How to Fix the Soft Bricked Xiaomi Redmi A2+?

Bricked phone is a serious problem, as your brick smartphone could be suffering from a soft brick or hard brick problem, and must be dealt with carefully. It is very common to see a brick smartphone these days. If you are wondering what exactly is a bricked phone, here is your answer.

A bricked phone, hard brick or soft brick, is a smartphone which refuses to start or boot all the way up the home/main screen of the Xiaomi Redmi A2+ device. This issue is observed within most Android phones because users have a tendency to tamper with the Xiaomi Redmi A2+ device settings, flashing new and customized ROMs and tweaking with the essential files. Playing around with the phone’s internal set-up leads to such errors, worst of them being a brick smartphone. Usually, a bricked phone does not switch on and stays frozen at the Xiaomi Redmi A2+ device logo, a blank screen or even worse, doesn’t respond to any command, even the power on command.

If you are confused about the soft brick and hard brick problems and looking for solutions to fix your priced phone, then here is all you need to know.

Read on to find out more.

Part 1: What is the difference between soft brick and hard brick?

To begin with, let us understand the basic difference between a soft brick and hard brick issue. Both versions of a bricked phone prevent it from booting but differ in their causes and gravity of the problem.

A soft-brick problem is caused merely by a software error/crash and makes your device switch on automatically every time you manually turn it off. This phenomenon is referred to as Boot Loop. Soft bricked Android phones are not as difficult to fix as the hard bricked Android phones. It is convenient to say that a soft bricked phone only boots up half-way and not fully, whereas a hard bricked device does not switch on at all. A hard brick error is thus caused when the kernel, which is nothing but an interface for the software to communicate with the hardware, is tampered with. A hard bricked phone is not recognized by your PC when plugged in and is a serious problem. It requires troubleshooting techniques and cannot be easily fixed as the soft brick problem.

Hard bricked phones are a rare sight, but the soft brick is very common. Given below are ways to fix a soft brick Android phone. The techniques listed here are the best and the most efficient ways to get your phone back to its normal working conditions without losing your important data or damaging your device or its software.

Part 2: Stuck at the Boot Loop

This is the first sign of a soft bricked Android phone. Boot Loop is nothing but when your phone does not remain switched off and turns itself on automatically, and freezes at the logo screen or blank screen, every time you manually try to power it off.

Stuck at boot loop problem can be fixed by clearing your Cache partitions. These partitions are nothing but storage locations for your modem, kernels, system files, drivers and built-in Apps data.

It is advisable to clear Cache partitions regularly to keep your phone free from such glitches.

Since the phone refuses to boot, Cache can be cleared from entering into the Recovery Mode. Different Android devices have different ways to put it in recovery mode. Normally pressing the power key and volume down key helps, but you may refer to your phone’s guide for better understanding and then follow the steps given below to clear the cache partition:

Once you are the recovery mode screen, you will see a number of options as shown in the screenshot.

Use the volume down key to scroll down and select ”Wipe cache partition” as shown below.

>

After the process is completed, select “Reboot System” which is the first option in the recovery mode screen.

This method will help you erase all the clogged up and unwanted files. You may loose some App related data, but that is a small price to pay to fix your bricked phone.

If this method does not boot up your brick smartphone and the problem still persists, there are two more things you can try. Read ahead to find out about them.

Part 3: Booting straight into recovery mode

If your bricked phone does not boot up to your Home Screen or Lock screen and instead boots directly into Recovery Mode, there is not much left to do. Booting straight into recovery mode is undoubtedly a soft brick error but it also indicates a possible problem with your current ROM. The only option you have to flash a new ROM to reboot your bricked phone back to its normal functioning.

To flash a new ROM:

Firstly, you must root your phone and unlock the Bootloader. Every phone’s mechanism to unlock the bootloader is different, thus, we suggest to refer to your user manual.

Once the Bootloader is unlocked, take a backup of all your data by selecting “Backup” or “Android” back in recovery mode. The process should not take long and all you need to do is tap “OK” to config backup.

In this step, download a ROM of your choice and store it in your SD Card. Insert the SD Card in your phone to begin the flashing process.

Once at the recovery mode, select “Install Zip from SD Card” from the options.

Scroll down using the volume key and use the power key to select the downloaded ROM.

This might take a few minutes of your time, but once the process is complete, reboot your phone.

Hopefully, your bricked phone will not boot normally and work smoothly.

Part 4: Booting straight into Bootloader

If your bricked phone boots straight into Bootloader, then this a serious issue and must not be taken lightly. Flashing a new ROM or clearing cache partitions are of little help in such a brick smartphone situation. Booting straight into Bootloader is a peculiar soft bricked Android phone feature and can be tackled only by downloading and flashing your original ROM from the manufacturer. In order to do so, a detailed study about your manufacturer’s ROM, ways to download and flash must be carried out. Since different Android phones come with different types of ROMs, it difficult to cover all the aspects about the different types of ROMs.

Brick smartphone problem has become more prominent than phone freezing or hanging issue. Android users are often seen looking for solutions to fix their soft brick and hard brick phones. Android phones are prone to get bricked and thus, it is important for us to know about the three techniques given above. These methods have been tried, tested and recommended by ay affected bricked phone users. Therefore, these tips are reliable and worth a try. So if your phone acts stubborn and refuses to boot normally, examine the problem carefully and adopt one of the solutions given above which best suits your situation.

Xiaomi Redmi A2+ Bootloop Problem, How to Fix it Without Data Loss

Have you, like many other users, faced the bootloop Android problem and wondered what exactly is Android boot loop. Well, Android boot loop is nothing but an error that makes your phone switch on itself every time you manually turn it off. To be precise, when your Xiaomi Redmi A2+ does not remain switched off or powered off and starts to boot up automatically after a few seconds, it might be stuck in the boot loop Android.

An Android boot loop is a very common problem and is one of the first symptoms of a soft-bricked device. Also, when your device is experiencing Android boot loop issue, it does not start normally to reach the Home or Locked Screen and remains frozen at the Xiaomi Redmi A2+ device’s logo, Recovery Mode or a lit-up screen. Many people fear losing their data and other files due to this error and thus, it is a very confusing situation to be in.

We understand the inconvenience caused, therefore, here are ways to tell you how to fix the bootloop problem in Android devices without losing any important data.

However, before moving on, let us learn a little about the causes for the Android boot loop error.

Part 1: What might cause the bootloop issue on Android?

Android boot loop error might seem weird and unexplainable but it occurs because of some specific reasons.

Firstly, please understand that it is a misnomer that boot loop error occurs only in a rooted device. Boot loop Android error can also occur in a stock device with the original software, ROM, and firmware.

In a rooted device, changes made, such as flashing a new ROM or customized firmware which are not compatible with the Xiaomi Redmi A2+ device’s hardware or existing software, can be blamed for the boot loop problem.

Moving on, when your device’s software is unable to communicate with the system files during the start-up process, Android boot loop problem may arise. Such a glitch is caused if you have recently updated the Android version.

Also, corrupt App update files may also cause the bootloop Android issue. Apps and programs downloaded from unknown sources bring in a particular type of virus that prevents you from using your device smoothly.

All-in-all, Android boot loop error is a direct outcome of when you try to tamper with your device’s internal settings.

Hence, if you are looking for ways to guide you about how to fix boot loop issue, you will have to revamp the Xiaomi Redmi A2+ device internally by either resetting it or adopting a recovery method.

Read on to know more about how to fix the bootloop error without any data loss when your device suffers from the bootloop Android problem.

Part 2: One click to Fix Android Bootloop without factory reset

If you are trying to figure out how to fix boot loop, the first option you have is the one-click fix to Android Bootloop which involves using the Dr.Fone - System Repair software.

This is designed to repair any data corruption on your device and restores your firmware to its usual working condition.

Dr.Fone - System Repair (Android)

One click to fix boot loop of Android

• #1 Android repair solution from your PC, can fix a wide range of Android system issues, such as boot loop, black screen, etc.
• The software requires no technical expertise, and anybody can use it
• A one-click solution when learning how to fix Android boot loop
• Not require root Android phones.
• Works with most Xiaomi Redmi A2+ devices, including the latest Xiaomi Redmi A2+ phones like S22
• Simple and easy-to-use user interface

4,689,059 people have downloaded it

To help you get started, here’s a step-by-step guide on how to use Dr.Fone - System Repair.

Note: This method can erase data on your device, including your personal files, so make sure you’ve backed up your device before proceeding.

Step #1 Download the Dr.Fone - System Repair software from the website and install it onto your computer.

Open the software and select the System Repair option from the main menu to fix the Android bootloop error.

Step #2 Connect your Xiaomi Redmi A2+ to your computer using the official cable and select the “Android” option from the three menu items. Click “Start” to confirm.

You’ll then need to input the Xiaomi Redmi A2+ device information, such as your carrier info, device name, model, and country/region in order to ensure you’re downloading and repairing the correct firmware to your phone.

Step #3 Now you’ll need to put your phone into Download Mode to remove the Android bootloop.

For this, you can simply follow the onscreen instructions for both phones with and without home buttons.

Click “Next”, and the software will begin downloading the firmware repair files.

Step #4 Now you can sit back and watch the magic happen!

Make sure your computer stays connected to the internet, and your device stays connected to your computer throughout the entire process. Once the firmware has been downloaded, it will be automatically installed onto your mobile device, removing the boot loop Android error.

You’ll be notified when the process is done and when you can remove your device and start using free from the boot loop Android error!

safe & secure

Part 3: Soft reset to fix Android bootloop issue

When your device is stuck in Android boot loop, it does not necessarily mean that it is bricked. Boot loop might be occurring due to a simpler problem which can be fixed by turning off your device. This sounds like a home remedy for a serious problem but it works and resolves the problem most of the time.

Follow the steps given below to soft reset your device:

Turn the Xiaomi Redmi A2+ device off and take out its battery.

If you cannot take the battery out, let the phone be off for about 3 to 5 minutes, and then turn it back on.

Simply performing a soft reset on your device can help you if you are looking for solutions for how to fix the bootloop issue. This a very useful method as it does not result in any kind of loss in data and protects all your media files, documents, settings, etc.

In case the Xiaomi Redmi A2+ device does not turn on normally and is still stuck in the bootloop Android problem, be prepared to use the troubleshooting techniques given and explained below.

Part 4: Boot into Safe Mode to fix Android boot loop

Booting your Xiaomi Redmi A2+ into Safe Mode is a useful troubleshooting step to fix boot loop issues caused by third-party apps. When in Safe Mode, the Xiaomi Redmi A2+ device will start up with only essential system apps, and any downloaded apps that might be causing conflicts won’t run. Here’s how you can boot your Xiaomi Redmi A2+ into Safe Mode to address the boot loop problem:

Step 1: Power Off Your Device

Hold down the power button until it turns off completely.

Step 2: Access Safe Mode

To enter Safe Mode, follow these steps based on your device model:

• For most Android devices: Press and hold the power button to turn on your device. As soon as the manufacturer’s logo appears, press and hold the Volume Down button until the Xiaomi Redmi A2+ device finishes booting. You should see “Safe Mode” displayed in the bottom left or right corner of the screen.
• Some devices might require slightly different key combinations. Refer to your device’s user manual or perform an online search for the specific method to enter Safe Mode for your model.

Step 3: Observe the Xiaomi Redmi A2+ device

Once your device has booted into Safe Mode, use it for a while to see if the boot loop issue persists. If the boot loop doesn’t occur in Safe Mode, it indicates that the problem is likely caused by a third-party app.

Step 4: Identify and Uninstall Problematic Apps

Now that you’re in Safe Mode, it’s time to identify the troublesome app. Start by uninstalling recently installed apps one by one until the boot loop problem is resolved. After each uninstallation, restart your device normally to check if the boot loop still occurs. Continue this process until you find the problematic app.

Step 5: Restart Normally

Once you’ve identified and uninstalled the problematic app, restart your device normally to exit Safe Mode. Your Android device should now start up without getting stuck in a boot loop.

By following these steps and using Safe Mode to isolate problematic apps, you can effectively troubleshoot and resolve boot loop issues on your Xiaomi Redmi A2+.

Part 4: Factory reset to fix Android bootloop issue

Factory reset, also known as Hard Reset, is a one-stop solution for all your software resulting in issues. Android boot loop being such problem, can be easily overcome by performing a factory reset.

Please note that all your device’s data and settings will be deleted by adopting this method. However, if you have a Google account signed in on your Xiaomi Redmi A2+, you will be able to retrieve most of your data once the Xiaomi Redmi A2+ device turns on.

To factory reset your Android boot loop device, you must first boot into the Recovery Mode screen.

To do this:

Press the volume down button and power button together until you see a screen with multiple options before you.

Click here


When you are at the Recovery Mode screen, scroll down using the volume down key, and from the options given, select “Factory Reset” using the power key.

Wait for your device to perform the task and then:

Reboot the phone in Recovery Mode by selecting the first option.

This solution is known to fix the boot loop error 9 out of 10 times, but if you still can’t start your Xiaomi Redmi A2+ normally, consider using a CWM Recovery to resolve the Android boot loop issue.

Part 5: Use CWM Recovery to fix bootloop on rooted Android

CWM stands for ClockworkMod and it is a very popular custom recovery system. To use this system to solve the boot loop Android error, your Xiaomi Redmi A2+ must be rooted with CWM Recovery System which basically means CWM must be downloaded and installed on your device.

Furthermore, to use CWM Recovery to fix boot loop on rooted Android devices, follow the steps given below:

Press the home, power, and volume up buttons to launch the CWM Recovery screen.

Note: you might have to use a different combination of keys to enter into Recovery Mode, depending on your device’s model.

Scroll down using” the volume key to select “Advanced”.

Now select “Wipe” and choose to wipe “Dalvik Cache”.

In this step, select “Mounts and Storage” to click on “Wipe” or “Cache”.

Once this is done, make sure to reboot your Xiaomi Redmi A2+.

This process with successfully fix the Android boot loop error and not cause any loss of data stored on your device stuck in boot loop.

So the bottom line is that boot loop Android issue may seem like an irreparable error but it can be resolved by carefully following the techniques explained above. These methods not only tell you how to fix the bootloop problem but also prevent it from occurring in the future.

An Android boot loop is a common phenomenon with all Android devices because we tend to tamper with our device’s internal settings. Once the ROM, firmware, kernel, etc are damaged or rendered incompatible with the Xiaomi Redmi A2+ device’s software, you cannot expect it to function smoothly, hence, the boot loop error occurs. Since you are not the only one suffering from the Android boot loop problem, be rest assured that the ways, given above, to combat it are recommended by users facing similar troubles. So, don’t hesitate and go ahead to try them on.

safe & secure

Troubleshooting Guide: How to Fix an Unresponsive Xiaomi Redmi A2+ Screen

Smart devices have become an integral part of our lives, and Xiaomi Redmi A2+ phones are increasingly popular due to their advanced features and affordable prices. These phones offer numerous benefits, including high-quality cameras, fast processors, long-lasting batteries, and sleek designs.

However, like any other electronic device, Xiaomi Redmi A2+ phones can sometimes encounter issues that may impede their functionality. One common problem that users face is an unresponsive screen, which can be frustrating and disruptive to daily activities.

This article will discuss some valuable solutions for dealing with Xiaomi Redmi A2+ phone screen unresponsiveness. We will provide step-by-step instructions for troubleshooting and getting your phone back in working order. Whether you’re a novice or an experienced user, these tips and tricks will help you navigate this problem and get back to using your phone without any issues. So, let’s dive in and explore how to fix a Xiaomi Redmi A2+ phone with an unresponsive screen.

What causes the Xiaomi Redmi A2+ Screen unresponsive?

The Xiaomi Redmi A2+ screen may become unresponsive due to various reasons. Here are some common situations and their possible causes:

• During Use/Gaming: The screen may become unresponsive due to overheating when using or gaming on a Xiaomi Redmi A2+ phone. This can be caused by running too many apps simultaneously or playing games for an extended period, especially on models such as the Xiaomi Redmi A2+ 9 Pro, which generates much heat during gaming.

• **No Response When Touching the Screen:**Sometimes, the Xiaomi Redmi A2+ screen may not respond when touched due to a faulty touch screen or display. This can happen due to physical damage or a manufacturing defect. Some Xiaomi Redmi A2+ Nord 2 users have reported this issue.

• After Dropping the Phone: If a Xiaomi Redmi A2+ phone has been dropped, the screen may become unresponsive due to physical damage or a loose connection. This can happen to any model, including the Xiaomi Redmi A2+.

Overheating, physical damage, and manufacturing defects are some common causes of Xiaomi Redmi A2+ screen unresponsiveness, which may occur during use/gaming, no response when touching the screen, or after dropping the phone.

The common solutions to solve a Xiaomi Redmi A2+ Screen unresponsive

Here are the three most common solutions to deal with phone screens being unresponsive, regardless of the brand:

Restart the Xiaomi Redmi A2+ device

Restarting the Xiaomi Redmi A2+ device is a simple and quick solution to an unresponsive phone screen. To restart the phone, press and hold the power button until the screen turns off, then press and hold the power button again to turn the phone back on.

Check the Charging Port and Battery

Sometimes, an unresponsive screen can be caused by a dead battery or a faulty charging port. To check for these issues:

Step 1: Plug the phone into a charger and wait for at least 30 minutes to see if the battery charges.

Step 2: Try a different charger or cable to see if the issue is with the charging accessories.

Contact the Pros

If the above solutions don’t work, contacting a professional is best. A trained technician can diagnose and fix the problem. Contact the phone manufacturer or an authorized repair center to get help with your phone.

For different Xiaomi Redmi A2+ models, there may be additional solutions to consider:

Check the Phone’s Temperature

Sometimes, a Xiaomi Redmi A2+ phone’s screen, specifically Xiaomi Redmi A2+ 8 Pro, may become unresponsive due to overheating. To check the phone’s temperature:

Step 1: Go to Settings > Battery > Battery Temperature.

Step 2: If the phone is overheating, let it cool down before using it again.

Reset to Factory Settings

A factory reset may help fix the problem if none of the above solutions work. Note that this will erase all data and settings on the phone, so be sure to back up your data before resetting. To reset the phone:

Step 1: Go to Settings > Additional Settings > Backup and Reset > Erase All Data.

Step 2: Follow the on-screen instructions to reset the phone.

Replace a New Screen

If the phone’s screen is physically damaged or cracked, it may need to be replaced. To replace the screen:

• Contact a professional repair center or the manufacturer for replacement parts and installation.

How to avoid Xiaomi Redmi A2+ Screen being unresponsive?

To avoid Xiaomi Redmi A2+ screen being unresponsive, here are some suggestions based on the possible causes:

Check Software Updates on Time

Make sure to regularly check for and install software updates on your Xiaomi Redmi A2+ phone. These updates often include bug fixes and security patches that can help prevent issues like overheating and screen unresponsiveness.

Check Hardware from Time to Time

Regularly inspect your phone’s hardware components such as charging ports, battery, and screen for any signs of damage or wear and tear. If you notice any issues, get them fixed promptly to prevent them from causing further damage.

Avoid extreme temperatures

Keep your Xiaomi Redmi A2+ device in a temperature-controlled environment. High temperatures can cause the screen to become unresponsive, and low temperatures can cause it to freeze.

Keep the screen clean

Dirt and debris on the screen can cause it to become unresponsive. Use a microfiber cloth to clean the screen regularly.

Reduce the number of running apps

Running too many apps at once can overload the system and cause the screen to become unresponsive. Close any apps you’re not using to free up system resources.

Use Wondershare Dr.Fone to Repair or Manage Your Data

Wondershare Dr.Fone is a helpful tool that can help manage and repair your phone’s data. It can be used to back up your data, transfer files between devices, and even fix issues like an unresponsive screen. Dr.Fone has the DF13 version to be launched, which includes more features to help manage your phone’s data effectively.

By following these suggestions, you can help prevent screen unresponsiveness on your Xiaomi Redmi A2+ phone. Download Dr.Fone at https://drfone.wondershare.com/ to manage your phone’s data effectively and fix any issues that may arise.

safe & secure

Conclusion

Xiaomi Redmi A2+ phones offer numerous benefits, including high-quality cameras, fast processors, long-lasting batteries, and sleek designs. However, like any other electronic device, Xiaomi Redmi A2+ phones can sometimes encounter issues, such as an unresponsive screen. The causes of an unresponsive screen may include overheating, physical damage, and manufacturing defects.

To deal with an unresponsive screen, users can try restarting the Xiaomi Redmi A2+ device, checking the charging port and battery, or contacting a professional. Additional solutions for specific Xiaomi Redmi A2+ models include checking the phone’s temperature, resetting to factory settings, or replacing a new screen. To avoid an unresponsive screen, users can check software updates on time, inspect the phone’s hardware, avoid extreme temperatures, keep the screen clean, and reduce the number of running apps. Dr.Fone is a helpful tool that can help manage and repair your phone’s data.