Reasons for Lava Yuva 2 Stuck on Startup Screen and Ways To Fix Them

There are many reasons why phones get stuck on the boot screen. It could be something as simple as physical damage or more complicated related to software problems. Having your phone stuck on the logo screen, or boot screen is annoying, and it is no surprise that people will find ways to fix this issue when encountered.

This article will share the possible reasons why your phone is stuck on the boot screen. This article will share three possible reasons for this problem and three valuable tips to help fix this issue. If all else fails, there is an application that is recommended and is sure to solve your issue in no time. Keep on reading to find out more!

It is not uncommon for phones to be stuck on the startup screen, but finding out why this happens is tricky. This section identified some of the top reasons your cellphone could have gotten stuck on the startup screen.

Physical Damage to the Phone

If you accidentally dropped your phone or knocked it on a hard surface, you could have damaged the internal hardware of your phone. This could affect your phone’s ability to reboot and result in your phone being stuck on the boot screen.

If you are 100% certain that your phone has gone through physical damage, you should seek professional help to have your phone repaired or checked. It is advised not to fix this problem yourself as your phone’s internal parts are complicated and delicate. Look for an official phone repair store and get your phone fixed for issues like your phone getting stuck on the logo.

Liquid Damage

It is not common for your phone to expose to water. Rain or water splashes are unavoidable; sometimes, your phone gets wet. Little exposure to water on the surfaces of your phone is fine. However, if you fall into a pool with your phone or drop it in a puddle of water, your phone will likely suffer from liquid damage.

Even the tiniest water droplet that seeped into your phone could damage the internal hardware of your device, often leaving you with your phone stuck on the boot screen. The first thing to do when you accidentally submerge your phone in the water is to check if the water has damaged your phone.

For iPhone users, look for the water damage indicator. If you see that it has turned from white to red, it has suffered from water damage. You have two options if your phone has suffered liquid damage. One is dismantling your phone and letting it dry for at least 48 hours. Two is bringing your phone to a repair shop to fix it.

Software Issues

Software issues are probably the most common reason your phone is stuck on the logo screen. Eight times out of ten, software issues are either caused by a failed software update, using an older version of the operating system, or having a jailbroken phone. When the software does not successfully update, the phone will have no operating system, as the old system was erased before the new software was installed.

The older operating system is also not desired as your phone typically will send periodic updates to make sure your phone is up-to-date and free from bugs. Running applications on an older operating system might lead to issues like the phone being stuck on the boot screen or the logo. Hence, updating your phone to the latest software version would be better.

Part 2. 3 Helpful Ways To Fix Phones Stuck on Boot Screen

After understanding the common problems on why your phone is stuck on the startup screen page, here are three easy solutions to try solving yourself at home.

Hard reboot your phone

To quickly fix any of your phone issues, especially when stuck on the startup screen, perform a hard reboot. The term hard reboot means turning your device off and on again. You might think this is a simple option, but this is a tried and tested method that might work on a minor glitch that results in your smartphone getting stuck on the startup screen page.

Here is an example of performing a hard reboot for an Android phone such as Lava Yuva 2. Preess and hold the Power and Volume Down buttons simultaneously for more than 7 seconds to perform the hard reboot.

Put your phone in recovery mode

If a hard reboot does not work, a natural next step is to try going into recovery mode. The recovery mode is specially designed to solve any software-related issues. It is important to note that entering recovery mode will delete all your corrupted files and replace them with a functional operating system. Hence, back up all your files to ensure you retain all your information.

Here is a step-by-step process for putting your Lava Yuva 2 or Redmi smartphone in recovery mode.

Step 1: Tap and press the Power button to switch off your Lava Yuva 2/Redmi phone

Step 2:Hold the Volume Up and the Power buttons at the same time, then release the keys when the Main menu of Recovery mode appears on the screen.

Step 3: You can use the volumes buttons to navigate up and down and press the Power key to confirm the selection.

Factory Reset

If you do not want to attempt recovery mode, you can try resolving the issue of your phone being stuck on the startup screen through Factory Reset. Factory Reset, also called Hard Reset, erases all information and data on your device. As a result, it will return to the settings and recover the data it used to have when leaving the factory.

Here is an example of putting your Samsang smartphone into the Factory Reset DFU mode.

Step 1: Open the Settings application on your phone and tap General Management.

Step 2: Go to Reset > Factory data reset.

Step 3: Swipe to and tap Reset.

Note: Before carrying out a factory reset, you need to input the password of your Lava Yuva 2 Account.

Bonus Tip: Best App To Solve Phone Stuck on Boot Screen

If all the solutions above do not work and you do not want to perform a factory reset on your phone, one option is to use an application called Wondershare Dr.Fone. It is one of the most effective phone recovery solutions and can help to bring your phone back to a state like it was brand new. Being stuck on the startup screen page will be a problem of the past.

The following steps will show you how to use Dr.Fone to perform system repair on your phone.

Step 1: To the Dr.Fone application using the link above and click on System Repair.

Step 2: Depending on the Lava Yuva 2 device you are using, choose either Android or iPhone.

Step 3: In the next window, select the issue you are facing and click Start.

Step 4: Choose the corresponding Brand, Name, Model, Country, and Carrier from each drop-down menu and click Next.

Tip: Make sure the information you input is accurate, as it will affect the system repair if the information is inaccurate.

Step 5: Connect your device to your computer and follow the instructions on the screen to enter Download mode. Click on Next to proceed to the next step.

Step 6: Wait for the process to complete, and a new firmware will be updated on your device. Power on your phone and check if the issue still exists.

Frequently Asked Questions

The following are interesting and frequently asked questions about how to solve boot loops.

1. What is a boot loop?

A boot loop describes a process when Your Lava Yuva 2 stays stuck in a circle of rebooting. When your phone is stuck on the startup screen, one of the strategies you will try is to restart your device. However, when your phone gets stuck in a boot loop, it is your device’s way of trying to turn it off and on again to fix the issue.

Since there is an issue with the booting process, it will keep running into the same error repeatedly, calling the boot loop. When trapped in a boot loop, your device will keep turning off and on. Most boot loop issues are software-related, such as a wrong system update.

2. How do you fix a boot loop?

When stuck in a boot loop, there are different troubleshooting methods for other devices. For Android phones, force your phone into its Recovery mode; from there, you can restore a previous backup. This backup could be from when the boot loop did not exist, so recovery to that backup could quickly solve the problem.

For iPhones, it is the same concept as the Android, restore your phone to the previous backup. You can use iTunes to restore a previously stored backup on your computer.

3. How to prevent a boot loop?

A boot loop typically starts when there is a change to your system before a reboot cycle. Most issues are software-related, such as having to do a system upgrade gone wrong or a problem that doesn’t mesh. One way to prevent this is to perform a software or system upgrade constantly. Make your phone juiced to prevent it from turning off mid-way when updating.

safe & secure

3,405,439 people have downloaded it

Conclusion

This article summarizes some of the possible reasons why your phone is stuck on the boot screen. It demonstrated three useful strategies to overcome your phone stuck in the boot with ease. However, if all the above methods do not work, why not try Dr.Fone-System Repair?

Dr.Fone-System Repair repairs the operating system issues and fixes the issue with your phone. Once you power on your phone again, you can rest assured that it will be like new.

Lava Yuva 2 Bootloop Problem, How to Fix it Without Data Loss

Have you, like many other users, faced the bootloop Android problem and wondered what exactly is Android boot loop. Well, Android boot loop is nothing but an error that makes your phone switch on itself every time you manually turn it off. To be precise, when your Lava Yuva 2 does not remain switched off or powered off and starts to boot up automatically after a few seconds, it might be stuck in the boot loop Android.

An Android boot loop is a very common problem and is one of the first symptoms of a soft-bricked device. Also, when your device is experiencing Android boot loop issue, it does not start normally to reach the Home or Locked Screen and remains frozen at the Lava Yuva 2 device’s logo, Recovery Mode or a lit-up screen. Many people fear losing their data and other files due to this error and thus, it is a very confusing situation to be in.

We understand the inconvenience caused, therefore, here are ways to tell you how to fix the bootloop problem in Android devices without losing any important data.

However, before moving on, let us learn a little about the causes for the Android boot loop error.

Part 1: What might cause the bootloop issue on Android?

Android boot loop error might seem weird and unexplainable but it occurs because of some specific reasons.

Firstly, please understand that it is a misnomer that boot loop error occurs only in a rooted device. Boot loop Android error can also occur in a stock device with the original software, ROM, and firmware.

In a rooted device, changes made, such as flashing a new ROM or customized firmware which are not compatible with the Lava Yuva 2 device’s hardware or existing software, can be blamed for the boot loop problem.

Moving on, when your device’s software is unable to communicate with the system files during the start-up process, Android boot loop problem may arise. Such a glitch is caused if you have recently updated the Android version.

Also, corrupt App update files may also cause the bootloop Android issue. Apps and programs downloaded from unknown sources bring in a particular type of virus that prevents you from using your device smoothly.

All-in-all, Android boot loop error is a direct outcome of when you try to tamper with your device’s internal settings.

Hence, if you are looking for ways to guide you about how to fix boot loop issue, you will have to revamp the Lava Yuva 2 device internally by either resetting it or adopting a recovery method.

Read on to know more about how to fix the bootloop error without any data loss when your device suffers from the bootloop Android problem.

Part 2: One click to Fix Android Bootloop without factory reset

If you are trying to figure out how to fix boot loop, the first option you have is the one-click fix to Android Bootloop which involves using the Dr.Fone - System Repair software.

This is designed to repair any data corruption on your device and restores your firmware to its usual working condition.

Dr.Fone - System Repair (Android)

One click to fix boot loop of Android

• #1 Android repair solution from your PC, can fix a wide range of Android system issues, such as boot loop, black screen, etc.
• The software requires no technical expertise, and anybody can use it
• A one-click solution when learning how to fix Android boot loop
• Not require root Android phones.
• Works with most Lava Yuva 2 devices, including the latest Lava Yuva 2 phones like S22
• Simple and easy-to-use user interface

4,689,059 people have downloaded it

To help you get started, here’s a step-by-step guide on how to use Dr.Fone - System Repair.

Note: This method can erase data on your device, including your personal files, so make sure you’ve backed up your device before proceeding.

Step #1 Download the Dr.Fone - System Repair software from the website and install it onto your computer.

Open the software and select the System Repair option from the main menu to fix the Android bootloop error.

Step #2 Connect your Lava Yuva 2 to your computer using the official cable and select the “Android” option from the three menu items. Click “Start” to confirm.

You’ll then need to input the Lava Yuva 2 device information, such as your carrier info, device name, model, and country/region in order to ensure you’re downloading and repairing the correct firmware to your phone.

Step #3 Now you’ll need to put your phone into Download Mode to remove the Android bootloop.

For this, you can simply follow the onscreen instructions for both phones with and without home buttons.

Click “Next”, and the software will begin downloading the firmware repair files.

Step #4 Now you can sit back and watch the magic happen!

Make sure your computer stays connected to the internet, and your device stays connected to your computer throughout the entire process. Once the firmware has been downloaded, it will be automatically installed onto your mobile device, removing the boot loop Android error.

You’ll be notified when the process is done and when you can remove your device and start using free from the boot loop Android error!

safe & secure

Part 3: Soft reset to fix Android bootloop issue

When your device is stuck in Android boot loop, it does not necessarily mean that it is bricked. Boot loop might be occurring due to a simpler problem which can be fixed by turning off your device. This sounds like a home remedy for a serious problem but it works and resolves the problem most of the time.

Follow the steps given below to soft reset your device:

Turn the Lava Yuva 2 device off and take out its battery.

If you cannot take the battery out, let the phone be off for about 3 to 5 minutes, and then turn it back on.

Simply performing a soft reset on your device can help you if you are looking for solutions for how to fix the bootloop issue. This a very useful method as it does not result in any kind of loss in data and protects all your media files, documents, settings, etc.

In case the Lava Yuva 2 device does not turn on normally and is still stuck in the bootloop Android problem, be prepared to use the troubleshooting techniques given and explained below.

Part 4: Boot into Safe Mode to fix Android boot loop

Booting your Lava Yuva 2 into Safe Mode is a useful troubleshooting step to fix boot loop issues caused by third-party apps. When in Safe Mode, the Lava Yuva 2 device will start up with only essential system apps, and any downloaded apps that might be causing conflicts won’t run. Here’s how you can boot your Lava Yuva 2 into Safe Mode to address the boot loop problem:

Step 1: Power Off Your Device

Hold down the power button until it turns off completely.

Step 2: Access Safe Mode

To enter Safe Mode, follow these steps based on your device model:

• For most Android devices: Press and hold the power button to turn on your device. As soon as the manufacturer’s logo appears, press and hold the Volume Down button until the Lava Yuva 2 device finishes booting. You should see “Safe Mode” displayed in the bottom left or right corner of the screen.
• Some devices might require slightly different key combinations. Refer to your device’s user manual or perform an online search for the specific method to enter Safe Mode for your model.

Step 3: Observe the Lava Yuva 2 device

Once your device has booted into Safe Mode, use it for a while to see if the boot loop issue persists. If the boot loop doesn’t occur in Safe Mode, it indicates that the problem is likely caused by a third-party app.

Step 4: Identify and Uninstall Problematic Apps

Now that you’re in Safe Mode, it’s time to identify the troublesome app. Start by uninstalling recently installed apps one by one until the boot loop problem is resolved. After each uninstallation, restart your device normally to check if the boot loop still occurs. Continue this process until you find the problematic app.

Step 5: Restart Normally

Once you’ve identified and uninstalled the problematic app, restart your device normally to exit Safe Mode. Your Android device should now start up without getting stuck in a boot loop.

By following these steps and using Safe Mode to isolate problematic apps, you can effectively troubleshoot and resolve boot loop issues on your Lava Yuva 2.

Part 4: Factory reset to fix Android bootloop issue

Factory reset, also known as Hard Reset, is a one-stop solution for all your software resulting in issues. Android boot loop being such problem, can be easily overcome by performing a factory reset.

Please note that all your device’s data and settings will be deleted by adopting this method. However, if you have a Google account signed in on your Lava Yuva 2, you will be able to retrieve most of your data once the Lava Yuva 2 device turns on.

To factory reset your Android boot loop device, you must first boot into the Recovery Mode screen.

To do this:

Press the volume down button and power button together until you see a screen with multiple options before you.

When you are at the Recovery Mode screen, scroll down using the volume down key, and from the options given, select “Factory Reset” using the power key.

Wait for your device to perform the task and then:

Reboot the phone in Recovery Mode by selecting the first option.

This solution is known to fix the boot loop error 9 out of 10 times, but if you still can’t start your Lava Yuva 2 normally, consider using a CWM Recovery to resolve the Android boot loop issue.

Part 5: Use CWM Recovery to fix bootloop on rooted Android

CWM stands for ClockworkMod and it is a very popular custom recovery system. To use this system to solve the boot loop Android error, your Lava Yuva 2 must be rooted with CWM Recovery System which basically means CWM must be downloaded and installed on your device.

Furthermore, to use CWM Recovery to fix boot loop on rooted Android devices, follow the steps given below:

Press the home, power, and volume up buttons to launch the CWM Recovery screen.

Note: you might have to use a different combination of keys to enter into Recovery Mode, depending on your device’s model.

Click here

Scroll down using” the volume key to select “Advanced”.

Now select “Wipe” and choose to wipe “Dalvik Cache”.

In this step, select “Mounts and Storage” to click on “Wipe” or “Cache”.

Once this is done, make sure to reboot your Lava Yuva 2.

This process with successfully fix the Android boot loop error and not cause any loss of data stored on your device stuck in boot loop.

So the bottom line is that boot loop Android issue may seem like an irreparable error but it can be resolved by carefully following the techniques explained above. These methods not only tell you how to fix the bootloop problem but also prevent it from occurring in the future.

An Android boot loop is a common phenomenon with all Android devices because we tend to tamper with our device’s internal settings. Once the ROM, firmware, kernel, etc are damaged or rendered incompatible with the Lava Yuva 2 device’s software, you cannot expect it to function smoothly, hence, the boot loop error occurs. Since you are not the only one suffering from the Android boot loop problem, be rest assured that the ways, given above, to combat it are recommended by users facing similar troubles. So, don’t hesitate and go ahead to try them on.

safe & secure

Why Is My Lava Yuva 2 Offline? Troubleshooting Guide

Ever had your Lava Yuva 2 claim it’s offline, leaving you scratching your head about where it went wrong? We get it; it’s confusing. That’s why this article is here to untangle the mystery.

In the following sections, we’re diving into the “why is My Lava Yuva 2 offline” dilemma that many Android users face. We’ll break down the possible reasons behind this common issue and guide you through simple steps on how to fix it. By the end of the article, you’ll be able to get back to smooth internet surfing on your Lava Yuva 2. Let’s get started.

Part 1: Why Does My Lava Yuva 2 Say Offline?

When you encounter the “offline” error message, it can disrupt your usual smartphone activities. Suddenly, you find yourself unable to browse the internet, send or receive emails, or stay connected through instant messages.

It’s a frustrating scenario, but let’s break down the potential reasons why your phone might be displaying this offline status:

1. Enabling Airplane mode

Why is My Lava Yuva 2 showing offline? Well, one common culprit behind the “offline” message is the accidental activation of Airplane Mode on your Lava Yuva 2. When Airplane Mode is enabled, it disconnects your phone from all wireless networks, rendering it unable to connect to the internet or cellular networks.

2. Internet connection issues

Fluctuations in your signal strength or unexpected data loss can also be the culprit behind the “Why is My Lava Yuva 2 offline?” problem. Android devices rely on stable internet connections, and disruptions, whether temporary or prolonged, can lead to this error.

3. Glitches or bugs

Sometimes, glitches or bugs in Google apps installed on your Lava Yuva 2 can mislead it into thinking it’s offline. Google Play Services or other related applications may encounter issues, causing the phone to display an “offline” message.

4. Firewall restrictions

In some cases, a firewall on your Lava Yuva 2 might be overly restrictive, preventing the Lava Yuva 2 device from establishing a connection to the internet. This security measure, intended to protect your device, can sometimes go overboard and disrupt normal online functionality.

Now, you have understood the potential causes as the first step toward resolving the issue. Next, we’ll guide you through the process of troubleshooting and getting your Lava Yuva 2 back online.

Part 2: How To Fix “Phone Offline” With Internet Connection Problem

Now that we’ve figured out why your phone says it’s offline, let’s tackle the issue head-on. If you’re facing problems like downloads that won’t start, Google Play stuck on “Loading…,” or web pages refusing to load, chances are it’s an internet connection issue causing the problem.

Here are some easy solutions to get your connection back.

Solution 1: Change connection to mobile data

Switching to mobile data can be a quick fix if your Wi-Fi is acting up. It ensures a change in your connection source and might resolve the “Phone offline” issue. Follow these easy steps to change your connection to mobile data:

• Step 1: Swipe down from the top of your screen to access the Quick Settings menu.
• Step 2: Tap the Wi-Fi icon to turn off the Wi-Fi connection.
• Step 3: Tap Mobile Data to turn it on.

Solution 2: On and off Airplane mode

Airplane Mode can sometimes cause connectivity confusion. Turning it off and on essentially resets your phone’s wireless connections, which might resolve the offline issue.

How to on and off Airplane mode on Android:

• Step 1: Swipe down from the top of your screen to access the Quick Settings menu.
• Step 2: Look for the Airplane Mode icon and tap the icon to turn on Airplane Mode.
• Step 3: Wait a few seconds, then tap it again to turn off the Airplane Mode. Now, check if your phone is now online.

Solution 3: Reset network settings

Resetting network settings can help eliminate any configuration glitches that might be causing the phone offline problem. It’s like giving your phone’s connection settings a fresh start.

To reset your network settings, the steps may differ depending on the phone model you are using. However, you can generally do so by looking for the “Network” settings.

• Step 1: Open your phone’s Settings > Connection & sharing.
• Step 2: Find and select “Reset Wi-Fi, mobile networks, and Bluetooth.”
• Step 3: Tap “Reset Settings” and confirm the action and allow your phone to reset.
• Step 4: Reconnect to your Wi-Fi and check if the issue persists.

Solution 4: Restart your Wi-Fi router

Sometimes, the problem might not be with your phone but rather with the Wi-Fi router. Restarting it can refresh the connection and potentially resolve the connectivity problem.

How to restart your Wi-Fi router:

• Step 1: Locate your Wi-Fi router.
• Step 2: Turn off the router using the power button or unplug it.
• Step 3: Wait for about 10–15 seconds before plugging the router back in or turning it on.
• Step 4: Allow the router to restart and establish a connection. Then, check if your phone still shows the “Phone Offline” message.

These solutions should cover the most common connectivity issues. If the problem persists, we’ll explore further steps in the following sections.

Part 3: How To Fix “Phone Offline” Despite Having an Internet Connection

Ever found it odd to receive the frustrating offline error message when you’re sure your internet connection is up and running? If you’ve double-checked your internet connection and your phone still says it’s offline, the issue may lie within your browser, apps, or device settings.

In this part, we’ll answer the question “**Why does My Lava Yuva 2 say offline android?**” despite a seemingly functional internet connection. Then, let’s see other solutions on how to get your device back to its online, fully functional self.

Solution 1: Clear Google Chrome’s cache and data

Sometimes, the answer to “Why is my Android phone offline” can be attributed to a buildup of corrupted or outdated data in your browser’s cache. Clearing the cache and data for Google Chrome can resolve this issue, allowing for a fresh start and potentially eliminating the offline status.

How to clear your browser’s cache and data on Android:

• Step 1: Open the Settings > Apps > Manage Apps.
• Step 2: Locate and tap “Google Chrome” or your preferred browser in the list of installed apps.
• Step 3: Tap “Storage” and select “Clear Cache” to remove temporary files.
• Step 4: Choose “Clear Data” to delete app data. Confirm the action if prompted.

Now, restart Google Chrome and check if the offline error persists.

Solution 2: Re-install Google Chrome

If clearing the cache and data didn’t solve the offline issue, reinstalling Google Chrome can be the next step. A fresh installation can eliminate any underlying glitches or corrupted files that might be causing the persistent offline status.

How to re-install Google Chrome:

• Step 1: Visit the Google Play Store and search for Google Chrome.
• Step 2: Tap “Uninstall” to remove the app from your device.
• Step 3: Wait until it has finished uninstalling your app. Then, tap “Install” to start reinstalling the app.
• Step 4: Once the installation is complete, open Google Chrome and check if the offline error persists while browsing.

Solution 3: Repair the system to fix the phone showing offline

When persistent offline issues seem deeply rooted in your device’s system, a comprehensive system repair may be the solution. Wondershare Dr. Fone’s system repair tool is designed to address a range of system problems, providing a reliable way to fix any problem you have with your phone.

With Dr. Fone’s system repair tool, you can diagnose and resolve “Why is My Lava Yuva 2 offline on Android,” ensuring a smooth and functional Android experience.

Key Features:

• Comprehensive system repair for any devices
• User-friendly interface
• Efficient problem diagnosis

How to use Dr. Fone’s system repair tool:

• Step 1: Open Dr.Fone’s system repair tool

Start by launching Wondershare Dr.Fone on your computer. Go to the Toolbox section and connect your Lava Yuva 2. Choose System Repair and pick Android as your device type.

safe & secure

3,189,324 people have downloaded it

• Step 2: Start the repair

Click Start on the new screen to kick off the repair. Since you’re dealing with an offline connection issue on Android, select System Damage.

• Step 3: Confirm your device details

The platform will detect your Lava Yuva 2’s brand. Confirm the Name, Model, Country, and Carrier. If your device is unlocked, choose OPEN in the Carrier section. Agree to the warning, click Next, and proceed with the repair.

• Step 4: Download firmware.

Follow the instructions to put your Lava Yuva 2 into Download Mode. Once in Download Mode, you will start downloading the firmware.

• Step 5: Confirm Installation

Remember, the repair may erase data. It’s advisable to back up your data first before starting the repair. Enter “000000” to confirm the repair process, shown by a progress bar. Click Done once it is completed and see if your Android is back online.

Conclusion

Dealing with the “Phone Offline” hiccup on your Lava Yuva 2 can be a real headache. But fear not – we’ve covered a range of solutions to get you back online smoothly. From troubleshooting internet connection problems to addressing browser and app-related glitches, the solutions provided in this guide are designed to cater to a variety of scenarios. If you find it troublesome to try solutions one by one, then we recommend using Dr.Fone directly which is a full toolkit for your phone and can help resolve most device glitches one-off.

Remember, technology can sometimes be tricky. But with patience and the right guidance, you can overcome these challenges.

Also read: