How to Fix the Soft Bricked Samsung Galaxy A54 5G?

Bricked phone is a serious problem, as your brick smartphone could be suffering from a soft brick or hard brick problem, and must be dealt with carefully. It is very common to see a brick smartphone these days. If you are wondering what exactly is a bricked phone, here is your answer.

A bricked phone, hard brick or soft brick, is a smartphone which refuses to start or boot all the way up the home/main screen of the Samsung Galaxy A54 5G device. This issue is observed within most Android phones because users have a tendency to tamper with the Samsung Galaxy A54 5G device settings, flashing new and customized ROMs and tweaking with the essential files. Playing around with the phone’s internal set-up leads to such errors, worst of them being a brick smartphone. Usually, a bricked phone does not switch on and stays frozen at the Samsung Galaxy A54 5G device logo, a blank screen or even worse, doesn’t respond to any command, even the power on command.

If you are confused about the soft brick and hard brick problems and looking for solutions to fix your priced phone, then here is all you need to know.

Read on to find out more.

Part 1: What is the difference between soft brick and hard brick?

To begin with, let us understand the basic difference between a soft brick and hard brick issue. Both versions of a bricked phone prevent it from booting but differ in their causes and gravity of the problem.

A soft-brick problem is caused merely by a software error/crash and makes your device switch on automatically every time you manually turn it off. This phenomenon is referred to as Boot Loop. Soft bricked Android phones are not as difficult to fix as the hard bricked Android phones. It is convenient to say that a soft bricked phone only boots up half-way and not fully, whereas a hard bricked device does not switch on at all. A hard brick error is thus caused when the kernel, which is nothing but an interface for the software to communicate with the hardware, is tampered with. A hard bricked phone is not recognized by your PC when plugged in and is a serious problem. It requires troubleshooting techniques and cannot be easily fixed as the soft brick problem.

Hard bricked phones are a rare sight, but the soft brick is very common. Given below are ways to fix a soft brick Android phone. The techniques listed here are the best and the most efficient ways to get your phone back to its normal working conditions without losing your important data or damaging your device or its software.

Part 2: Stuck at the Boot Loop

This is the first sign of a soft bricked Android phone. Boot Loop is nothing but when your phone does not remain switched off and turns itself on automatically, and freezes at the logo screen or blank screen, every time you manually try to power it off.

Stuck at boot loop problem can be fixed by clearing your Cache partitions. These partitions are nothing but storage locations for your modem, kernels, system files, drivers and built-in Apps data.

It is advisable to clear Cache partitions regularly to keep your phone free from such glitches.

Since the phone refuses to boot, Cache can be cleared from entering into the Recovery Mode. Different Android devices have different ways to put it in recovery mode. Normally pressing the power key and volume down key helps, but you may refer to your phone’s guide for better understanding and then follow the steps given below to clear the cache partition:

Once you are the recovery mode screen, you will see a number of options as shown in the screenshot.

Use the volume down key to scroll down and select ”Wipe cache partition” as shown below.

>

After the process is completed, select “Reboot System” which is the first option in the recovery mode screen.

This method will help you erase all the clogged up and unwanted files. You may loose some App related data, but that is a small price to pay to fix your bricked phone.

If this method does not boot up your brick smartphone and the problem still persists, there are two more things you can try. Read ahead to find out about them.

Part 3: Booting straight into recovery mode

If your bricked phone does not boot up to your Home Screen or Lock screen and instead boots directly into Recovery Mode, there is not much left to do. Booting straight into recovery mode is undoubtedly a soft brick error but it also indicates a possible problem with your current ROM. The only option you have to flash a new ROM to reboot your bricked phone back to its normal functioning.

To flash a new ROM:

Firstly, you must root your phone and unlock the Bootloader. Every phone’s mechanism to unlock the bootloader is different, thus, we suggest to refer to your user manual.

Once the Bootloader is unlocked, take a backup of all your data by selecting “Backup” or “Android” back in recovery mode. The process should not take long and all you need to do is tap “OK” to config backup.

In this step, download a ROM of your choice and store it in your SD Card. Insert the SD Card in your phone to begin the flashing process.

Once at the recovery mode, select “Install Zip from SD Card” from the options.

Scroll down using the volume key and use the power key to select the downloaded ROM.

This might take a few minutes of your time, but once the process is complete, reboot your phone.

Hopefully, your bricked phone will not boot normally and work smoothly.

Part 4: Booting straight into Bootloader

If your bricked phone boots straight into Bootloader, then this a serious issue and must not be taken lightly. Flashing a new ROM or clearing cache partitions are of little help in such a brick smartphone situation. Booting straight into Bootloader is a peculiar soft bricked Android phone feature and can be tackled only by downloading and flashing your original ROM from the manufacturer. In order to do so, a detailed study about your manufacturer’s ROM, ways to download and flash must be carried out. Since different Android phones come with different types of ROMs, it difficult to cover all the aspects about the different types of ROMs.

Brick smartphone problem has become more prominent than phone freezing or hanging issue. Android users are often seen looking for solutions to fix their soft brick and hard brick phones. Android phones are prone to get bricked and thus, it is important for us to know about the three techniques given above. These methods have been tried, tested and recommended by ay affected bricked phone users. Therefore, these tips are reliable and worth a try. So if your phone acts stubborn and refuses to boot normally, examine the problem carefully and adopt one of the solutions given above which best suits your situation.

How to Fix It: Samsung Galaxy A54 5G Won’t Turn On

Did your Samsung Galaxy A54 5G decide to go on vacation and refuses to turn on? If your Samsung Galaxy A54 5G won’t turn on for no apparent reason, finding why it failed to power on and the solution for it is not a fun process.

Here, we hope we are able to give you a checklist of reasons behind this issue and the possible steps you can take to rectify it.

Part 1: Common Reasons That Your Samsung Galaxy A54 5G Won’t Turn On

If you cannot find any reason why your Samsung Galaxy A54 5G will not switch on, here are some possible reasons:

1. Your Android phone is simply frozen in power-off or sleep mode. In which case, it fails to switch itself on or wake itself up when you initiate it.
2. Your phone’s battery may be out of charge.
3. The operating system or installed software is corrupted. The tell-tale sign if this is that if you manage to switch on your Samsung Galaxy A54 5G, it freezes or crash soon after.
4. Your device is clogged up with dust and lint causing the hardware to not work properly.
5. Your power button is broken , which caused it to not be able to trigger the necessary action needed to power up the Android phone. Check to also see if your connectors have no carbon build-up which will cause your phone to not be charged properly.

Part 2: Rescue Data on Android Phone That Will Not Turn On

If you need some help rescuing data from an Android phone that will not turn on, the Dr.Fone - Data Recovery (Android) will be your best friend in your data recovery attempt. With the help of this data recovery solution, you will be able to intuitively recover lost, deleted or corrupted data on any Android devices. Its flexibility and efficiency in rescuing data make it one of the best software out there.

Note: For now, the tool can rescue data from broken Android only if your phone is earlier than Android 8.0, or rooted.

Dr.Fone - Data Recovery (Android)

World’s 1st data retrieval software for broken Android devices.

• It can also be used to recover data from broken devices or devices that are damaged in any other way such as those stuck in a reboot loop.
• Highest retrieval rate in the industry.
• Recover photos, videos, contacts, messages, call logs, and more.
• Compatible with Samsung Galaxy A54 5G devices.

3981454 people have downloaded it

If your Samsung Galaxy A54 5G won’t turn on, here is how you can use the software to recover data:

Step 1: Launch Wondershare Dr.Fone

On your desktop computer or laptop, open Wondershare Dr.Fone. Click on Data Recovery on the left column. Connect your Samsung Galaxy A54 5G to the computer using a USB cable.

Step 2: Decide which file types to recover

On the next window, you will need to check the boxes corresponding to the type of files you can recover from a list. You can get back Contacts, Messages, Call History, WhatsApp messages & attachments, Photos, Audio and more.

Step 3: Select the problem with your phone

Opt for “Touch screen not responsive or cannot access the phone” or “Black/broken screen”. Click Next to continue.

Look up for your device – pick the Samsung Galaxy A54 5G device Name and Device Model. Advance by clicking on the Next button.

Step 4: Go into your Samsung Galaxy A54 5G’s Download Mode.

The data recovery tool will guide you on how you can go into your Samsung Galaxy A54 5G’s Download Mode. You should be getting a step-by-step guide on your computer.

Step 5: Scan the Android Phone.

Using the provided USB cable, attach your Samsung Galaxy A54 5G to your computer – the data recovery tool should be able to discover your device automatically and scan it for recoverable data.

Step 6: Review and Retrieve the Data from Broken Android Phone.

Wait for the program to finish scanning the phone – once completed, you will be able to get a list of recoverable files. You can have a preview of the file by highlighting them. Tick the box next to the file name and click on Recover to start retrieving the files and save them in the destination of your choosing.

Part 3: Android Phone Won’t Turn On: One Click Fix

After repeated attempts, when your Android mobile/tablet stops buzzing, what options do you have to revive it?

Well, we would recommend picking Dr.Fone - System Repair (Android) to fix an Android phone will not switch problem. This one-click Android system repair tool resolves every Android system issue without any fuss including Android Phone won’t turn on issue.

Dr.Fone - System Repair (Android)

The real fix to issues like “Android phone will not switch on”

• This tool is aptly effective for all the latest Samsung Galaxy A54 5G devices.
• With a high success rate for fixing Android devices, Dr.Fone - System Repair (Android) ranks at the top.
• This is a single click application to fix all Android system issues effortlessly.
• It is the first tool to repair all Android system issues in the industry.
• It is intuitive and requires no tech expertise to work with.

3981454 people have downloaded it

Prior to fixing the Android phone will not switch and getting things back in action. You need to make sure that you have backed up the Android device . It is recommended that rescuing data from an Android phone by backing up is better than recovering it post the process.

Phase 1: Get the Samsung Galaxy A54 5G device ready and connect it

Step 1: Run Dr.Fone on your computer once the installation is complete and tap the ‘Repair’ option form the interface. Now, connect your Android mobile with the computer.

Step 2: You will find a range of options, tap on the ‘Android Repair’ one. Hit the ‘Start’ button so that you can proceed to fix Android Phone won’t turn on hassle.

Step 3: Now, over the Samsung Galaxy A54 5G device information window, ensure to feed your exact device details. Press the ‘Next’ button then on.

Phase 2: Enter ‘Download’ mode for fixing your Samsung Galaxy A54 5G

Step 1: You need to put your Samsung Galaxy A54 5G in Download mode for resolving the Android phone will not switch on.

• For the Samsung Galaxy A54 5G device having ‘Home’ button, you got to switch it off and press ‘Volume Down’, ‘Home’, and ‘Power’ keys for 5-10 seconds at once. Let them go and click on the ‘Volume Up’ button to put your phone in ‘Download’ mode.

• For ‘Home’ button-less device, turn the phone/tablet down first. For 5 – 10 seconds, hold down the ‘Volume Down’, ‘Bixby’, and ‘Power’ buttons. Tap on the ‘Volume Up’ button to get into the ‘Download’ mode, after releasing the 3 buttons.

Step 2: Hitting the ‘Next’ key will allow you to download firmware and proceed with the next step.

Step 3: Dr.Fone - System Repair (Android) would verify your firmware download and then take a while to rectify and resolve Android Phone won’t turn on issue.

Part 4: Android Phone Won’t Turn On: Common Fix

To try fixing an Android Phone that won’t turn on, follow these steps:

1. For any Android devices, remove the battery (considering the battery of your Samsung Galaxy A54 5G can be removed) and leave it out for at least 30 minutes. Put back the battery in and try to turn it on.
2. Press and hold down the Power and Volume Down buttons at the same time for 15-30 minutes to reboot the Samsung Galaxy A54 5G device.
3. Should the first two steps do not work, charge your Samsung Galaxy A54 5G to get it out of the start-up loop. You can also opt to use a different battery, just in case your current battery is the source of the problem.
4. If there are any connected hardware e.g. SD card, remove them from the Samsung Galaxy A54 5G device.
5. Start your Samsung Galaxy A54 5G in Safe Mode by pressing and holding down the Menu or Volume Down button on your device.
6. Should the first five steps do not work for you, perform a hard reset. Do take note that each device will have a different way to do so and that data that is stored locally on the phone will be deleted.
7. Send your Samsung Galaxy A54 5G to the repair shop should none of these steps work.

Part 5: Useful Tips to Protect Your Samsung Galaxy A54 5G

There are several reasons as to why your Samsung Galaxy A54 5G won’t turn on. The problem could be a hardware or software issue which could be prevented. Here are some useful tips to protect your Samsung Galaxy A54 5G.

I. Hardware

• Remember that the components that make your Samsung Galaxy A54 5G is sensitive. To protect these components from being damaged, use a good guard casing.
• Take apart your Samsung Galaxy A54 5G and clean it routinely to avoid dust and lint from clogging the phone and overheating it.

II. Software

• It is recommended to download apps from Google Play Store. This way, you can be sure that your app comes from a trusted source.
• Read the app’s permission to see which part of the operating system and your personal information that you are giving access to.
• Install reliable anti-virus and anti-malware software to safeguard your Samsung Galaxy A54 5G from malicious attacks.
• Make sure you update your operating system, software and apps to make sure you have the latest version – the developer may have fixed the bugs that have caused problems on Android phones.

It is important to note that your phone contains some important data. Therefore, when your Samsung Galaxy A54 5G won’t turn on do not just give up - there are plenty of tools at your disposal to recover back your files and phone.

Authentication Error Occurred on Samsung Galaxy A54 5G? Here Are 10 Proven Fixes

There are times when users get an authentication error while they connect to a Wifi network. The problem is mostly found in Android whenever a device tries to establish a connection to Wifi. If your device is also experiencing an authentication problem Wifi, then don’t worry. It can easily be resolved. In this post, we will make you familiar with the root cause for the Samsung Galaxy A54 5G Wifi problem and how you can resolve whenever authentication error occurred on your device.

Part 1: Any idea about the Wi-Fi authentication problem?

Wi-Fi authentication has to be done every time you wish to connect to a Wi-Fi network over your smartphone or laptop. To authenticate yourself and connect to the protected Wi-Fi network, you need to have the password of it. But if after you’re putting in the correct password and still experiencing the wifi authentication problem. Here’s what you need to know.

Authentication error occurs when the “deal” between the Wi-Fi router and device fails due to certain reasons. First, the Samsung Galaxy A54 5G device sends the password of the network and the “connect” request in an encrypted format to the Wi-Fi router. Then, the router decrypts the password and compares the password saved on it. Now, if the password matches, it sends affirmation for the “connect” request, and then the Samsung Galaxy A54 5G device is allowed to connect to the network.

Part 2: Why Authentication Error Occurred when Connecting to Wifi?

There could be plenty of reasons for facing an authentication error on your device. Most of the time, it occurs whenever a Wifi router seems to malfunction. Furthermore, if your phone has been recently updated, then chances are that there could be an issue with its drivers. A security attack can also make your device malfunction as well. An unstable connection or a router blockage can also be a reason for this issue.

In this scenario, whenever you try to connect to a Wifi network (even after supplying the correct password and username), it doesn’t connect to it. Instead, it displays an authentication error occurred promptly. Thankfully, there are plenty of ways to overcome the authentication problem Wifi. In the next section, we have provided three different solutions to fix the Samsung Galaxy A54 5G Wifi problem (as it mostly happens on Android devices).

Part 3: 10 Solutions to Fix Wifi Authentication Error

Before we make you familiar with different fixes for the Wifi authentication error, it is important to check your router beforehand. Chances are that you could be getting the authentication error because your router is not functioning properly. You can restart it and try to connect any other device to it as well to check it. After making sure that there is no problem with your network or router, follow these suggestions to overcome the authentication error occurred issue.

Check if extra characters added in Wi-Fi password

Ensure that no other extra characters are being added in the Wi-Fi password while you’re entering it. Key in the password carefully while viewing the characters, and then check if the authentication error occurs or not.

One-Click to Fix Wifi Authentication Error by Android System Repair

Android system repair is considered the most effective way to fix Wifi Authentication Error. As the bottom-layer Android system files may be corrupted unconsciously with days of phone use, the Wifi Authentication Error may be one of the symptoms.

So Android repair requires programming knowledge to do it?

No! With Dr.Fone - System Repair (Android), you can do Android repair in just a few steps and get all issues like Wifi Authentication error fixed easily.

Dr.Fone - System Repair (Android)

An easy-to-operate tool to fix Android system issues like a Wifi authentication error

• Fixes all Android system issues like a black screen of death, Wifi authentication error, etc.
• One-click to fix the Wifi authentication error. No technical skills required.
• Supports all the new Samsung Galaxy A54 5G devices like Galaxy S8, S9, etc.
• Easy-to-follow instructions provided on each of the screens.

3981454 people have downloaded it

Here are the steps to fix Wifi Authentication Error by Android system repair:

Note: Android repair is effective to permanently fix Wifi Authentication Error, but may wipe out the existing phone data. Backup all the important Android data to PC before you go on.

1. After the Dr.Fone tool is downloaded, install, and launch it. You can see the following screen.

1. Connect your Samsung Galaxy A54 5G to the computer, and select “Android Repair” in the middle.

1. Select all the details that match your device, and click “Next”.

1. Next up, you should boot your Samsung Galaxy A54 5G in download mode by following the on-screen instructions.

1. Allow the program to download the corresponding firmware. After that, the Android repair will start and get the Wifi Authentication Error fixed in minutes.

Use static IP address instead of DHCP

DHCP, or Dynamic Host Configuration Protocol is the default IP address assignment for the Wi-Fi settings on many devices. Whereas DHCP can cause IP address conflict during the dynamic IP address assignment. So, you’d better change “DHCP” to “Static” to see if the authentication error persists.

Step 1: Head to the “Settings” of your Samsung Galaxy A54 5G and then opt for “Wireless and Networks” followed by “WLAN/WiFi”.

Step 2: Now, hit on the WiFi network that is showing “authentication error occurred”.

Step 3: Depending on your Samsung Galaxy A54 5G model, look for “IP Settings” and tap on it. Now, switch the “DHCP” to “Static”.

Step 4: Note down the static IP address fields and wipe off all the fields. Punch it in again and then save it.

Check carefully for duplicate Wi-Fi names before you connect

Perhaps, you might connect to a WiFi with a similar name. There are good chances that some users do not modify their WiFi network name and possibly, your neighbor may have the same WiFi network, service provider. Therefore, ensure you connect to the correct WiFi network.

Reset the Wifi network

One of the easiest ways to fix the authentication problem of Wifi is to reset the network. To do this, you would be required to forget the respective network first and then connect to it again. This can be done by simply following these steps.

1. Firstly, you need to forget a Wifi network. To do it, go to your phone’s Settings > WiFi and network. From here, you can see a list of all the Wifi hotspots that your phone connects to. Select the network you wish to forget.

2. When you would select a network, it will provide the basic information related to it. Just tap on the “Forget” button and agree to the pop-up message. This will erase the network’s information from your device.

3. Afterward, turn on your Wifi again and tap to the network you wish to connect to. Simply provide the credentials and tap on the “Connect” button to reestablish the connection. This way, you can reset the network successfully.

Modify network connection

If the above solution won’t work, then you would be required to walk the extra mile to fix the Samsung Galaxy A54 5G Wifi problem. After you reset a network connection, if still getting issues regarding the authentication of the network, you need to modify the connection. In this technique, you will be changing the IP settings on your phone to alter the way it establishes a secure connection. You can do it by following these steps.

1. To start with, visit your phone’s Settings and open the Wifi page.

2. This will display a list of all the Wifi networks that are associated with your device. Just long-tap on the Wifi network that you wish to modify. It will open another pop-up window. From here, tap on the option of “Manage network settings”. Sometimes, users also get an option of “Modify network settings” here as well. Simply select it to proceed.

3. It will display basic information related to your Wifi network. Just tap on the “Show advanced options” button to access more options related to the network setting.

4. From the IP Settings menu, change the field from DHCP to Static. This will let you establish a static connection between your device and the router.

5. As soon as you will change it to static, you will get different fields related to your network’s IP address, gateway, DNS, and more. Simply fill these fields and tap on the “Save” button once you are done.

Now, try to connect to the Wifi hotspot again. You would be able to overcome the authentication problem of Wifi.

Change Network Security Type

It has been observed that, when we connect to Wifi, our device chooses a wrong security type. This clashes with the default security protocol of the router and authentication error occurred due to this. If your device is facing the same issue, then it can be fixed by simply changing its security type. To do this, follow these instructions:

1. To change the security type of a network, you need to “Add the network”. If you already have the Wifi network saved, then simply forget the network by following the above-mentioned tutorial.

2. Now, turn on your device’s Wifi and tap on the option of “Add network”. Here, you would be asked to give a network name and select the security type. To manually select it, tap on the “Security” option.

3. From here, you will get a list of various security protocols that you can pick. Select “WPA/WPA2-PSK” and save your selection.

Now, try to connect to the network again. Most likely, it will let you fix the authentication error on your device.

Update Android firmware to the latest

There are instances where an outdated OS version of your Samsung Galaxy A54 5G may create a hindrance in establishing a connection between your device and the WiFi network. You need to update your Android firmware to the latest version and then check if the problem persists or not.

Step 1: Launch “Settings” of your Samsung Galaxy A54 5G and then get into the “About Phone” option.

Step 2: Now, opt for the “System Update” option. If the update is available, get your device updated to the latest OS version.

Restart the router and reset Android network settings

Sometimes, the WiFi router may hang up while establishing a connection and therefore, the wifi authentication problem occurs. Try restarting your Wi-Fi router and then check if your device connects successfully. If this doesn’t work, try to reset your Android Network Settings .

Bonus tip: Turn Airplane mode on/off

By simply turning on the Airplane mode (and later turning it off), you can easily fix the authentication problem Wifi most of the time. You can find a toggle button for Airplane mode on the notification bar of your phone. If you can’t find it there, then go to your phone’s Settings > Connection > More Networks and turn on the feature of “Airplane Mode”.

Let it do for a while. Afterward, turn it off and try to connect to the Wifi network again.

After following these quick and easy suggestions, you would be able to fix the Samsung Galaxy A54 5G Wifi problem for sure. Even if you use any other Android device, then its authentication error can easily be resolved after these effective solutions. Go ahead and give these expert solutions a try and let us know about your experience as well. If you have any other solution to fix the authentication problem Wifi, then share it with us as well in the comments.