How to Fix the Soft Bricked Xiaomi Redmi 13C?

Bricked phone is a serious problem, as your brick smartphone could be suffering from a soft brick or hard brick problem, and must be dealt with carefully. It is very common to see a brick smartphone these days. If you are wondering what exactly is a bricked phone, here is your answer.

A bricked phone, hard brick or soft brick, is a smartphone which refuses to start or boot all the way up the home/main screen of the Xiaomi Redmi 13C device. This issue is observed within most Android phones because users have a tendency to tamper with the Xiaomi Redmi 13C device settings, flashing new and customized ROMs and tweaking with the essential files. Playing around with the phone’s internal set-up leads to such errors, worst of them being a brick smartphone. Usually, a bricked phone does not switch on and stays frozen at the Xiaomi Redmi 13C device logo, a blank screen or even worse, doesn’t respond to any command, even the power on command.

If you are confused about the soft brick and hard brick problems and looking for solutions to fix your priced phone, then here is all you need to know.

Read on to find out more.

Part 1: What is the difference between soft brick and hard brick?

To begin with, let us understand the basic difference between a soft brick and hard brick issue. Both versions of a bricked phone prevent it from booting but differ in their causes and gravity of the problem.

A soft-brick problem is caused merely by a software error/crash and makes your device switch on automatically every time you manually turn it off. This phenomenon is referred to as Boot Loop. Soft bricked Android phones are not as difficult to fix as the hard bricked Android phones. It is convenient to say that a soft bricked phone only boots up half-way and not fully, whereas a hard bricked device does not switch on at all. A hard brick error is thus caused when the kernel, which is nothing but an interface for the software to communicate with the hardware, is tampered with. A hard bricked phone is not recognized by your PC when plugged in and is a serious problem. It requires troubleshooting techniques and cannot be easily fixed as the soft brick problem.

Hard bricked phones are a rare sight, but the soft brick is very common. Given below are ways to fix a soft brick Android phone. The techniques listed here are the best and the most efficient ways to get your phone back to its normal working conditions without losing your important data or damaging your device or its software.

Part 2: Stuck at the Boot Loop

This is the first sign of a soft bricked Android phone. Boot Loop is nothing but when your phone does not remain switched off and turns itself on automatically, and freezes at the logo screen or blank screen, every time you manually try to power it off.

Stuck at boot loop problem can be fixed by clearing your Cache partitions. These partitions are nothing but storage locations for your modem, kernels, system files, drivers and built-in Apps data.

It is advisable to clear Cache partitions regularly to keep your phone free from such glitches.

Since the phone refuses to boot, Cache can be cleared from entering into the Recovery Mode. Different Android devices have different ways to put it in recovery mode. Normally pressing the power key and volume down key helps, but you may refer to your phone’s guide for better understanding and then follow the steps given below to clear the cache partition:

Once you are the recovery mode screen, you will see a number of options as shown in the screenshot.

Use the volume down key to scroll down and select ”Wipe cache partition” as shown below.

>

After the process is completed, select “Reboot System” which is the first option in the recovery mode screen.

This method will help you erase all the clogged up and unwanted files. You may loose some App related data, but that is a small price to pay to fix your bricked phone.

If this method does not boot up your brick smartphone and the problem still persists, there are two more things you can try. Read ahead to find out about them.

Part 3: Booting straight into recovery mode

If your bricked phone does not boot up to your Home Screen or Lock screen and instead boots directly into Recovery Mode, there is not much left to do. Booting straight into recovery mode is undoubtedly a soft brick error but it also indicates a possible problem with your current ROM. The only option you have to flash a new ROM to reboot your bricked phone back to its normal functioning.

To flash a new ROM:

Firstly, you must root your phone and unlock the Bootloader. Every phone’s mechanism to unlock the bootloader is different, thus, we suggest to refer to your user manual.

Once the Bootloader is unlocked, take a backup of all your data by selecting “Backup” or “Android” back in recovery mode. The process should not take long and all you need to do is tap “OK” to config backup.

In this step, download a ROM of your choice and store it in your SD Card. Insert the SD Card in your phone to begin the flashing process.

Once at the recovery mode, select “Install Zip from SD Card” from the options.

Scroll down using the volume key and use the power key to select the downloaded ROM.

This might take a few minutes of your time, but once the process is complete, reboot your phone.

Hopefully, your bricked phone will not boot normally and work smoothly.

Part 4: Booting straight into Bootloader

If your bricked phone boots straight into Bootloader, then this a serious issue and must not be taken lightly. Flashing a new ROM or clearing cache partitions are of little help in such a brick smartphone situation. Booting straight into Bootloader is a peculiar soft bricked Android phone feature and can be tackled only by downloading and flashing your original ROM from the manufacturer. In order to do so, a detailed study about your manufacturer’s ROM, ways to download and flash must be carried out. Since different Android phones come with different types of ROMs, it difficult to cover all the aspects about the different types of ROMs.

Brick smartphone problem has become more prominent than phone freezing or hanging issue. Android users are often seen looking for solutions to fix their soft brick and hard brick phones. Android phones are prone to get bricked and thus, it is important for us to know about the three techniques given above. These methods have been tried, tested and recommended by ay affected bricked phone users. Therefore, these tips are reliable and worth a try. So if your phone acts stubborn and refuses to boot normally, examine the problem carefully and adopt one of the solutions given above which best suits your situation.

Bricked Your Xiaomi Redmi 13C? Here’s A Full Solution

A bricked phone is a device that won’t turn on no matter what you do and everything you try to do to fix it doesn’t work. Most people will tell you that there is really nothing you can do to fix a bricked device. But with the right information, the right buttons to push and useful additional software you can actually try to fix a bricked device.

In this article we are going to look at how you can fix your device if you are sure it is bricked, how to rescue the data on your bricked device and even how you can avoid this situation in the future.

Part 1: Rescue the data on your Bricked Android Phone

Before we can learn how to fix a bricked device, it is important that you are able to save the data that is on the Xiaomi Redmi 13C device. Having the data saved somewhere else will be the added insurance you need in case anything goes wrong during the process. There are very few software solutions in the market to help you get back data from a bricked device. One of these and the most reliable is Wondershare Dr.Fone - Data Recovery (Android) .

Dr.Fone - Data Recovery (Android)

World’s 1st Android smartphone and tablet recovery software.

• Recover data from broken Android in different situations.
• Scan and preview files before starting the retrieval process.
• SD card recovery on any Android devices.
• Recover contacts, messages, photos, call logs, etc.
• It works great with any Android devices.
• 100% safe to use.

4,771,974 people have downloaded it

How to Use Dr.Fone - Data Recovery (Android) to Rescue Data from a Bricked Android

If your device is completely unresponsive, don’t worry Dr.Fone can help you get all the data back. Simply follow these steps to gain access to the Xiaomi Redmi 13C device and recover all your data.

Step 1: Download and install Wondershare Dr.Fone to your PC. Launch the program and then click on Data Recovery. Select the data types you would like to recover and then click on Next.

Step 2. Select the issue type for your phone. Choose from “Touch screen not responsive or cannot access the phone” or “Black/broken screen”.

Step 3: In the next step, you need to select your device model. If you don’t know the model of your device click on “How to check the Xiaomi Redmi 13C device model” to get help.

Step 4: The next screen will provide instructions on how to enter “Download mode.” Connect the Xiaomi Redmi 13C device to your PC once it is in “Download Mode”

Step 5: The program will begin an analysis of your device and then download the recovery package.

Step 6: Then Dr.Fone will display all the recoverable file types. You can click on the files to preview them. Select the ones you need and click on “Recover to Computer” to save them to your computer.

Part 2: How to Fix Your Bricked Android Phone

Android devices are usually very flexible in allowing users to flash ROM but sometimes an incorrect process can result in a bricked device. While there are few solutions to this problem, here are a few things you can do;

When the Xiaomi Redmi 13C device Boots Straight into Recovery

If the Xiaomi Redmi 13C device can boot to the recovery screen, you can find an alternative ROM to install and copy it your device. Installation can then be done in the recovery menu. If the Xiaomi Redmi 13C device is booting to recovery mode there is a chance that it can be fixed.

Step 1: Load up Clockworkmod or any other recovery tool that you have been using.

Step 2: Once you are in, navigate to the “Reboot system now.” If you are using Clockworkmod, this should be your first option. Hopefully everything will work just right if you do this, If it doesn’t you may need to download and re-flash the ROM again.

When the Xiaomi Redmi 13C device won’t stop rebooting

Here’s what to do if the Xiaomi Redmi 13C device wont stop rebooting.

Step 1: Turn off the Xiaomi Redmi 13C device and then reboot in recovery mode.

Step 2: Go to “Advanced” which will bring up a number of options to choose from.

Step 3: One of the options should be “Wipe Dalvik cache” select this option and then follow the instructions. When finished select “Go Back” to return to the main menu.

Step 4: Go to the “Wipe Cache Partition” and select it.

Step 5: Go to “Wipe data/ factory reset.”

Step 6: Finally reboot the Xiaomi Redmi 13C device by selecting “Reboot system now.” This should fix the problem. You may also want to flash the same ROM or try a new one.

If the above methods don’t work, try one of the following options.

You can return to resource where you found the flash tools and search or ask for advice

Sometimes these errors can be caused if the ROM installation was performed via SD card. In this case reformatting the SD card might help.

If all else fails, it is time to returning the Xiaomi Redmi 13C device to the vendor if your warranty is still applicable.

Part 3: Useful Tips to avoid Bricking your Android Phone

If you are planning on installing custom ROM you need to install Custom Recovery. This will enable you restore the Xiaomi Redmi 13C device to its original settings should anything go wrong and hopefully help you avoid bricking your device.

1. Ensure that you are familiar with the Fastboot or ADB commands before doing anything. You should know how to recover your device by flashing a command line and also manually transfer important files to your device.
2. Make a backup of your device. This is obvious but most people fail to adhere to it. At the very least you can get back all your files and settings to transfer to a new phone.
3. Keep a full Nandroid backup on your phone
4. Keep another backup on your PC which you can access should anything go wrong with the Custom ROM installation
5. Know how to hard reset your device. It may come in handy when your device freezes on you.
6. You should also consider enabling USB debugging. This is because many solutions for a Bricked device rely on USB debugging.
7. Ensure the Custom ROM you choose can actually be used on your device model.

While installing Custom ROM can actually be a great way to customize your device, it is also the leading reason for bricked devices. Therefore ensure that you understand what you are doing when you decide to customize your device. Learn as much as you can about the process before attempting everything.

[8 Quick Fixes] Unfortunately, Snapchat has Stopped on Xiaomi Redmi 13C

Have you ever been deep in conversation with a loved one or friend, taking advantage of all the funny filters and games Snapchat has to offer when you’ve suddenly been presented with the ‘Unfortunately, Snapchat has Stopped’ error code? This is usually followed by the app crashing back to the main menu.

If so, don’t worry; you’re not alone. Snapchat crashing in this way is nothing new, but it can be incredibly annoying when it keeps happening and stops you from enjoying the conversations you care about.

Fortunately, there are plenty of solutions out there to help you out and get the app working again as it should do. Today, we’re going to explore them all to help you get back to what you were doing before and as though there was never a problem.

Part 1. Install Snapchat again from Google Play Store

One of the best ways to resolve the Snapchat crashing problem or Snap Map not working issue is to delete the app and reinstall it again. When you’re using your phone, there is data continually flowing around and data being sent here, there, and everywhere.

During these processes, bugs can occur, and if they can’t sort themselves out, the best thing to do is to reset your app and start from a fresh installation. Here’s how to do it.

Step 1: Hold down the Snapchat app from your main menu and press the ‘x’ button to uninstall the app.

Step 2: Open the Google App Store from your device and search ‘Snapchat’ in the search bar. Find the official app page and download the app onto your device.

Step 3: The app will automatically install itself once downloaded. Open the app, sign in to your account using your log-in details, and you should be able to use the app like normal.

Part 2. Check for new Snapchat Updates

Hand in hand with the problem above, sometimes a bug can restrict Snapchat from working, or perhaps your personal update settings. If you receive a Snapchat from someone with an upgraded version, this can crash your app.

Here’s how to make sure you’re running the latest version of Snapchat is Snapchat isn’t responding.

1. Launch the Play Store and navigate to the My Apps and Games page
2. Tap the Update button
3. The app will now automatically update to the latest version

Part 3. Wipe the cache of Snapchat

If you have a lot of data in your Snapchat cache, this can cause the app to become overloaded in which you’ll need to clear it to start again and refresh the app. This is a common problem that can cause Snapchat has stopped working error.

Here’s how to fix it.

1. Open the Snapchat app and tap the Profile icon on the top left-hand side of your screen

![wipe cahce of snapchat crashing - step 1](https://images.wondershare.com/drfone/article/2019/04/snapchat-cache-one.png)

2. Tap the Settings gear icon on the top right

   

3. Scroll down the Settings menu and tap the Clear Cache option

   

4. Here, you can choose to Clear All, but you can select individual areas if you prefer

   

5. Tap the Confirm option to clear your cache preference completely

   

Part 4. Fix the system issues that caused Snapchat stopping

If you’re experiencing the Snapchat crashing on Android often, or you’re experiencing similar errors with other apps, this can be an indication that there’s something wrong with your Android operating system.

The best way to fix this is to repair your device using the software known as Dr.Fone - System Repair (Android). This is a powerful repair system that can completely recover your device from any errors, including the Snapchat keeps crashing error.

Dr.Fone - System Repair (Android)

Dedicated repair tool to fix Snapchat crashing on Android.

• Recover your device from any problem, including black screen or unresponsive screen.
• Supports over 1000+ unique Android devices, models, and brands.
• Trusted by over 50+ million customers around the world.
• Can fully repair faults with your Xiaomi Redmi 13C’s firmware in a few simple steps.
• One of the most user-friendly applications in the world.

3,889,035 people have downloaded it

To help you make the most of this Android repair software and to fix your Snapchat not responding error, here’s a step-by-step guide on how to use it.

Step 1: Download the Dr.Fone - System Repair (Android) software to your computer. Install the software to your Mac or Windows computer by following the onscreen instructions.

Once completed, open the software, so you’re on the main menu.

Step 2: From the main menu, click the System Repair option, followed by the Android option. Of course, if you have an iOS device you want to repair in the future, the option is there if you want it. Also, connect your Xiaomi Redmi 13C to your computer using the USB cable.

Step 3: Confirm details.

On the next screen, use the drop-down menus to confirm the model, brand, operating system, and carrier of your device. Click Next to confirm the details are correct.

Step 4: You’ll now need to put your phone into Download Mode, sometimes referred to as Recovery Mode. For this, you can follow the onscreen instructions. Make sure your device stays connected to your computer throughout this process.

The method will slightly differ depending on whether your device has a home button, so make sure you follow the right instructions for your individual device.

Step 5: Once in Download Mode, the software will now download and install a fresh version of your Xiaomi Redmi 13C’s operating system. This can take some time, so make sure your device stays connected, and your computer stays on and doesn’t shut down.

Step 6: That’s it! Once you see the screen saying your device has been repaired, you’ll be able to close the Dr.Fone - System Repair (Android) software, disconnect your phone, and can start using Snapchat as normal without the Snapchat not responding error coming up!

safe & secure

Part 5. Check for the Android update

Similar to some of the other solutions we’ve listed above, if you’re using an outdated version of the Android operating system, but the latest version of Snapchat is coded to the most recent, this can be a cause for the Snapchat crashing on Android problem to occur.

Fortunately, it’s easy to check to make sure you’re running the latest version of Android and to download and install the update if you need it. Here’s how, which will help to sort out your Snapchat keeps crashing Android problems.

Step 1: Open the Settings menu on your Xiaomi Redmi 13C and select the About Phone option.

Step 2: Tap the ‘Check for Updates’ option. If an update is available, you’ll then have the option to Install Now or Install Overnight. If no update is available, you’ll see a notification stating your device is up to date and no action is needed.

Part 6. Connect to another Wi-Fi

In some cases, you may be trying to connect to a Wi-Fi network that’s not very stable. This may keep cutting the connection to your device, which in turn is causing Snapchat to crash on Android.

To resolve this, you can simply try connecting to another Wi-Fi network or a data plan to see whether this is the problem. If so, changing network and then using the Snapchat app should stop any error messages from occurring.

Step 1: Open the Settings menu on your Xiaomi Redmi 13C, followed by the Wi-Fi option.

Step 2: Tap the new Wi-Fi network you’re currently connected to, and then tap the ‘Forget’ option, to stop your phone connecting to it.

Step 3: Now tap the new Wi-Fi network you want to connect to. Insert the Wi-Fi security code and connect. Now try reopening and using the Snapchat to see if you can use it.

Part 7. Stop using the custom ROM

If you’re running a custom Android ROM on your device, with some versions of the ROM and some apps, you’re going to experience errors simply because of the way the apps and the ROMs are coded and designed.

Unfortunately, there’s no easy fix to this, and if you want to continue using the app, you’ll need to reflash your Xiaomi Redmi 13C back to its original firmware, and then wait until the ROM developers update the ROM to be compatible with social apps like Snapchat.

However, this reflashing process is simple thanks to the Dr.Fone - System Repair (Android) software that we listed above. To follow the detailed step-by-step guide, follow the steps on Part 4 of this article, or follow the quick guide instructions below.

1. Download and install the Dr.Fone - System Repair (Android) software to your computer
2. Connect your Xiaomi Redmi 13C to your Windows computer using the USB cable
3. Open the software and click the Repair option.
4. Select the Android device repair option
5. Make sure your carrier and device information are correct
6. Put your device into Download Mode by following the onscreen instructions
7. Allow the software to repair your Xiaomi Redmi 13C automatically

Part 8. Reset the factory settings of your Android

One of the last resorts you can take is factory resetting your Xiaomi Redmi 13C back to its original settings. From the day you first started using your device, you’ve been using the system and downloading files and apps, and over time this increases the chances of creating a bug.

However, by resetting your device to factory settings, you can reset these bugs and get your apps and device working again free from the Unfortunately, Snapchat has stopped error message. Here’s how to factory reset your device.

Make sure you back up your personal files from your device first like your photos and music files because factory resetting your device will clear your device’s memory.

Step 1: Tap the Settings menu on your device and click the Backup and Reset option.

Step 2: Click the Reset Phone option. That’s it! The phone will take several minutes to complete the process, after which your phone will be reset to its original state.