How to Fix the Soft Bricked ZTE Blade A73 5G?

Bricked phone is a serious problem, as your brick smartphone could be suffering from a soft brick or hard brick problem, and must be dealt with carefully. It is very common to see a brick smartphone these days. If you are wondering what exactly is a bricked phone, here is your answer.

A bricked phone, hard brick or soft brick, is a smartphone which refuses to start or boot all the way up the home/main screen of the ZTE Blade A73 5G device. This issue is observed within most Android phones because users have a tendency to tamper with the ZTE Blade A73 5G device settings, flashing new and customized ROMs and tweaking with the essential files. Playing around with the phone’s internal set-up leads to such errors, worst of them being a brick smartphone. Usually, a bricked phone does not switch on and stays frozen at the ZTE Blade A73 5G device logo, a blank screen or even worse, doesn’t respond to any command, even the power on command.

If you are confused about the soft brick and hard brick problems and looking for solutions to fix your priced phone, then here is all you need to know.

Read on to find out more.

Part 1: What is the difference between soft brick and hard brick?

To begin with, let us understand the basic difference between a soft brick and hard brick issue. Both versions of a bricked phone prevent it from booting but differ in their causes and gravity of the problem.

A soft-brick problem is caused merely by a software error/crash and makes your device switch on automatically every time you manually turn it off. This phenomenon is referred to as Boot Loop. Soft bricked Android phones are not as difficult to fix as the hard bricked Android phones. It is convenient to say that a soft bricked phone only boots up half-way and not fully, whereas a hard bricked device does not switch on at all. A hard brick error is thus caused when the kernel, which is nothing but an interface for the software to communicate with the hardware, is tampered with. A hard bricked phone is not recognized by your PC when plugged in and is a serious problem. It requires troubleshooting techniques and cannot be easily fixed as the soft brick problem.

hard bricked v/s soft bricked

Hard bricked phones are a rare sight, but the soft brick is very common. Given below are ways to fix a soft brick Android phone. The techniques listed here are the best and the most efficient ways to get your phone back to its normal working conditions without losing your important data or damaging your device or its software.

Part 2: Stuck at the Boot Loop

This is the first sign of a soft bricked Android phone. Boot Loop is nothing but when your phone does not remain switched off and turns itself on automatically, and freezes at the logo screen or blank screen, every time you manually try to power it off.

Stuck at boot loop problem can be fixed by clearing your Cache partitions. These partitions are nothing but storage locations for your modem, kernels, system files, drivers and built-in Apps data.

It is advisable to clear Cache partitions regularly to keep your phone free from such glitches.

Since the phone refuses to boot, Cache can be cleared from entering into the Recovery Mode. Different Android devices have different ways to put it in recovery mode. Normally pressing the power key and volume down key helps, but you may refer to your phone’s guide for better understanding and then follow the steps given below to clear the cache partition:

Once you are the recovery mode screen, you will see a number of options as shown in the screenshot.

Use the volume down key to scroll down and select ”Wipe cache partition” as shown below.

After the process is completed, select “Reboot System” which is the first option in the recovery mode screen.

This method will help you erase all the clogged up and unwanted files. You may loose some App related data, but that is a small price to pay to fix your bricked phone.

If this method does not boot up your brick smartphone and the problem still persists, there are two more things you can try. Read ahead to find out about them.

Part 3: Booting straight into recovery mode

If your bricked phone does not boot up to your Home Screen or Lock screen and instead boots directly into Recovery Mode, there is not much left to do. Booting straight into recovery mode is undoubtedly a soft brick error but it also indicates a possible problem with your current ROM. The only option you have to flash a new ROM to reboot your bricked phone back to its normal functioning.

To flash a new ROM:

Firstly, you must root your phone and unlock the Bootloader. Every phone’s mechanism to unlock the bootloader is different, thus, we suggest to refer to your user manual.

Once the Bootloader is unlocked, take a backup of all your data by selecting “Backup” or “Android” back in recovery mode. The process should not take long and all you need to do is tap “OK” to config backup.

In this step, download a ROM of your choice and store it in your SD Card. Insert the SD Card in your phone to begin the flashing process.

Once at the recovery mode, select “Install Zip from SD Card” from the options.

Scroll down using the volume key and use the power key to select the downloaded ROM.

This might take a few minutes of your time, but once the process is complete, reboot your phone.

Hopefully, your bricked phone will not boot normally and work smoothly.

Part 4: Booting straight into Bootloader

If your bricked phone boots straight into Bootloader, then this a serious issue and must not be taken lightly. Flashing a new ROM or clearing cache partitions are of little help in such a brick smartphone situation. Booting straight into Bootloader is a peculiar soft bricked Android phone feature and can be tackled only by downloading and flashing your original ROM from the manufacturer. In order to do so, a detailed study about your manufacturer’s ROM, ways to download and flash must be carried out. Since different Android phones come with different types of ROMs, it difficult to cover all the aspects about the different types of ROMs.

Brick smartphone problem has become more prominent than phone freezing or hanging issue. Android users are often seen looking for solutions to fix their soft brick and hard brick phones. Android phones are prone to get bricked and thus, it is important for us to know about the three techniques given above. These methods have been tried, tested and recommended by ay affected bricked phone users. Therefore, these tips are reliable and worth a try. So if your phone acts stubborn and refuses to boot normally, examine the problem carefully and adopt one of the solutions given above which best suits your situation.

Reasons for ZTE Blade A73 5G Stuck on Startup Screen and Ways To Fix Them

There are many reasons why phones get stuck on the boot screen. It could be something as simple as physical damage or more complicated related to software problems. Having your phone stuck on the logo screen, or boot screen is annoying, and it is no surprise that people will find ways to fix this issue when encountered.

This article will share the possible reasons why your phone is stuck on the boot screen. This article will share three possible reasons for this problem and three valuable tips to help fix this issue. If all else fails, there is an application that is recommended and is sure to solve your issue in no time. Keep on reading to find out more!

It is not uncommon for phones to be stuck on the startup screen, but finding out why this happens is tricky. This section identified some of the top reasons your cellphone could have gotten stuck on the startup screen.

Physical Damage to the Phone

If you accidentally dropped your phone or knocked it on a hard surface, you could have damaged the internal hardware of your phone. This could affect your phone’s ability to reboot and result in your phone being stuck on the boot screen.

If you are 100% certain that your phone has gone through physical damage, you should seek professional help to have your phone repaired or checked. It is advised not to fix this problem yourself as your phone’s internal parts are complicated and delicate. Look for an official phone repair store and get your phone fixed for issues like your phone getting stuck on the logo.

Parental Control Software

#1 Rated Parental Control Software.
Monitor & Control all PC Activity!
sentrypc.com/parental-controls/ ### Liquid Damage

It is not common for your phone to expose to water. Rain or water splashes are unavoidable; sometimes, your phone gets wet. Little exposure to water on the surfaces of your phone is fine. However, if you fall into a pool with your phone or drop it in a puddle of water, your phone will likely suffer from liquid damage.

Even the tiniest water droplet that seeped into your phone could damage the internal hardware of your device, often leaving you with your phone stuck on the boot screen. The first thing to do when you accidentally submerge your phone in the water is to check if the water has damaged your phone.

For iPhone users, look for the water damage indicator. If you see that it has turned from white to red, it has suffered from water damage. You have two options if your phone has suffered liquid damage. One is dismantling your phone and letting it dry for at least 48 hours. Two is bringing your phone to a repair shop to fix it.

Software Issues

Software issues are probably the most common reason your phone is stuck on the logo screen. Eight times out of ten, software issues are either caused by a failed software update, using an older version of the operating system, or having a jailbroken phone. When the software does not successfully update, the phone will have no operating system, as the old system was erased before the new software was installed.

The older operating system is also not desired as your phone typically will send periodic updates to make sure your phone is up-to-date and free from bugs. Running applications on an older operating system might lead to issues like the phone being stuck on the boot screen or the logo. Hence, updating your phone to the latest software version would be better.

Part 2. 3 Helpful Ways To Fix Phones Stuck on Boot Screen

After understanding the common problems on why your phone is stuck on the startup screen page, here are three easy solutions to try solving yourself at home.

Hard reboot your phone

To quickly fix any of your phone issues, especially when stuck on the startup screen, perform a hard reboot. The term hard reboot means turning your device off and on again. You might think this is a simple option, but this is a tried and tested method that might work on a minor glitch that results in your smartphone getting stuck on the startup screen page.

Here is an example of performing a hard reboot for an Android phone such as ZTE Blade A73 5G. Preess and hold the Power and Volume Down buttons simultaneously for more than 7 seconds to perform the hard reboot.

Put your phone in recovery mode

If a hard reboot does not work, a natural next step is to try going into recovery mode. The recovery mode is specially designed to solve any software-related issues. It is important to note that entering recovery mode will delete all your corrupted files and replace them with a functional operating system. Hence, back up all your files to ensure you retain all your information.

Here is a step-by-step process for putting your ZTE Blade A73 5G or Redmi smartphone in recovery mode.

Step 1: Tap and press the Power button to switch off your ZTE Blade A73 5G/Redmi phone

Step 2:Hold the Volume Up and the Power buttons at the same time, then release the keys when the Main menu of Recovery mode appears on the screen.

Step 3: You can use the volumes buttons to navigate up and down and press the Power key to confirm the selection.

Factory Reset

If you do not want to attempt recovery mode, you can try resolving the issue of your phone being stuck on the startup screen through Factory Reset. Factory Reset, also called Hard Reset, erases all information and data on your device. As a result, it will return to the settings and recover the data it used to have when leaving the factory.

Here is an example of putting your Samsang smartphone into the Factory Reset DFU mode.

Step 1: Open the Settings application on your phone and tap General Management.

Step 2: Go to Reset > Factory data reset.

Step 3: Swipe to and tap Reset.

Note: Before carrying out a factory reset, you need to input the password of your ZTE Blade A73 5G Account.

Bonus Tip: Best App To Solve Phone Stuck on Boot Screen

If all the solutions above do not work and you do not want to perform a factory reset on your phone, one option is to use an application called Wondershare Dr.Fone. It is one of the most effective phone recovery solutions and can help to bring your phone back to a state like it was brand new. Being stuck on the startup screen page will be a problem of the past.

The following steps will show you how to use Dr.Fone to perform system repair on your phone.

Step 1: To the Dr.Fone application using the link above and click on System Repair.

Step 2: Depending on the ZTE Blade A73 5G device you are using, choose either Android or iPhone.

Step 3: In the next window, select the issue you are facing and click Start.

Step 4: Choose the corresponding Brand, Name, Model, Country, and Carrier from each drop-down menu and click Next.

Tip: Make sure the information you input is accurate, as it will affect the system repair if the information is inaccurate.

Step 5: Connect your device to your computer and follow the instructions on the screen to enter Download mode. Click on Next to proceed to the next step.

Step 6: Wait for the process to complete, and a new firmware will be updated on your device. Power on your phone and check if the issue still exists.

Frequently Asked Questions

The following are interesting and frequently asked questions about how to solve boot loops.

What is a boot loop?

A boot loop describes a process when Your ZTE Blade A73 5G stays stuck in a circle of rebooting. When your phone is stuck on the startup screen, one of the strategies you will try is to restart your device. However, when your phone gets stuck in a boot loop, it is your device’s way of trying to turn it off and on again to fix the issue.

Since there is an issue with the booting process, it will keep running into the same error repeatedly, calling the boot loop. When trapped in a boot loop, your device will keep turning off and on. Most boot loop issues are software-related, such as a wrong system update.

How do you fix a boot loop?

When stuck in a boot loop, there are different troubleshooting methods for other devices. For Android phones, force your phone into its Recovery mode; from there, you can restore a previous backup. This backup could be from when the boot loop did not exist, so recovery to that backup could quickly solve the problem.

For iPhones, it is the same concept as the Android, restore your phone to the previous backup. You can use iTunes to restore a previously stored backup on your computer.

How to prevent a boot loop?

A boot loop typically starts when there is a change to your system before a reboot cycle. Most issues are software-related, such as having to do a system upgrade gone wrong or a problem that doesn’t mesh. One way to prevent this is to perform a software or system upgrade constantly. Make your phone juiced to prevent it from turning off mid-way when updating.

safe & secure

3,405,439 people have downloaded it

Conclusion

This article summarizes some of the possible reasons why your phone is stuck on the boot screen. It demonstrated three useful strategies to overcome your phone stuck in the boot with ease. However, if all the above methods do not work, why not try Dr.Fone-System Repair?

Dr.Fone-System Repair repairs the operating system issues and fixes the issue with your phone. Once you power on your phone again, you can rest assured that it will be like new.

ZTE Blade A73 5G Not Connecting to Wi-Fi? 12 Quick Ways to Fix

Nowadays, it’s pretty much essential to have your ZTE Blade A73 5G or smartphone connected to the internet. Whether you’re watching videos, looking something up, or using any kind of app, you need the internet for these applications to function correctly.

This is why it can so annoying when it gets to a point where the internet connection isn’t working. However, the problem of a web page not loading correctly is just the tip of the iceberg.

There are plenty of problems you could experience, whether it’s the Wi-Fi network keeps disconnecting on its own without any warning, perhaps a security issue where the passcode or IP address isn’t being registered properly, or even if the connection is just being super slow, even if there’s no reason too.

Luckily, despite there being so many problems out there, there are also many solutions. Today, we’re going to share with you the complete definitive guide to help you get your ZTE Blade A73 5G connected and free from problems and issues.

Part 1: Restart your ZTE Blade A73 5G

Begin by powering off your ZTE Blade A73 5G and unplugging your router. Wait for about a minute before plugging in the router and turning on your device. This simple reset can often restore stable connections and fix Android wifi not working.

Part 2: Turn on Airplane mode and turn off

Turn on Airplane Mode for a few seconds, then turn it off. This maneuver refreshes your device’s network connections and might rectify the Android not connecting to wifi issue.

Part 3. Check Wi-Fi Router settings

The third step you’ll want to take is making sure the internet router in your house is working properly and is actually sending internet data to your ZTE Blade A73 5G. Of course, if you have other internet-enabled devices connected to the same router and they’re working fine, you know this isn’t the problem.

However, if you’ve got a problem with Wi-Fi not working on your Android and other devices in your home or office, you know you’ve got a router problem. Here’s how to solve it.

Go to your internet router and check the indicator lights
While this depends on your device, a green or blue light will mean the connection is good, whereas a red light indicates a problem
Press the Restart button on your router and wait ten minutes before reconnecting your device and connecting again
Call up your internet provider to see if there’s an internet connection issue in your area
Open your web browser and log into your router settings to ensure your ZTE Blade A73 5G is connected to the Wi-Fi network and is allowed to send and receive data

Part 4. Boot your Android in safe mode

If you’re unable to connect to the internet, but other devices have no issues, you may find the issues is coming from within your ZTE Blade A73 5G itself. Fortunately, there are ways you can see whether this is the problem.

The best way to do this is to boot your device in Safe Mode. The process for doing this will depend on the make and model of your ZTE Blade A73 5G, but the basic process goes as follows;

Turn off your ZTE Blade A73 5G by holding down the Power button and tapping Power Off. Wait a few minutes to ensure the ZTE Blade A73 5G device is completely off
Press and hold the Power button to turn your phone on, but the press and hold both the volume up and volume down buttons at the same time
You will see the words ‘Safe Mode’ appear on your screen as the ZTE Blade A73 5G device loads
Now you will be booted in Safe Mode. Try connecting to the internet again to see if it works

If your device connects to the internet while in Safe Mode, you’ll know you have a problem with an app or service that’s running on your device. If this is the case, you’ll need to go through your apps and delete them and then reinstall them one at a time until you find the app or service that is causing your internet problems.

Part 5. Check the Android Wi-Fi adapter

If you’re using a Wi-Fi adapter on your device to connect to the internet, you’ll need to make sure this is working. This could be an adapter on your ZTE Blade A73 5G itself, especially if you’re using an older device, or if you’re using an adapter to boost the ranger of your router network.

You need to check both of these to make sure your connection is working properly.

If using an Android Wi-Fi adapter, make sure all the ZTE Blade A73 5G device drivers are up to date, and if you’re using an app, make sure the app is updated, and all the settings allow an internet connection
If you’re using a router adapter, make sure it’s set up properly, and your ZTE Blade A73 5G is connected to the adapter using the correct passwords. Try connecting another device to see if the internet connection is working on there
Whichever method you’re using, try disconnecting your ZTE Blade A73 5G and forgetting the network, and then reconnecting and entering the right password to refresh the connection

Part 6. Check SSID and IP address on Android

To make a Wi-Fi connection work, your ZTE Blade A73 5G needs to match two codes that connect and relate to your router to establish the connection and work correctly. These are known as the SSID and the IP address.

Every wireless device will have its own codes and making sure they’re matched to the network you’re connecting to is crucial to ensuring the internet is working on your ZTE Blade A73 5G. Here’s how to check on your ZTE Blade A73 5G to make sure everything is correct.

Tap the Settings menu option, followed by Wi-Fi on your ZTE Blade A73 5G
Turn on your Wi-Fi network and connect it to your router
Find the router name (SSID) and make sure it’s exactly the same as the SSID written on your router
Once connected, tap the Wi-Fi network and you will see the IP address. Check both your phone and the router codes to make sure this number matches

When these numbers are matching, if your Android is still not connecting to wifi, you’ll know this wasn’t the problem.

Part 7. Fix Android system issues in one click

If none of the solutions above are working, this could indicate a real problem with the firmware and operating system of your ZTE Blade A73 5G. Fortunately, a fast solution to get everything working again is to completely repair the software of your phone.

You can do this easily using powerful Android recovery software known as Dr.Fone - System Repair (Android) . This is the leading repair tool on the market and is designed to fix and repair any firmware and software problems you may be having.

Dr.Fone - System Repair (Android)

A one-click tool to fix Wi-Fi not working on Android

Can repair Android from any problem including the black screen of death
A trusted software application used by 50+ million people around the world
The most user-friendly mobile repair application available right now
Supports over 1,000+ Android models and devices
A world-class customer support team to help you whenever you need them

3,483,527 people have downloaded it

To help you have the best and the most accurate experience when using the Dr.Fone - System Repair (Android) application, here’s a complete step-by-step guide on how to use it.

Step One Make your way over to the Wondershare website and download the Dr.Fone - System Repair (Android) software. Install it onto your computer by following the on-screen instructions.

Once installed, connect your ZTE Blade A73 5G to your computer using a USB cable, and open the software, click “System Repair”.

Step Two Click the “Android” option in the menu and then click “Start” to begin the Repair process.

Step Three On the next screen, go through the options and use the drop-down menus to make sure the information is correct for your individual device. Accept the terms and conditions of the software, and then click the “Next” button.

Step Four Confirm you want the software to carry out the repair process by typing the ‘000000’ code into the pop-up box and pressing Confirm. Make sure you read everything displayed in this box beforehand to know what’s happening.

Step Five Now put your phone into Download Mode by following the on-screen instructions, so your device is ready for the repair process. The method for getting your phone into Download Mode will vary depending on your device, so make sure you’re following the right instructions.

Step Six Once the software has detected your device in Download Mode, it will automatically begin the repair process. You need to make sure your device stays connected throughout this time, and your computer stays on.

The whole process is automatic, so you won’t need to do anything until it’s finished. Once completed, you can disconnect your phone and start connecting it to the internet as normal!

safe & secure

Part 8. Check the Wi-Fi connectivity on another phone

When experiencing problems with your Wi-Fi network, it’s worth noting the problem might not be with your phone, but rather the Wi-Fi network itself. This is why it’s important to make sure you check the connection on another device.

Of course, if you’re already using another phone on your Wi-Fi network, you know this isn’t the case. However, if you’re not sure, here’s what you need to do;

Get another Android or iOS phone or tablet
Open the Settings menu and connect to the Wi-Fi network you’re having problems with
Enter the password and connect to the network
Open a web browser on the phone and try loading a web page
If the page loads, you know the Wi-Fi network isn’t the problem
If the page doesn’t load, you know you’ve got a problem with your Wi-Fi network

Part 9. Change the password of the Wi-Fi

Each Wi-Fi network router will give the opportunity to choose and change the password you have to let devices connect to your network. It’s important you try changing this because you never know if someone else has accessed your network and could be blocking your device. Here’s how it works;

Log onto your computer and open your Wi-Fi settings
Depending on the brand and method of your individual router, navigate to the Wi-Fi password settings menu
Change the password to something complicated using all available digits and characters
Save the password and restart the router to disconnect all devices
Now connect your ZTE Blade A73 5G to the router using the new password

Part 10. Reset network settings on Android

Just like the method above where you’ll be effectively resetting the network settings on your router, if this hasn’t worked, you’ll be able to reset the network settings on your ZTE Blade A73 5G, hopefully removing the bugs and allowing you to connect.

Here’s how you can do this easily on your ZTE Blade A73 5G;

From the home screen of your ZTE Blade A73 5G, open the Settings menu
Tap the Backup & Reset option
Tap the Reset Network Settings option
Tap the Reset Network option
If you need to, enter the PIN number or passcode for the Android device, and the ZTE Blade A73 5G device will confirm the reset has taken place
Reconnect your ZTE Blade A73 5G to your Wi-Fi network for the changes to take effect

Part 11. Clear partition cache in recovery mode

As you continue to use your ZTE Blade A73 5G, the partition cache will fill up with data your device needs and doesn’t need. However, by clearing your device’s partition cache, you can make clear up some space which should help your device have enough memory to connect to the internet.

Turn off your ZTE Blade A73 5G
Turn it on by holding down the power button, volume button, and home button
When your phone vibrates, let go of the Power button, but continue to hold the volume button
When a menu is displayed, use the volume buttons to navigate the menu
Select the Android System Recovery option, followed by Wipe Cache Partition
Restart your device and connect to the internet

Part 12. Reset factory settings

If worse comes to worst, another option you have is to factory reset your ZTE Blade A73 5G. As we’ve spoken about above, while using your phone from the day you started using it, your device will fill up with files and data which can become messy and causes bugs.

However, by factory resetting your device, you can start again from the factory default from which you first received it, ultimately clearing the bugs. Make sure you back up your device before proceeding because it will erase your personal files.

Open the Settings menu on your ZTE Blade A73 5G
Navigate to System > Advanced > Reset Options
Tap the Reset phone option, and enter your PIN code if required
Tap Erase Everything
Wait for your phone to complete the process
Restart your device and connect to the internet

safe & secure

Fix Guide

How to Fix the Soft Bricked ZTE Blade A73 5G? | Dr.fone