How to Fix the Soft Bricked Tecno Spark 20 Pro?

Bricked phone is a serious problem, as your brick smartphone could be suffering from a soft brick or hard brick problem, and must be dealt with carefully. It is very common to see a brick smartphone these days. If you are wondering what exactly is a bricked phone, here is your answer.

A bricked phone, hard brick or soft brick, is a smartphone which refuses to start or boot all the way up the home/main screen of the Tecno Spark 20 Pro device. This issue is observed within most Android phones because users have a tendency to tamper with the Tecno Spark 20 Pro device settings, flashing new and customized ROMs and tweaking with the essential files. Playing around with the phone’s internal set-up leads to such errors, worst of them being a brick smartphone. Usually, a bricked phone does not switch on and stays frozen at the Tecno Spark 20 Pro device logo, a blank screen or even worse, doesn’t respond to any command, even the power on command.

If you are confused about the soft brick and hard brick problems and looking for solutions to fix your priced phone, then here is all you need to know.

Read on to find out more.

Part 1: What is the difference between soft brick and hard brick?

To begin with, let us understand the basic difference between a soft brick and hard brick issue. Both versions of a bricked phone prevent it from booting but differ in their causes and gravity of the problem.

A soft-brick problem is caused merely by a software error/crash and makes your device switch on automatically every time you manually turn it off. This phenomenon is referred to as Boot Loop. Soft bricked Android phones are not as difficult to fix as the hard bricked Android phones. It is convenient to say that a soft bricked phone only boots up half-way and not fully, whereas a hard bricked device does not switch on at all. A hard brick error is thus caused when the kernel, which is nothing but an interface for the software to communicate with the hardware, is tampered with. A hard bricked phone is not recognized by your PC when plugged in and is a serious problem. It requires troubleshooting techniques and cannot be easily fixed as the soft brick problem.

Hard bricked phones are a rare sight, but the soft brick is very common. Given below are ways to fix a soft brick Android phone. The techniques listed here are the best and the most efficient ways to get your phone back to its normal working conditions without losing your important data or damaging your device or its software.

Part 2: Stuck at the Boot Loop

This is the first sign of a soft bricked Android phone. Boot Loop is nothing but when your phone does not remain switched off and turns itself on automatically, and freezes at the logo screen or blank screen, every time you manually try to power it off.

Stuck at boot loop problem can be fixed by clearing your Cache partitions. These partitions are nothing but storage locations for your modem, kernels, system files, drivers and built-in Apps data.

It is advisable to clear Cache partitions regularly to keep your phone free from such glitches.

Since the phone refuses to boot, Cache can be cleared from entering into the Recovery Mode. Different Android devices have different ways to put it in recovery mode. Normally pressing the power key and volume down key helps, but you may refer to your phone’s guide for better understanding and then follow the steps given below to clear the cache partition:

Once you are the recovery mode screen, you will see a number of options as shown in the screenshot.

Use the volume down key to scroll down and select ”Wipe cache partition” as shown below.

>

After the process is completed, select “Reboot System” which is the first option in the recovery mode screen.

This method will help you erase all the clogged up and unwanted files. You may loose some App related data, but that is a small price to pay to fix your bricked phone.

If this method does not boot up your brick smartphone and the problem still persists, there are two more things you can try. Read ahead to find out about them.

Part 3: Booting straight into recovery mode

If your bricked phone does not boot up to your Home Screen or Lock screen and instead boots directly into Recovery Mode, there is not much left to do. Booting straight into recovery mode is undoubtedly a soft brick error but it also indicates a possible problem with your current ROM. The only option you have to flash a new ROM to reboot your bricked phone back to its normal functioning.

To flash a new ROM:

Firstly, you must root your phone and unlock the Bootloader. Every phone’s mechanism to unlock the bootloader is different, thus, we suggest to refer to your user manual.

Once the Bootloader is unlocked, take a backup of all your data by selecting “Backup” or “Android” back in recovery mode. The process should not take long and all you need to do is tap “OK” to config backup.

In this step, download a ROM of your choice and store it in your SD Card. Insert the SD Card in your phone to begin the flashing process.

Once at the recovery mode, select “Install Zip from SD Card” from the options.

Scroll down using the volume key and use the power key to select the downloaded ROM.

This might take a few minutes of your time, but once the process is complete, reboot your phone.

Hopefully, your bricked phone will not boot normally and work smoothly.

Part 4: Booting straight into Bootloader

If your bricked phone boots straight into Bootloader, then this a serious issue and must not be taken lightly. Flashing a new ROM or clearing cache partitions are of little help in such a brick smartphone situation. Booting straight into Bootloader is a peculiar soft bricked Android phone feature and can be tackled only by downloading and flashing your original ROM from the manufacturer. In order to do so, a detailed study about your manufacturer’s ROM, ways to download and flash must be carried out. Since different Android phones come with different types of ROMs, it difficult to cover all the aspects about the different types of ROMs.

Brick smartphone problem has become more prominent than phone freezing or hanging issue. Android users are often seen looking for solutions to fix their soft brick and hard brick phones. Android phones are prone to get bricked and thus, it is important for us to know about the three techniques given above. These methods have been tried, tested and recommended by ay affected bricked phone users. Therefore, these tips are reliable and worth a try. So if your phone acts stubborn and refuses to boot normally, examine the problem carefully and adopt one of the solutions given above which best suits your situation.

How to Quickly Fix Bluetooth Not Working on Tecno Spark 20 Pro

One of the key features of an Android device these days is the Bluetooth technology. This is such an important part of the phone that many of us take for granted, but as soon as the feature stops working, it can cause all kinds of problems.

Fortunately, despite there being many reasons why a problem could occur to your Bluetooth feature, there are also plenty of fixes. Today, we’re going to share with you the complete guide that details everything you need to know to get your Bluetooth up and running once again as quickly as possible.

Let’s get straight into it!

Part 1. About Bluetooth Not Working on Android

Of course, the most common problem to occur with Bluetooth technology in your Tecno Spark 20 Pro is when it doesn’t connect to the Tecno Spark 20 Pro device you’re trying to link it to. This could be anything from a Bluetooth headset or headphones, to a portable speaker or even an in-car audio system.

However, the problems don’t stop there. You may have problems with turning your Bluetooth settings on through your actual device. Perhaps the software simply isn’t loading, or maybe the Bluetooth feature keeps turning itself off randomly.

Due to the complicated nature of Bluetooth technology, there could be many reasons as to why your Bluetooth feature is playing up in this way, but that doesn’t mean it can’t be fixed. For the rest of this guide, we’re going to explore the nine need-to-know ways you can fix the Bluetooth problems not working on your Tecno Spark 20 Pro as quickly as possible.

Part 2. 9 fixes for Bluetooth not working on Android

2.1 One click to fix Android Bluetooth issues due to Android system

Since Bluetooth is an internal technology, this indicates there’s a problem with the software or firmware of your Tecno Spark 20 Pro. If something’s broken, this means you need to fix it. Fortunately, there’s a quick and easy way to do this using software known as Dr.Fone - System Repair (Android).

Dr.Fone - System Repair (Android) is a powerful Android repair tool which is hailed as many as being on the best software applications in the industry. With all the tools you need to repair your phone not just for Bluetooth errors, but basically any internal firmware problems, this is a one-shot-tool that gets the job done.

Dr.Fone - System Repair (Android)

Android repair tool to fix Bluetooth issues in one click

• Can fix most internal software and firmware issues
• Trusted by over 50+ million people around the world
• Supports over 1,000+ unique Android brands, manufacturers, and devices
• Incredibly user-friendly and easy-to-use
• Compatible with all Windows computers

3981454 people have downloaded it

To ensure you have the best experience while using the Dr.Fone - System Repair (Android) software, here’s a complete step-by-step guide on how it works when fixing your Android’s Bluetooth problems.

Step One Make your way over to the Wondershare website and download the Dr.Fone - System Repair (Android) software to either your Mac or Windows computer. Install the downloaded file by following the on-screen instructions. Once installed, open the software, so you’re on the Main Menu.

Step Two Connect your Tecno Spark 20 Pro to your computer using the USB cable, wait a couple of seconds, and then click the System Repair option. On the Menu on the left, click Android Repair, and then press Start.

Step Three Next, use the drop-down menus to make sure all the information about your specific device is correct, including your device, operating system number, and carrier information. Click Next to confirm your selections.

Step Four When prompted, put your phone into Download Mode needed for repairs. You can do this by following the on-screen instructions which will depend on which device you have and the available buttons.

Step Five The software will now begin the repair process. This will happen automatically, and all you’ll need to do is make sure your device doesn’t disconnect during this process, and your computer doesn’t turn off.

When the repair process has been completed, you’ll receive the screen below, which means you can try again if the process didn’t work, or you can disconnect your Tecno Spark 20 Pro and start using it and your Bluetooth features.

2.2 Restart Android and turn on Bluetooth again

One of the most common solutions in technology is simply to turn it on and off again, which is the case to happen here. By restarting your device, you can clear out any problems you may be suffering from to help it get up and running again. Here’s how;

1. Turn your Tecno Spark 20 Pro off by holding down the Power button
2. Wait for several minutes and then turn your phone on again
3. Wait for your phone to completely power up, so you’re on the Main Menu
4. Navigate Settings > Bluetooth and then enable the setting
5. Try to connect your Bluetooth device to what you were trying to do before

2.3 Clear the Bluetooth cache

Every service on your Tecno Spark 20 Pro using a feature called a cache. This is where information is stored to help the feature run properly and give you the best experience. However, over time this can get messy and can cause problems with your Bluetooth feature.

By clearing the cache, you can restart the service and hopefully clear up any issues or problems you may be experiencing.

1. On your phone, navigate Settings > Application Manager, and you’ll see all the apps and services on your phone. Locate and select the Bluetooth service.
2. Select the Storage option
3. Tap the Clear Cache option
4. Go back of the Menu and restart your phone
5. Now turn your Bluetooth feature on and turn connecting it to your preferred device

2.4 Remove paired devices

Sometimes, you may have a problem with the Tecno Spark 20 Pro device you’re trying to connect to via Bluetooth, especially if this is a device you’ve updated. To counter and repair this, you’re going to need to remove the paired devices saved with your device and then reconnect them.

Here’s how;

1. From the Main Menu of your Tecno Spark 20 Pro, head to Settings > Bluetooth > Connected Devices.
2. Turn Bluetooth on, and you’ll see all the connections your Tecno Spark 20 Pro is paired with
3. Go through these settings and remove/delete/forget every connection on your device
4. Now when you go to connect to a device using Bluetooth, repair the Tecno Spark 20 Pro device, enter the passcode, and use a fresh paired connection.

2.5 Use Bluetooth in safe mode

If you’re having problems with your connection and paired devices, sometimes you may have conflicting software faults in your device that are causing the problems. If this is the case, you’ll need to boot your Tecno Spark 20 Pro in Safe Mode.

This is an operating state in which your phone will run the bare minimum services it needs to perform. If your Bluetooth works in Safe Mode, you know you have an app or a service that’s causing the problem.

Here’s how to find out;

1. Hold the power button down, so the Android power menu turns on
2. Long-press the power button again and the restart in Safe Mode option will come up
3. The phone will automatically boot into Safe Mode
4. Wait a minute on the Main Menu
5. Now turn on your Bluetooth and connect it to your preferred device

2.6 Turn on the discoverable feature

To ensure your Bluetooth can connect to other devices, it’s important to make sure you’re making your device discoverable to other Bluetooth devices. If it’s hidden, other devices won’t be able to find it, and sometimes it can bug and prevent connections.

Here’s how to turn on your Bluetooth discoverable feature;

1. From the home screen of your Android, navigate to the Menu> Settings > Bluetooth
2. Toggle the Bluetooth switch, so it’s on
3. Under the available settings, tick the box that allows your Bluetooth device to be discoverable
4. Turn your Bluetooth feature on and connect to the Tecno Spark 20 Pro device you’re trying to connect too

2.7 Exclude Bluetooth issues of the other device

Sometimes, you might not even have a problem with your Tecno Spark 20 Pro, but rather the Bluetooth device you’re trying to connect to, whether that’s a Bluetooth speaker, an in-car entertainment system, or any other kind of Bluetooth device.

By testing out another Bluetooth device to see if it will work with your preferred device, you can rule this out from being the issue.

1. Disconnect your Tecno Spark 20 Pro from the Bluetooth device and turn your Bluetooth off
2. Now take another Bluetooth device and connect this to the Tecno Spark 20 Pro device you’re trying to connect too. This could be another Android device, or even a computer or iOS device
3. If the new device doesn’t connect to your Bluetooth device, you’ll know there’s a problem with your Bluetooth device, not your Tecno Spark 20 Pro
4. If the Tecno Spark 20 Pro devices connect, you’ll know there’s a problem with your Tecno Spark 20 Pro

2.8 Place both devices within close proximity

One of the common misconceptions of Bluetooth is just how far the wireless range is of the service. You need to make sure your devices are well and truly close to each other to make sure a stable connection can be formed.

The further away the Tecno Spark 20 Pro devices are from each other, the less likely the connection will remain secure. As a rule of thumb, Bluetooth can work up to 100 meters, but to play it safe, always try and keep your devices under 50m apart.

2.9 Avoid interference of other Bluetooth sources

The final consideration you’ll want to think about is that Bluetooth radio waves, or wireless waves, can interfere with each other. This means they can bounce off each other or get muddled up and make things confusing from your devices.

With this in mind, you’ll want to make sure you’re limiting the amount of Bluetooth activity in the area where you’re trying to use a device. While uncommon, this could be the problem.

To fix this issue, turn off all the Bluetooth connections in the area. This includes computers, laptops, mobile phones, tablets, and any other Bluetooth devices you may have. Then, try connecting your Tecno Spark 20 Pro to the Tecno Spark 20 Pro device you were trying to use. If it works, you know you were experiencing Bluetooth interference.

Cellular Network Not Available for Voice Calls On Tecno Spark 20 Pro

The “Cellular Network Not Available for Voice Calls“ error is a common experience for many Android users. In our contemporary world, communication stands as the fundamental pillar of our existence. Yet, the malfunctioning of our devices hinders this connectivity. It often gives rise to numerous complications. Fortunately, your concerns are now a thing of the past.

This article serves as your guide for troubleshooting and overcoming this frustrating dilemma. It has compiled expert perspectives, valuable tips, and detailed, systematic solutions. The article will go through the underlying causes behind this issue and explore potential fixes. By the conclusion of this article, you’ll be armed with the necessary knowledge to tackle this problem.

Part 1. Preliminary Reasons For Cellular Network Not Available For Voice Calls

Facing the “Cellular Network Not Available for Voice Calls Android“ error can be overwhelming. Thus, it becomes evident that specific reasons underlie this issue. Solutions indeed exist to tackle this problem. Yet, comprehending the underlying reasons is equally crucial to resolve the issue:

1. Internet Access

One primary reason behind cellular network unavailability glitches lies in unstable internet access. Voice calls over cellular networks often require a stable internet connection. When this connection fluctuates or drops, it can result in the dreaded error message.

2. Terrain Coverage

Another contributing factor is the geographical terrain. In remote or sparsely populated areas, cellular tower coverage might be limited. It causes a signal disturbance or complete loss of the network.

3. Network Congestion

During peak usage hours or in densely populated areas, network congestion can also be a cause. It leads to temporary unavailability of the cellular network for voice calls. When the network is overloaded with traffic, it might struggle to accommodate more voice calls. That results in connectivity issues.

4. Technical Glitches

Furthermore, technical glitches within the Tecno Spark 20 Pro device or network infrastructure can cause this issue. These glitches could range from software bugs to hardware malfunctions.

5. Battery or Power Issues

In some instances, insufficient battery power or power-saving modes on devices can cause this issue. They affect the Tecno Spark 20 Pro device’s capacity to sustain a consistent connection with the cellular network. This consequently causes voice call unavailability.

Part 2. Prominent Solutions For Cellular Network Not Available For Voice Calls Android

A myriad of purposeful solutions exists to resolve the TracFone cellular network not available for voice calls issue. These solutions are specifically designed to address various underlying causes. The aim of these solutions is to restore smooth connectivity for voice calls. Described below are the top 8 solutions to fix the “Cellular Network Not Available” error:

Solution 1. Check the Availability of Cellular Networks

Before diving into complex fixes, the first thing to do is to check if nearby cell networks are available and how strong their signals are. It is an essential step when trying to fix the “Cellular Network Not Available“ error. This basic check ensures your phone is close enough to a working network tower, which matters for staying connected. It allows you to find out the availability of nearby cellular networks.

Moreover, with it, you can ensure your device is connected to a reliable network. This preliminary check sets the foundation for further troubleshooting.

Solution 2. Check the Airplane Mode of the Smartphone

Another crucial step in resolving this error involves ensuring that the Airplane Mode is disabled. This mode, when activated, disables all wireless connections. It also includes cellular networks, which could lead to connectivity issues. Follow these simple steps to check and disable Airplane Mode on your device:

Instructions: Swipe down on your phone’s screen from the top to access the Notification Panel, unveiling the Quick Settings tiles. Search for the airplane-shaped icon; if Airplane Mode is active, the icon will be highlighted or shown in a distinct color. Tap the Airplane Mode to turn off the Airplane Mode on your Android.

Solution 3. Selecting the Network Operator of the Tecno Spark 20 Pro device

In certain instances, manually selecting your network operator can help. It effectively resolves the “Cellular Network Not Available for Voice Calls Android“ error on your Tecno Spark 20 Pro. By choosing the network operator manually, you ensure a deliberate connection to a specific carrier. This potentially bypasses issues related to automatic network selection. Follow these steps to select your network operator manually:

• Step 1. Access “Settings” on your Tecno Spark 20 Pro, then tap on “Connections.” From there, navigate to “Mobile Networks” and proceed by selecting “Network Operators.”

• Step 2. Look for the “Automatically Select” toggle, which will be turned on. Toggle it off to see available networks and choose the one best suited to your device.

Solution 4. Restart Your Device

Sometimes, resolving the “Cellular Network Not Available for Voice Calls“ error on your Tecno Spark 20 Pro can be as simple as performing a restart. This basic troubleshooting step helps refresh the Tecno Spark 20 Pro device’s software. It clears temporary glitches and reestablishes essential connections, potentially resolving network-related issues. Follow these straightforward steps to restart your Tecno Spark 20 Pro:

Instructions: Hold down the “Power” button until the Power menu emerges on the display. From there, select “Restart” to initiate the Tecno Spark 20 Pro device’s reboot process.

Solution 5. Enable Roaming Settings

There are situations where you’re in an area with weak or no coverage from your primary network provider. In such a case, enabling roaming settings on your Tecno Spark 20 Pro can sometimes resolve the issue at hand. Enabling roaming allows your device to connect to partner networks. This extends your coverage beyond your home network’s reach. Follow these steps to enable roaming settings on your Tecno Spark 20 Pro:

• Step 1. Start by accessing your device’s Settings and tapping the “Connections” option. Here, scroll downward to press “Mobile Networks.”

• Step 2. Presently, you will encounter the “Data Roaming” option. Toggle this option on to enable data roaming on your device and resolve the issue.

Solution 6. Update Android Smartphone

Updating your Tecno Spark 20 Pro’s OS to the latest version can often resolve performance issues. It can also fix network connectivity issues, including the “Cellular Network Not Available” error. Manufacturers regularly release system updates containing bug fixes and security patches. It also includes enhancements that can address underlying software-related problems. Follow these steps to update your Android smartphone:

• Step 1. In your device’s Settings, scroll through to find the “Software Update” option. Select it, and on the subsequent screen, verify the availability of any updates.

• Step 2. If an update is accessible, select the ‘Download and Install’ choice. Then, proceed by following the prompts displayed on the screen to finalize the process.

Solution 7. Performing Factory Reset

Performing a factory reset is a drastic but effective measure. It can resolve persistent software-related issues, including the “Cellular Network Not Available” error. Be aware that initiating a factory reset results in the deletion of all data and settings stored on your device. Hence, it is crucial to back up any vital information before proceeding with this action. Here is how to fix the Verizon cellular network not available for voice calls:

• Step 1. To access your device’s “General Management” section, navigate through Settings. There, tap on “Reset,” and select “Factory Data Reset” from the subsequent screen.

• Step 2. You will need to tap “Reset” to confirm your choice. Then, follow the on-screen guidelines carefully to complete the reset process.

Solution 8. Contact Carrier Provider

If you’ve exhausted all options and the issue persists, reaching out to your carrier provider for assistance is a viable solution. Carrier providers can offer specific insights and guidance regarding network-related issues. When connected to customer service, explain the issue you’re experiencing in detail. Contacting your carrier provider enables you to tap into their expertise and resources.

You May Also Like:

Top 5 DFU Tools for iPhone to Enter DFU Mode

9 Ways to Fix iPhone Error 4013 or iTunes Error 4013

Tecno Spark 20 Pro ROM Download & Install: The Definitive Guide

Part 3. [100% Resolvable] Resolve Cellular Network Not Available For Calls Issues

Despite all your attempts, the cellular network not available for voice calls remains unresolved. It might state a more complex software-related issue or glitch within the Tecno Spark 20 Pro device. However, there’s a solution designed explicitly for addressing such complex issues. That software is Wondershare Dr.Fone, a comprehensive toolkit for Android devices. It stands out as the world’s first one-click Android repair tool.

Dr.Fone specializes in resolving a wide array of Android system issues, including the notorious black screen of death. With this tool, users can effortlessly restore their Android system to normal functionality.

Key Features of Wondershare Dr.Fone

1. Fone’s advanced repairing mechanism has the ability to repair even the bricked Android devices.
2. This tool supports more than 1000 models of Android devices across different brands for system repair.
3. It boasts the highest success rate when it comes to fixing Android devices.

Dr.Fone - System Repair (Android)

Repair Android System Errors without Any Trouble.

• Fix your Android to normal, no skills required.
• Fix various Android system issues, stuck in boot loop , black screen , or won’t turn on , looping on start, etc.
• The high success rate in resolving Android system issues.
• Compatible with a wide range of Android devices and OS versions
• User-friendly interface with easy-to-follow steps.

3981454 people have downloaded it

Steps Needed To Fix the Cellular Network Not Available for Calls Issue via Wondershare Dr.Fone

The following are the steps to resolve the Tracfone cellular network not available for voice calls using Wondershare Dr.Fone:

• Step 1. Open Wondershare Dr.Fone and Opt for System Repair

Launch the software. Then, navigate to the “Toolbox” section located in the left panel. Connect your Tecno Spark 20 Pro and proceed by choosing “System Repair.” Then, opt for “Android” to specify the Tecno Spark 20 Pro device type. On the subsequent screen, click “Start” to commence the repair procedure.

• Step 2. Provide Details of Your Android Device

The system automatically identifies the brand of the Android device undergoing repair. Afterward, choose the “Name,” “Model,” “Country,” and “Carrier” from the provided list options. If the Tecno Spark 20 Pro device is already unlocked, you can choose OPEN in the Carrier section. Then, confirm by checking the warning box indicating agreement and readiness to proceed. Click on “Next” to initiate the repair process for your Tecno Spark 20 Pro.

• Step 3. Complete the Android Repair Process Successfully

Follow the guidance displayed on your device’s screen to access Download Mode. Once in, the firmware download begins automatically. During this process, the platform verifies and presents the firmware details. Select “Fix Now” to proceed with the installation of the firmware onto your Tecno Spark 20 Pro. Since Android repair will result in the deletion of all data, input “000000” to confirm. This action initiates the system repair process.

safe & secure

3,336,459 people have downloaded it

Conclusion

In conclusion, facing the “Cellular Network Not Available for Voice Calls“ problem on your Tecno Spark 20 Pro can be frustrating. This article has explored many ways to fix this issue. These include simple checks like turning off Airplane Mode to solutions like contacting your carrier. However, when facing persistent network problems, a tool like Wondershare Dr.Fone becomes the only hope.

Among the various methods discussed, Dr.Fone stands out as a top choice. Its thorough system repair function targets and removes complex software glitches. The tool’s easy interface, broad compatibility, and secure repair process make it perfect. It is ideal for users looking for a reliable solution beyond regular troubleshooting.

Why isn’t My Tecno Spark 20 Pro establishing a connection with the cellular network?

What steps can I take when the mobile network isn’t available?

What might be causing my SIM card to not display a network?