the Poco X6 Pro device will be rebooted, fixing the issue hopefully.

Android settings not responding - cache partition

Part 6: Factory reset your Android

You can also opt for Factory resetting your device to fix the issue of Settings keeps stopping. By removing everything from the Poco X6 Pro device, it will make your device run properly. If you have important data on your device, please make sure to create a backup before taking action if you don’t want to lose it. The steps are as follows.

  1. In the “Settings, go to “Backup and Reset”.
  2. Tap on “Factory data reset” followed by “Reset device”.
  3. Wait for the completion of the process and check if Settings is stopping or not after it gets rebooted.

Android settings not responding - factory reset android

Part 7: Check and update Android OS

A lot of times minor issues crop up due to the operating systems that get outdated. It is because the Poco X6 Pro device needs to get updated from time-to-time for proper functioning otherwise it will not be able to match up with the fading technologies thereby coming up with issues like “Unfortunately Settings has stopped”. We recommend here you check for the available update and update your device. For this follow the guide below.

  1. Go to “Settings” and tap “About Phone” on your device.
  2. Now, hit on “System Update” and the Poco X6 Pro device will look for any available update.
  3. If there is any, go along with the prompts to install it and make your phone even smarter.

Android settings not responding - update android firmware

Conclusion

If your Poco X6 Pro shows the “Unfortunately Settings has stopped” error, don’t worry. This problem can come from many things like old software or cache issues. You can try easy fixes like clearing cache or updating your system. Sometimes, removing custom ROMs might be needed.

For iOS users facing similar problems, we recommend using Dr.Fone-System Repair (iOS) . It’s known for fixing many iOS problems without losing any data. Remember, a well-working device is just a few steps away!

Safe download safe & secure

Super Easy Ways To Deal with Poco X6 Pro Unresponsive Screen

The evolution of smartphones signifies the development of mobile communication technology. Different from the initial years, they are not just used for messaging and calling but have many other applications. Poco X6 Pro cell phones are presently utilized for perusing the Internet and exploring through maps, photography, videography, and numerous other used cases. A development in arranged availability goes hand-in-hand with the development of cell phones.

Poco X6 Pro smartphones are gaining popularity owing to their low costs, high quality, and innovative features. High-resolution cameras, extensive battery life, and lightning-fast processing are just a few of the advantages of these mobile devices. Nevertheless, customers may sometimes need help with issues, such as a non-functioning Poco X6 Pro touchscreen, which may be challenging.

Some common issues might arise for Poco X6 Pro phone users. The Redmi note 4 touch not working is a serious problem. It can only go up to the initialization screen. In this guide, you’ll find the information you need to troubleshoot and fix the most common problems reported by Motorola customers.

What causes a Poco X6 Pro Screen to be unresponsive?

The screen on your Poco X6 Pro phone could stop responding for several reasons. The touchscreen, the system software, or the hardware itself might all be at fault. To effectively address an issue, it is crucial to locate its origins.

The following are some potential reasons for an unresponsive screen on a Poco X6 Pro device, along with descriptions of each.

There are signs of soft bricking

A touch screen not working on Poco X6 Pro smartphones indicates a soft brick (recoverable by firmware update), often caused by a defective or undercharged battery. System file corruption, old firmware, or failed upgrades are all possible causes. Several customers have complained that after installing a software update, their Poco X6 Pro 4 or 5 device’s screen became unresponsive and remained at the boot logo.

There might be issues with the Poco X6 Pro device itself

Screens on Poco X6 Pro devices may become unresponsive for a variety of hardware-related reasons. A broken LCD panel, faulty touch sensor, or loosened ribbon wires are all possible causes. Every Poco X6 Pro device, including the Note 4 and 5, is susceptible to these problems.

There might be errors in the updated software

The Android operating system is adjustable. Some of our technological advancements may backfire on us. The phone won’t power on or become stuck in a boot loop where the logo will only show intermittently. For example, some Poco X6 Pro 4 and 5 users have reported their screens are unresponsive after a software update, rendering the Poco X6 Pro device unusable.

The common solutions to solve a Poco X6 Pro Screen unresponsive

Could anything be more annoying than a broken touchscreen on your Poco X6 Pro phone? If this happens, the gadget is useless, and you won’t be able to do even the simplest tasks. Even so, it’s common for the screen to cease responding to touches.

Before taking the item in for repairs, see if you can figure out the problem independently. Do you want to learn the method? If the touch screens on your Poco X6 Pro stop working, don’t panic; we’ll teach you exactly what to do.

Solution 1: Try to restart your device

restart your phone

Giving your Poco X6 Pro a restart is one of the most common solutions if you encounter an unresponsive screen on your phone. Here’s how.

Step 1: Press and hold the power button until the screen becomes black;

Step 2: After 1 minute or so, hold the power button again to power on the Poco X6 Pro device.

Solution 2: Check your charging port and battery

xiaomi battery and charger

If the battery of your Poco X6 Pro is empty, your screen is expected to be unresponsive. To fix that, here are some easy steps for you:

  1. Charge your phone.
  2. Leave it for about an hour.
  3. Come back to check. Turn your phone on.
  4. Test if the touchscreen is now working.

Solution 3: Contact Customer Service

xiaomi contact customer service

Let’s assume you’ve applied every possible course of action. For example, your Poco X6 Pro 4 touchscreen is still unresponsive. You may contact the brand’s customer support department if you need assistance. When the time comes, they’ll always know what to do.

Based on the customer’s feedback, one of the frequent issues of the Poco X6 Pro is when the screen becomes unresponsive. These issues should not usually happen, but if you find yourself in this dilemma, a list of other solutions below will help you.

Solution 4: Turning on your full screen option offered by MI

full screen options

Steps to activate full screen gestures

Step 1: Browse you setting

Step 2: Search for full screen display

Step 3: From here, tap the screenshot on the right with the toggle labeled Full screen gestures

This may include gestures to get used to but it will also fix when your touchscreen sometimes stops responding.

Solution 5: Backup and Factory Reset is always a choice

factory reset on android

Doing a factory reset may be your last remaining choice if the preceding solutions are unsuccessful. If you do this, all of the information on your phone will be deleted.

Easy Steps in Doing a Factory Reset

  1. Press the power button until the phone shuts down
  2. When your phone shuts down, press and hold the power buttonand Volume down button at the same time until the Android logo displays on the screen.
  3. Recovery Menuwill appear in your screen, press volume down button until Factory reset is highlighted
  4. Press thepower button in selecting the Factory reset option and your phone should restart automatically.

Solution 6: Using Dr. Fone Android Repair Toolkit

dr fone system repair

If you want to fix issues like this, most simply, Dr. Fone offers that. It is made to provide you with a complete mobile solution. You may have your phone fixed without losing any information. Dr. Fone’s many handy tools will quickly get your phone back in working order.

How to avoid a Poco X6 Pro screen unresponsive?

Users may take several precautions to avoid the Poco X6 Pro screen unresponsive problem. Stop using any app stores or other unofficial app providers. There is a risk that doing so may damage your device or introduce viruses that will force your phone to restart. There’s also a risk of losing important information like photos and files.

Regularly updating the Poco X6 Pro phone’s software is necessary to keep it running smoothly and free of issues. Tools like Dr. Fone allow users to periodically maintain and restore data by cleaning the cache and deleting unused applications.

Avoiding severe temperatures and humidity may protect the Poco X6 Pro device’s internal components and keep the screen responsive. Using high-quality charging cords is also recommended. For once, consumers won’t have to worry about breaking the screen because they accidentally dropped their cell phones. If users follow these measures, they may reduce the likelihood that their Poco X6 Pro smartphone will have an unresponsive screen.

safe Download safe & secure

Conclusion

Sometimes, Poco X6 Pro smartphones may experience problems with their screen. This occurs if there is an issue with the functioning of a new app or a software update. Several Poco X6 Pro phone owners have reported problems with an unresponsive screen. However, the remedies outlined here should help you quickly and efficiently fix the issue and get your phone back up and running. Keep your phone updated, and remember to back up your data often to avoid this problem in the future.

When following the directions, the user may require more research into some troubleshooting techniques. If this is the case, Dr.Fone Repair is usually the solution. The fact that Dr. Fone can continually tweak his system of unresponsive screens is wonderful news. This helpful tool can fix both black screens and endless starting cycles. That’s why it’s an integral part of every modern computer.


  • Title: How to Fix the Soft Bricked Poco X6 Pro? | Dr.fone
  • Author: Abel
  • Created at : 2024-07-14 05:49:07
  • Updated at : 2024-07-15 05:49:07
  • Link: https://fix-guide.techidaily.com/how-to-fix-the-soft-bricked-poco-x6-pro-drfone-by-drfone-fix-android-problems-fix-android-problems/
  • License: This work is licensed under CC BY-NC-SA 4.0.