Itel P40 Not Connecting to Wi-Fi? 12 Quick Ways to Fix

Nowadays, it’s pretty much essential to have your Itel P40 or smartphone connected to the internet. Whether you’re watching videos, looking something up, or using any kind of app, you need the internet for these applications to function correctly.

This is why it can so annoying when it gets to a point where the internet connection isn’t working. However, the problem of a web page not loading correctly is just the tip of the iceberg.

There are plenty of problems you could experience, whether it’s the Wi-Fi network keeps disconnecting on its own without any warning, perhaps a security issue where the passcode or IP address isn’t being registered properly, or even if the connection is just being super slow, even if there’s no reason too.

Luckily, despite there being so many problems out there, there are also many solutions. Today, we’re going to share with you the complete definitive guide to help you get your Itel P40 connected and free from problems and issues.

Part 1: Restart your Itel P40

Begin by powering off your Itel P40 and unplugging your router. Wait for about a minute before plugging in the router and turning on your device. This simple reset can often restore stable connections and fix Android wifi not working.

Part 2: Turn on Airplane mode and turn off

Turn on Airplane Mode for a few seconds, then turn it off. This maneuver refreshes your device’s network connections and might rectify the Android not connecting to wifi issue.

Part 3. Check Wi-Fi Router settings

The third step you’ll want to take is making sure the internet router in your house is working properly and is actually sending internet data to your Itel P40. Of course, if you have other internet-enabled devices connected to the same router and they’re working fine, you know this isn’t the problem.

However, if you’ve got a problem with Wi-Fi not working on your Android and other devices in your home or office, you know you’ve got a router problem. Here’s how to solve it.

Go to your internet router and check the indicator lights
While this depends on your device, a green or blue light will mean the connection is good, whereas a red light indicates a problem
Press the Restart button on your router and wait ten minutes before reconnecting your device and connecting again
Call up your internet provider to see if there’s an internet connection issue in your area
Open your web browser and log into your router settings to ensure your Itel P40 is connected to the Wi-Fi network and is allowed to send and receive data

Part 4. Boot your Android in safe mode

If you’re unable to connect to the internet, but other devices have no issues, you may find the issues is coming from within your Itel P40 itself. Fortunately, there are ways you can see whether this is the problem.

The best way to do this is to boot your device in Safe Mode. The process for doing this will depend on the make and model of your Itel P40, but the basic process goes as follows;

Turn off your Itel P40 by holding down the Power button and tapping Power Off. Wait a few minutes to ensure the Itel P40 device is completely off
Press and hold the Power button to turn your phone on, but the press and hold both the volume up and volume down buttons at the same time
You will see the words ‘Safe Mode’ appear on your screen as the Itel P40 device loads
Now you will be booted in Safe Mode. Try connecting to the internet again to see if it works

If your device connects to the internet while in Safe Mode, you’ll know you have a problem with an app or service that’s running on your device. If this is the case, you’ll need to go through your apps and delete them and then reinstall them one at a time until you find the app or service that is causing your internet problems.

Part 5. Check the Android Wi-Fi adapter

If you’re using a Wi-Fi adapter on your device to connect to the internet, you’ll need to make sure this is working. This could be an adapter on your Itel P40 itself, especially if you’re using an older device, or if you’re using an adapter to boost the ranger of your router network.

You need to check both of these to make sure your connection is working properly.

If using an Android Wi-Fi adapter, make sure all the Itel P40 device drivers are up to date, and if you’re using an app, make sure the app is updated, and all the settings allow an internet connection
If you’re using a router adapter, make sure it’s set up properly, and your Itel P40 is connected to the adapter using the correct passwords. Try connecting another device to see if the internet connection is working on there
Whichever method you’re using, try disconnecting your Itel P40 and forgetting the network, and then reconnecting and entering the right password to refresh the connection

Part 6. Check SSID and IP address on Android

To make a Wi-Fi connection work, your Itel P40 needs to match two codes that connect and relate to your router to establish the connection and work correctly. These are known as the SSID and the IP address.

Every wireless device will have its own codes and making sure they’re matched to the network you’re connecting to is crucial to ensuring the internet is working on your Itel P40. Here’s how to check on your Itel P40 to make sure everything is correct.

Tap the Settings menu option, followed by Wi-Fi on your Itel P40
Turn on your Wi-Fi network and connect it to your router
Find the router name (SSID) and make sure it’s exactly the same as the SSID written on your router
Once connected, tap the Wi-Fi network and you will see the IP address. Check both your phone and the router codes to make sure this number matches

When these numbers are matching, if your Android is still not connecting to wifi, you’ll know this wasn’t the problem.

Part 7. Fix Android system issues in one click

If none of the solutions above are working, this could indicate a real problem with the firmware and operating system of your Itel P40. Fortunately, a fast solution to get everything working again is to completely repair the software of your phone.

You can do this easily using powerful Android recovery software known as Dr.Fone - System Repair (Android) . This is the leading repair tool on the market and is designed to fix and repair any firmware and software problems you may be having.

Dr.Fone - System Repair (Android)

A one-click tool to fix Wi-Fi not working on Android

Can repair Android from any problem including the black screen of death
A trusted software application used by 50+ million people around the world
The most user-friendly mobile repair application available right now
Supports over 1,000+ Android models and devices
A world-class customer support team to help you whenever you need them

3,483,527 people have downloaded it

To help you have the best and the most accurate experience when using the Dr.Fone - System Repair (Android) application, here’s a complete step-by-step guide on how to use it.

Step One Make your way over to the Wondershare website and download the Dr.Fone - System Repair (Android) software. Install it onto your computer by following the on-screen instructions.

Once installed, connect your Itel P40 to your computer using a USB cable, and open the software, click “System Repair”.

Step Two Click the “Android” option in the menu and then click “Start” to begin the Repair process.

Step Three On the next screen, go through the options and use the drop-down menus to make sure the information is correct for your individual device. Accept the terms and conditions of the software, and then click the “Next” button.

Step Four Confirm you want the software to carry out the repair process by typing the ‘000000’ code into the pop-up box and pressing Confirm. Make sure you read everything displayed in this box beforehand to know what’s happening.

Step Five Now put your phone into Download Mode by following the on-screen instructions, so your device is ready for the repair process. The method for getting your phone into Download Mode will vary depending on your device, so make sure you’re following the right instructions.

Step Six Once the software has detected your device in Download Mode, it will automatically begin the repair process. You need to make sure your device stays connected throughout this time, and your computer stays on.

The whole process is automatic, so you won’t need to do anything until it’s finished. Once completed, you can disconnect your phone and start connecting it to the internet as normal!

safe & secure

Part 8. Check the Wi-Fi connectivity on another phone

When experiencing problems with your Wi-Fi network, it’s worth noting the problem might not be with your phone, but rather the Wi-Fi network itself. This is why it’s important to make sure you check the connection on another device.

Of course, if you’re already using another phone on your Wi-Fi network, you know this isn’t the case. However, if you’re not sure, here’s what you need to do;

Get another Android or iOS phone or tablet
Open the Settings menu and connect to the Wi-Fi network you’re having problems with
Enter the password and connect to the network
Open a web browser on the phone and try loading a web page
If the page loads, you know the Wi-Fi network isn’t the problem
If the page doesn’t load, you know you’ve got a problem with your Wi-Fi network

Part 9. Change the password of the Wi-Fi

Each Wi-Fi network router will give the opportunity to choose and change the password you have to let devices connect to your network. It’s important you try changing this because you never know if someone else has accessed your network and could be blocking your device. Here’s how it works;

Log onto your computer and open your Wi-Fi settings
Depending on the brand and method of your individual router, navigate to the Wi-Fi password settings menu
Change the password to something complicated using all available digits and characters
Save the password and restart the router to disconnect all devices
Now connect your Itel P40 to the router using the new password

Part 10. Reset network settings on Android

Just like the method above where you’ll be effectively resetting the network settings on your router, if this hasn’t worked, you’ll be able to reset the network settings on your Itel P40, hopefully removing the bugs and allowing you to connect.

Here’s how you can do this easily on your Itel P40;

From the home screen of your Itel P40, open the Settings menu
Tap the Backup & Reset option
Tap the Reset Network Settings option
Tap the Reset Network option
If you need to, enter the PIN number or passcode for the Android device, and the Itel P40 device will confirm the reset has taken place
Reconnect your Itel P40 to your Wi-Fi network for the changes to take effect

Part 11. Clear partition cache in recovery mode

As you continue to use your Itel P40, the partition cache will fill up with data your device needs and doesn’t need. However, by clearing your device’s partition cache, you can make clear up some space which should help your device have enough memory to connect to the internet.

Turn off your Itel P40
Turn it on by holding down the power button, volume button, and home button
When your phone vibrates, let go of the Power button, but continue to hold the volume button
When a menu is displayed, use the volume buttons to navigate the menu
Select the Android System Recovery option, followed by Wipe Cache Partition
Restart your device and connect to the internet

Part 12. Reset factory settings

If worse comes to worst, another option you have is to factory reset your Itel P40. As we’ve spoken about above, while using your phone from the day you started using it, your device will fill up with files and data which can become messy and causes bugs.

However, by factory resetting your device, you can start again from the factory default from which you first received it, ultimately clearing the bugs. Make sure you back up your device before proceeding because it will erase your personal files.

Open the Settings menu on your Itel P40
Navigate to System > Advanced > Reset Options
Tap the Reset phone option, and enter your PIN code if required
Tap Erase Everything
Wait for your phone to complete the process
Restart your device and connect to the internet

safe & secure

Ways to Unbrick Your Android Device: Various Ways for Recovery

When your Itel P40 becomes unresponsive or frozen after mistakenly flashing a ROM or rooting, you are informed that the phone has been bricked. The most terrifying aspect will not just be gadget loss, but also data erasure. However, what exactly is a bricked phone, and, more importantly, how do you fix a bricked Android phone?

This article will explain what a bricked android phone is, why an Android phone becomes bricked, how to unbrick an Android phone without losing data and a third-party application you can use.

Part 1. Causes of Bricked Phones

In everyday settings, our mobile devices have become our greatest friends, therefore breaking your phone is the last thing you want to do. There are different reasons why devices brick, and we must be familiar with them in order to comprehend the various techniques to repair bricked devices.

Here are some common reasons why your Itel P40 is bricked:

**Flashing Stock/Custom ROM:**It is possible that you installed an incompatible ROM in the Android phone, that the phone shuts off during the process, or that you have performed other errors that cause your phone to restart indefinitely or to become stuck at the starting screen.
**Rooting an Android device:**You are unable to effectively root the Itel P40 device.
**Android firmware is being updated:**If the phone is interrupted when updating the Android firmware, it will be bricked.
**Installing harmful applications:**You installed harmful programs on your Itel P40, or the phone was infected with a virus.

Part 2. How to Fix a Bricked Phone

The first step is to establish how badly your device is bricked. In most cases, you will be working with soft bricks that are pretty simple to repair. If your phone is stuck in a boot loop or enters recovery mode every time you turn it on, you may have a soft brick.

To repair bricked Android phones and tablets, you must first thoroughly examine the Itel P40 device’s state. Before you begin troubleshooting, determine the sort of bricking that your phone is experiencing. However, there is no specific software to unbrick your Itel P40; you may need to learn the complexities of this issue or hire a professional to do it for you.

Recover Now

safe & secure

Here are some simple methods for repairing bricked Android devices:

Method 1. Reboot the Phone in Safe Mode

Trying to reboot your android device in safe mode is the first and easiest thing you should try if your phone is bricked. Here’s how to do it:

Step 1: Turn off your smartphone and press the Volume Up + Power button to enter recovery mode. Then, using the volume controls, navigate the menu and select Reboot system now.

Step 2: Select the highlighted option by pressing the Power button. After that, wait for your device to reset normally.
Note: The steps for booting into recovery mode may change based on the manufacturer of your device. For further information, go to the user manual for your phone or tablet.

Method 2. Wipe the Cache Partition

This is the first indication that a user’s phone has gone bricked. The phone turned on automatically, however it became stuck or frozen on the logo screen. The issue might be caused by the undeleting of data and cache, which prevents the phone from displaying the home screen.

This issue, however, may be resolved by wiping the data and cache partitions in recovery mode. You must do the following to do this:

Step 1: Turn off your smartphone and enter recovery mode by pressing the Power and Volume Down buttons simultaneously. Different devices have various approaches for entering recovery mode, so you may perform better.
Step 2: After entering recovery mode, you should see the screen below. Remember to pick Advanced and then “Wipe Dalvik Cache” if your device is under Clockwork Mod recovery. Return to the main screen and select “Wipe Cache Partition” once more.

Step 3: Finally, on your smartphone, choose the Reboot system immediately.

Method 3. Perform a Factory Reset

A factory reset can undo the alterations made to your device that resulted in the brick phone, but you will lose everything you have downloaded and installed in the process. Here’s how to restore a bricked Android phone to factory settings:

Step 1: Boot your device into recovery mode (turn off your device, then press power button + volume up button).
Step 2: Select “Wipe Data/“Factory Reset” then confirm the action. When the process is done, you’ll be returned to the recovery mode menu.
Step 3: Select “Reboot System Now” to restart your device.

Method 4. Flash a Custom ROM

If you boot your phone directly into recovery mode, there’s a problem with the ROM you loaded. Then simply flash the following custom ROM on your phone:

Step 1: Save the required ROM (in ZIP format) to an SD card. The SD card should then be inserted into your Itel P40.
Step 2: Click the “Install zip from sdcard” button. Then, select the ZIP file that contains the ROM. Finally, click the “reboot system now” button.

Method 5. Using Wondershare Dr.Fone

Wondershare Dr.Fone - Data Recovery is the first data recovery solution for any damaged Android smartphone in the globe. It offers one of the greatest recovery rates and can recover a variety of information like images, videos, contacts, messages, and call logs. The program is most effective with Itel P40 smartphones.

While it is not an Android unbrick tool, it is a useful tool for retrieving data when your Itel P40 becomes bricked. It is quite easy to use:

Step 1: Launch Wondershare Dr.Fone and select “Data Recovery” > “Recover Android Data” from the menu. Then, select “****Recover from Broken Phone”.

Step 2: Choose the file types you wish to recover. Click “Next” and then select the type of damage your phone is experiencing. Select “Touch screen not responsive, or cannot access the phone” or “Black/broken screen”.

Step 3: Use the recovery wizard to enter your Android smartphone into Download Mode. Connect your Android handset to the computer after following the instructions to begin automatically analyzing your device.

Step 4: The program will provide a list of all recoverable files, organized by file type. To preview the file, highlight it. Choose the files you wish to recover and then click “Recover” to save all the data you want to restore.

safe & secure

Part 3. How to Prevent Bricking Your Phone

How to prevent a device from “bricking” itself and how to repair it if it does The delay is set by the MCU, but it should be long enough to allow the debug adapter to connect to the Itel P40 device and halt it before the Itel P40 device disables itself.

Here are some things to remember to prevent your device from bricking:

Avoiding unofficial firmware updates: Installing unapproved OS firmware on your phone will most certainly violate any manufacturer’s warranty you have on it. Read the installation instructions for your unique phone model thoroughly and then carefully follow them, taking time and patience.
**Being cautious when rooting or jail breaking:**Rooting and Jail breaking disables parts of the operating system’s built-in security mechanisms, which are part of what makes the operating system safe, and your data protected from exposure or damage.
**Install an antivirus application on your device:**Mobile devices increase the danger of data leaks and breaches. As a result, antiviral software is beneficial on mobile phones. Mobile Device Management is an excellent choice for virus protection on your mobile device.
Backup your phone data regularly: Backing up your phone safeguards your data in the event that you lose it, it is stolen, or it no longer works. When it comes time to replace your phone, having a backup makes it simple to restore your data to the new device. Furthermore, backing up your phone allows you to organize your data so that it is easier to access.
Avoid installing apps from untrusted sources: Apps installed from unauthorized sources make your device and personal data more exposed to dangers such as Ransomware. So you should be wary of where you download applications.

Conclusion

It is certainly upsetting when your gadget bricks, but you may attempt the solutions listed above to resolve the issue. Meanwhile, if you want to solve the problem quickly and easily, you can try Wondershare Dr.Fone. It can not only help you repair your Android smartphone, but it can also help you extract data from a bricked device, recover data, and many more Android device solutions!

safe & secure

How to Fix the Soft Bricked Itel P40?

Bricked phone is a serious problem, as your brick smartphone could be suffering from a soft brick or hard brick problem, and must be dealt with carefully. It is very common to see a brick smartphone these days. If you are wondering what exactly is a bricked phone, here is your answer.

A bricked phone, hard brick or soft brick, is a smartphone which refuses to start or boot all the way up the home/main screen of the Itel P40 device. This issue is observed within most Android phones because users have a tendency to tamper with the Itel P40 device settings, flashing new and customized ROMs and tweaking with the essential files. Playing around with the phone’s internal set-up leads to such errors, worst of them being a brick smartphone. Usually, a bricked phone does not switch on and stays frozen at the Itel P40 device logo, a blank screen or even worse, doesn’t respond to any command, even the power on command.

If you are confused about the soft brick and hard brick problems and looking for solutions to fix your priced phone, then here is all you need to know.

Read on to find out more.

Part 1: What is the difference between soft brick and hard brick?

To begin with, let us understand the basic difference between a soft brick and hard brick issue. Both versions of a bricked phone prevent it from booting but differ in their causes and gravity of the problem.

A soft-brick problem is caused merely by a software error/crash and makes your device switch on automatically every time you manually turn it off. This phenomenon is referred to as Boot Loop. Soft bricked Android phones are not as difficult to fix as the hard bricked Android phones. It is convenient to say that a soft bricked phone only boots up half-way and not fully, whereas a hard bricked device does not switch on at all. A hard brick error is thus caused when the kernel, which is nothing but an interface for the software to communicate with the hardware, is tampered with. A hard bricked phone is not recognized by your PC when plugged in and is a serious problem. It requires troubleshooting techniques and cannot be easily fixed as the soft brick problem.

hard bricked v/s soft bricked

Hard bricked phones are a rare sight, but the soft brick is very common. Given below are ways to fix a soft brick Android phone. The techniques listed here are the best and the most efficient ways to get your phone back to its normal working conditions without losing your important data or damaging your device or its software.

Part 2: Stuck at the Boot Loop

This is the first sign of a soft bricked Android phone. Boot Loop is nothing but when your phone does not remain switched off and turns itself on automatically, and freezes at the logo screen or blank screen, every time you manually try to power it off.

Stuck at boot loop problem can be fixed by clearing your Cache partitions. These partitions are nothing but storage locations for your modem, kernels, system files, drivers and built-in Apps data.

It is advisable to clear Cache partitions regularly to keep your phone free from such glitches.

Since the phone refuses to boot, Cache can be cleared from entering into the Recovery Mode. Different Android devices have different ways to put it in recovery mode. Normally pressing the power key and volume down key helps, but you may refer to your phone’s guide for better understanding and then follow the steps given below to clear the cache partition:

Once you are the recovery mode screen, you will see a number of options as shown in the screenshot.

Use the volume down key to scroll down and select ”Wipe cache partition” as shown below.

After the process is completed, select “Reboot System” which is the first option in the recovery mode screen.

This method will help you erase all the clogged up and unwanted files. You may loose some App related data, but that is a small price to pay to fix your bricked phone.

If this method does not boot up your brick smartphone and the problem still persists, there are two more things you can try. Read ahead to find out about them.

Part 3: Booting straight into recovery mode

If your bricked phone does not boot up to your Home Screen or Lock screen and instead boots directly into Recovery Mode, there is not much left to do. Booting straight into recovery mode is undoubtedly a soft brick error but it also indicates a possible problem with your current ROM. The only option you have to flash a new ROM to reboot your bricked phone back to its normal functioning.

To flash a new ROM:

Firstly, you must root your phone and unlock the Bootloader. Every phone’s mechanism to unlock the bootloader is different, thus, we suggest to refer to your user manual.

Once the Bootloader is unlocked, take a backup of all your data by selecting “Backup” or “Android” back in recovery mode. The process should not take long and all you need to do is tap “OK” to config backup.

In this step, download a ROM of your choice and store it in your SD Card. Insert the SD Card in your phone to begin the flashing process.

Once at the recovery mode, select “Install Zip from SD Card” from the options.

Scroll down using the volume key and use the power key to select the downloaded ROM.

This might take a few minutes of your time, but once the process is complete, reboot your phone.

Hopefully, your bricked phone will not boot normally and work smoothly.

Part 4: Booting straight into Bootloader

If your bricked phone boots straight into Bootloader, then this a serious issue and must not be taken lightly. Flashing a new ROM or clearing cache partitions are of little help in such a brick smartphone situation. Booting straight into Bootloader is a peculiar soft bricked Android phone feature and can be tackled only by downloading and flashing your original ROM from the manufacturer. In order to do so, a detailed study about your manufacturer’s ROM, ways to download and flash must be carried out. Since different Android phones come with different types of ROMs, it difficult to cover all the aspects about the different types of ROMs.

Brick smartphone problem has become more prominent than phone freezing or hanging issue. Android users are often seen looking for solutions to fix their soft brick and hard brick phones. Android phones are prone to get bricked and thus, it is important for us to know about the three techniques given above. These methods have been tried, tested and recommended by ay affected bricked phone users. Therefore, these tips are reliable and worth a try. So if your phone acts stubborn and refuses to boot normally, examine the problem carefully and adopt one of the solutions given above which best suits your situation.

Fix Guide

Itel P40 Not Connecting to Wi-Fi? 12 Quick Ways to Fix | Dr.fone