Reasons for Tecno Spark 10C Stuck on Startup Screen and Ways To Fix Them

There are many reasons why phones get stuck on the boot screen. It could be something as simple as physical damage or more complicated related to software problems. Having your phone stuck on the logo screen, or boot screen is annoying, and it is no surprise that people will find ways to fix this issue when encountered.

This article will share the possible reasons why your phone is stuck on the boot screen. This article will share three possible reasons for this problem and three valuable tips to help fix this issue. If all else fails, there is an application that is recommended and is sure to solve your issue in no time. Keep on reading to find out more!

It is not uncommon for phones to be stuck on the startup screen, but finding out why this happens is tricky. This section identified some of the top reasons your cellphone could have gotten stuck on the startup screen.

Physical Damage to the Phone

If you accidentally dropped your phone or knocked it on a hard surface, you could have damaged the internal hardware of your phone. This could affect your phone’s ability to reboot and result in your phone being stuck on the boot screen.

If you are 100% certain that your phone has gone through physical damage, you should seek professional help to have your phone repaired or checked. It is advised not to fix this problem yourself as your phone’s internal parts are complicated and delicate. Look for an official phone repair store and get your phone fixed for issues like your phone getting stuck on the logo.

Liquid Damage

It is not common for your phone to expose to water. Rain or water splashes are unavoidable; sometimes, your phone gets wet. Little exposure to water on the surfaces of your phone is fine. However, if you fall into a pool with your phone or drop it in a puddle of water, your phone will likely suffer from liquid damage.

Even the tiniest water droplet that seeped into your phone could damage the internal hardware of your device, often leaving you with your phone stuck on the boot screen. The first thing to do when you accidentally submerge your phone in the water is to check if the water has damaged your phone.

For iPhone users, look for the water damage indicator. If you see that it has turned from white to red, it has suffered from water damage. You have two options if your phone has suffered liquid damage. One is dismantling your phone and letting it dry for at least 48 hours. Two is bringing your phone to a repair shop to fix it.

Software Issues

Software issues are probably the most common reason your phone is stuck on the logo screen. Eight times out of ten, software issues are either caused by a failed software update, using an older version of the operating system, or having a jailbroken phone. When the software does not successfully update, the phone will have no operating system, as the old system was erased before the new software was installed.

The older operating system is also not desired as your phone typically will send periodic updates to make sure your phone is up-to-date and free from bugs. Running applications on an older operating system might lead to issues like the phone being stuck on the boot screen or the logo. Hence, updating your phone to the latest software version would be better.

Part 2. 3 Helpful Ways To Fix Phones Stuck on Boot Screen

After understanding the common problems on why your phone is stuck on the startup screen page, here are three easy solutions to try solving yourself at home.

Hard reboot your phone

To quickly fix any of your phone issues, especially when stuck on the startup screen, perform a hard reboot. The term hard reboot means turning your device off and on again. You might think this is a simple option, but this is a tried and tested method that might work on a minor glitch that results in your smartphone getting stuck on the startup screen page.

Here is an example of performing a hard reboot for an Android phone such as Tecno Spark 10C. Preess and hold the Power and Volume Down buttons simultaneously for more than 7 seconds to perform the hard reboot.

Put your phone in recovery mode

If a hard reboot does not work, a natural next step is to try going into recovery mode. The recovery mode is specially designed to solve any software-related issues. It is important to note that entering recovery mode will delete all your corrupted files and replace them with a functional operating system. Hence, back up all your files to ensure you retain all your information.

Here is a step-by-step process for putting your Tecno Spark 10C or Redmi smartphone in recovery mode.

Step 1: Tap and press the Power button to switch off your Tecno Spark 10C/Redmi phone

Step 2:Hold the Volume Up and the Power buttons at the same time, then release the keys when the Main menu of Recovery mode appears on the screen.

Step 3: You can use the volumes buttons to navigate up and down and press the Power key to confirm the selection.

Factory Reset

If you do not want to attempt recovery mode, you can try resolving the issue of your phone being stuck on the startup screen through Factory Reset. Factory Reset, also called Hard Reset, erases all information and data on your device. As a result, it will return to the settings and recover the data it used to have when leaving the factory.

Here is an example of putting your Samsang smartphone into the Factory Reset DFU mode.

Step 1: Open the Settings application on your phone and tap General Management.

Step 2: Go to Reset > Factory data reset.

Step 3: Swipe to and tap Reset.

Note: Before carrying out a factory reset, you need to input the password of your Tecno Spark 10C Account.

Bonus Tip: Best App To Solve Phone Stuck on Boot Screen

If all the solutions above do not work and you do not want to perform a factory reset on your phone, one option is to use an application called Wondershare Dr.Fone. It is one of the most effective phone recovery solutions and can help to bring your phone back to a state like it was brand new. Being stuck on the startup screen page will be a problem of the past.

The following steps will show you how to use Dr.Fone to perform system repair on your phone.

Step 1: To the Dr.Fone application using the link above and click on System Repair.

Step 2: Depending on the Tecno Spark 10C device you are using, choose either Android or iPhone.

Step 3: In the next window, select the issue you are facing and click Start.

Step 4: Choose the corresponding Brand, Name, Model, Country, and Carrier from each drop-down menu and click Next.

Tip: Make sure the information you input is accurate, as it will affect the system repair if the information is inaccurate.

Step 5: Connect your device to your computer and follow the instructions on the screen to enter Download mode. Click on Next to proceed to the next step.

Step 6: Wait for the process to complete, and a new firmware will be updated on your device. Power on your phone and check if the issue still exists.

Frequently Asked Questions

The following are interesting and frequently asked questions about how to solve boot loops.

1. What is a boot loop?

A boot loop describes a process when Your Tecno Spark 10C stays stuck in a circle of rebooting. When your phone is stuck on the startup screen, one of the strategies you will try is to restart your device. However, when your phone gets stuck in a boot loop, it is your device’s way of trying to turn it off and on again to fix the issue.

Since there is an issue with the booting process, it will keep running into the same error repeatedly, calling the boot loop. When trapped in a boot loop, your device will keep turning off and on. Most boot loop issues are software-related, such as a wrong system update.

2. How do you fix a boot loop?

When stuck in a boot loop, there are different troubleshooting methods for other devices. For Android phones, force your phone into its Recovery mode; from there, you can restore a previous backup. This backup could be from when the boot loop did not exist, so recovery to that backup could quickly solve the problem.

For iPhones, it is the same concept as the Android, restore your phone to the previous backup. You can use iTunes to restore a previously stored backup on your computer.

3. How to prevent a boot loop?

A boot loop typically starts when there is a change to your system before a reboot cycle. Most issues are software-related, such as having to do a system upgrade gone wrong or a problem that doesn’t mesh. One way to prevent this is to perform a software or system upgrade constantly. Make your phone juiced to prevent it from turning off mid-way when updating.

safe & secure

3,405,439 people have downloaded it

Conclusion

This article summarizes some of the possible reasons why your phone is stuck on the boot screen. It demonstrated three useful strategies to overcome your phone stuck in the boot with ease. However, if all the above methods do not work, why not try Dr.Fone-System Repair?

Dr.Fone-System Repair repairs the operating system issues and fixes the issue with your phone. Once you power on your phone again, you can rest assured that it will be like new.

How To Deal With the Tecno Spark 10C Screen Black But Still Works?

With the advance of technology over the years, many of us rely on smartphones to communicate, work, and play. As such, it can be pretty concerning when your device begins to act strange like your phone screen suddenly went blank.

Whether you’re using an iPhone or an Android device, you’ll eventually encounter a problematic symptom like this. Therefore, this article will explore what to do when your phone screen goes black. After exploring below, you’ll learn the common causes of why your phone screen went black and how to fix it. Read on below to learn more.

Part 1: Why Did My Tecno Spark 10C Screen Go Black but Still Works? Common Causes

Experiencing a cell phone blank screen is not exclusive to Android or iOS users. A phone screen not turning on happens all the time due to several factors that may or may not be out of your control. While they can be frustrating, here are some common causes you should know as to why your phone screen went black but still works.

A Drained Battery

The first thing that comes to mind when your phone screen suddenly goes black is you have a drained battery. Even though this is obvious, it’s still important to mention, as this is usually what most people encounter. To fix this problem, plug your smartphone into a charger and wait for your device to turn on again. If it works, then you just prevented a rather annoying experience.

App Troubles

If your phone is working, but the screen is black, there’s also a high probability that you are having an isolated issue with a particular application. An app could be loading something, which often happens for streaming apps such as YouTube, Netflix, Prime, and more, especially if you have slow internet connectivity.

Software Issues

A potential reason why your phone screen went black but still works could be because of your smartphone’s software. This problem suggests that your Tecno Spark 10C is crashing, potentially freezing your device if not addressed immediately. If this is the cause, then your device is likely experiencing a critical system error, and you should directly try to reboot your phone.

Hardware Problem

If you dropped your phone, there’s a high chance the LCD connectors went loose due to the physical impact. If this happened to you, the phone might be working, but the screen is black due to the LCD cable dislodging. Another issue could be your phone got exposed to extreme temperatures. This can also cause a black screen but your phone is still on.

Part 2: How To Fix Black Screen on Your Phone

Here are four valuable methods you should know on what to do when your phone screen goes black on your iPhone or Android smartphone to get them working again.

Method 1: Force Restart your Android/iOS Smartphone

If your phone screen is black but still works, force restarting it is the easiest way to fix it. The following are the detailed steps for both Android and iOS devices.

How to Force Restart your Android Device

Here is how you force restart an Android device when your phone screen doesn’t turn on.

Step 1: Press and hold the Power and Volume Down buttons simultaneously.

Step 2: Hold the same buttons until your device restarts, and display the phone’s logo.

How to Force Restart your iOS Device

If you own the latest iPhone models, here are the method of restarting it from iPhone 8 up to 14.

Step 1: Press and immediately release Volume Up. Next, press and immediately release Volume Down.

Step 2: Press and hold Sleep/Wake until you see the Apple logo.

Note

If you own an iPhone 7, press and hold the Side button and Volume Down simultaneously until you see the apple logo.

Method 2: Uninstall or Update Outdated Applications

In some cases, your phone screen is black but still works because of installing incompatible apps on your iOS/Android device. If the installed app is frequently crashing, it may be the source of a blank cell phone screen. Uninstall the problem app to see if the black screen disappears or not.

Method 3: Inspect the LCD Connectors

If your phone screen goes black but still works, you should inspect the logic board to the LCD screen to see if it has become disconnected. It is common for smartphones that often get dropped a few times. It’s best to plug the connectors back to regain your screen’s functionality.

However, this requires technical know-how. It’s better to seek help from a professional as you could risk causing more damage to your device if you don’t know what you’re doing.

Method 4: Perform a Factory Reset

If all the methods above did not solve your problem, the last resort you can take is to perform a Factory Reset. This method works on Android and iOS smartphones and erases all your data. It is the quickest way to try to fix why your phone screen went black. Here are the steps.

For Android Users

If you’re on Android, tap Settings > Backup and Reset. Tap on Factory data reset > Delete all to initiate the factory reset.

If you cannot do this, here’s how to perform a factory reset manually using Recovery Mode.

Note

The process of booting into Recovery Mode is not the same across all Android devices and depends on the manufacturer and model of your phone. Refer to your owners manual to see which method is the right one for your Tecno Spark 10C.

Step 1A: Press and hold the Power button and Volume Down buttons simultaneously and continue holding until the screen starts.

Step 1B: For Android devices with a Home button, press and hold the Home button and the Power button and continue holding until the screen starts.

Step 1C: Press and hold the Power button as well as the Volume Up and Volume Down buttons simultaneously and continue holding until the screen starts.

Step 2: Use the Volume buttons to navigate the choices and select Wipe data/factory reset and confirm your choice with the Power button.

Step 3: Simply wait for the process to complete and wait for your Tecno Spark 10C to restart automatically.

F****or iOS Users

Step 1: For iOS users, meanwhile, tap Settings > General > Transfer or Reset iPhone.

Step 2: Next, choose Erase All Content and Settings. Check the list of items you want to remove.

Step 3: Tap Continue and enter your iPhone passcode. A message warns you that the process will delete all media and data and reset all settings.

Step 4: Tap Erase iPhone to confirm. You’ll be asked to type in your Apple ID and password if Find My is active. Enter your password and tap Erase.

Part 3: How To Fix Black Screen Phone With an Alternative

If your phone screen went black but still works and doing the methods above did not solve the issue, you can use Wondershare Dr.Fone for iOS and Android as a last resort. It’s one of the most popular smartphone repair tools today, enabling you to fix all kinds of annoying scenarios. These include black screen, boot loop, white screen of death, bricked iOS or Android device, and more.

Key Features

Dr.Fone – System Repair for iOS and Android has fantastic features you can immediately take advantage of. Here are its key features below.

• Fix all Android and iOS Problems in Minutes

Dr.Fone – System Repair can fix all kinds of issues on your Android/iOS, such as a black screen, white screen of death, screen freeze, boot loop, or recovery mode. All of this can be done within less than 10 minutes to save you precious time.

• Supports up to 1000+ Android Smartphones and the latest iOS

All iOS versions, including the latest iOS 16 and iOS 16 beta, are fully supported by Dr.Fone – System Repair. The app handles all your smartphone issues without data loss to secure your info. On the other hand, if you own an Android, the app supports up to 1000+ Android smartphones, making it highly versatile for Android owners.

Tech Specs

Dr.Fone – System Repair (Android)’s minimum system requirements for your computer are listed below.

Computer OS	Android
Windows 11, 10, 8.1, 8, 7	Android 2.1 and up to the latest

Meanwhile, here are the system requirements for Dr.Fone – System Repair (iOS).

Computer OS	iOS
Windows 11, 10, 8.1, 8, 7	Supports all iOS versions, including the latest iOS 16 and iOS 16 beta
macOS 12, 11, 10.15, 10.14, 10.13, 10.12, 10.11, 10.10, 10.9, 10.8

Pros and Cons

If you’re still undecided about Dr.Fone – System Repair, here are its pros and cons.

Pros

• Fone – System Repair for iOS and Android has a clutter-free and beginner-friendly user interface. It’s easy to understand and use, so you can start immediately.
• Both the iOS and Android versions finish the repair tasks within less than 10 minutes to save you time.

Cons

• Each version for each OS is sold separately.
• The free version works up to your device’s compatibility. Once you start the repair process, the app will ask you for a valid license key.

How to Fix Black Phone Screen With Dr.Fone – System Repair

Here’s how to fix your phone screen with Dr.Fone – System Repair on iOS/Android.

Step 1: Download and install Dr.Fone – System Repair for iOS or Android. Next, open the program and connect your smartphone.

Step 2A (For iOS): Choose the correct model of your iPhone for the program to be able to download the appropriate firmware package.

Step 2B (For Android): Click Start. On the next window, choose the Brand, Name, Model, Country, and Carrier of your smartphone, then click Next.

Step 3: Follow the on-screen instructions provided on the main program window and wait for the repair process to complete.

safe & secure

4,262,204 people have downloaded it

Conclusion

Our increasing reliance on smartphones has led to amazing advancements in new technologies. However, lingering issues such as your phone screen not turning on or your phone screen being black but still working are ongoing problems to many. That’s why learning how to prevent these events is essential to take care of your smartphone.

Doing all the recommended methods above usually solves the case. If the different fixes don’t work for you, Dr.Fone – System Repair for iOS and Android can help resolve all your problems within less than 10 minutes. You can download it for free on Windows and Mac to test it yourself.

How to Fix the Soft Bricked Tecno Spark 10C?

Bricked phone is a serious problem, as your brick smartphone could be suffering from a soft brick or hard brick problem, and must be dealt with carefully. It is very common to see a brick smartphone these days. If you are wondering what exactly is a bricked phone, here is your answer.

A bricked phone, hard brick or soft brick, is a smartphone which refuses to start or boot all the way up the home/main screen of the Tecno Spark 10C device. This issue is observed within most Android phones because users have a tendency to tamper with the Tecno Spark 10C device settings, flashing new and customized ROMs and tweaking with the essential files. Playing around with the phone’s internal set-up leads to such errors, worst of them being a brick smartphone. Usually, a bricked phone does not switch on and stays frozen at the Tecno Spark 10C device logo, a blank screen or even worse, doesn’t respond to any command, even the power on command.

If you are confused about the soft brick and hard brick problems and looking for solutions to fix your priced phone, then here is all you need to know.

Read on to find out more.

Part 1: What is the difference between soft brick and hard brick?

To begin with, let us understand the basic difference between a soft brick and hard brick issue. Both versions of a bricked phone prevent it from booting but differ in their causes and gravity of the problem.

A soft-brick problem is caused merely by a software error/crash and makes your device switch on automatically every time you manually turn it off. This phenomenon is referred to as Boot Loop. Soft bricked Android phones are not as difficult to fix as the hard bricked Android phones. It is convenient to say that a soft bricked phone only boots up half-way and not fully, whereas a hard bricked device does not switch on at all. A hard brick error is thus caused when the kernel, which is nothing but an interface for the software to communicate with the hardware, is tampered with. A hard bricked phone is not recognized by your PC when plugged in and is a serious problem. It requires troubleshooting techniques and cannot be easily fixed as the soft brick problem.

Hard bricked phones are a rare sight, but the soft brick is very common. Given below are ways to fix a soft brick Android phone. The techniques listed here are the best and the most efficient ways to get your phone back to its normal working conditions without losing your important data or damaging your device or its software.

Part 2: Stuck at the Boot Loop

This is the first sign of a soft bricked Android phone. Boot Loop is nothing but when your phone does not remain switched off and turns itself on automatically, and freezes at the logo screen or blank screen, every time you manually try to power it off.

Stuck at boot loop problem can be fixed by clearing your Cache partitions. These partitions are nothing but storage locations for your modem, kernels, system files, drivers and built-in Apps data.

It is advisable to clear Cache partitions regularly to keep your phone free from such glitches.

Since the phone refuses to boot, Cache can be cleared from entering into the Recovery Mode. Different Android devices have different ways to put it in recovery mode. Normally pressing the power key and volume down key helps, but you may refer to your phone’s guide for better understanding and then follow the steps given below to clear the cache partition:

Once you are the recovery mode screen, you will see a number of options as shown in the screenshot.

Use the volume down key to scroll down and select ”Wipe cache partition” as shown below.

>

After the process is completed, select “Reboot System” which is the first option in the recovery mode screen.

This method will help you erase all the clogged up and unwanted files. You may loose some App related data, but that is a small price to pay to fix your bricked phone.

If this method does not boot up your brick smartphone and the problem still persists, there are two more things you can try. Read ahead to find out about them.

Part 3: Booting straight into recovery mode

If your bricked phone does not boot up to your Home Screen or Lock screen and instead boots directly into Recovery Mode, there is not much left to do. Booting straight into recovery mode is undoubtedly a soft brick error but it also indicates a possible problem with your current ROM. The only option you have to flash a new ROM to reboot your bricked phone back to its normal functioning.

To flash a new ROM:

Firstly, you must root your phone and unlock the Bootloader. Every phone’s mechanism to unlock the bootloader is different, thus, we suggest to refer to your user manual.

Once the Bootloader is unlocked, take a backup of all your data by selecting “Backup” or “Android” back in recovery mode. The process should not take long and all you need to do is tap “OK” to config backup.

In this step, download a ROM of your choice and store it in your SD Card. Insert the SD Card in your phone to begin the flashing process.

Once at the recovery mode, select “Install Zip from SD Card” from the options.

Scroll down using the volume key and use the power key to select the downloaded ROM.

This might take a few minutes of your time, but once the process is complete, reboot your phone.

Hopefully, your bricked phone will not boot normally and work smoothly.

Part 4: Booting straight into Bootloader

If your bricked phone boots straight into Bootloader, then this a serious issue and must not be taken lightly. Flashing a new ROM or clearing cache partitions are of little help in such a brick smartphone situation. Booting straight into Bootloader is a peculiar soft bricked Android phone feature and can be tackled only by downloading and flashing your original ROM from the manufacturer. In order to do so, a detailed study about your manufacturer’s ROM, ways to download and flash must be carried out. Since different Android phones come with different types of ROMs, it difficult to cover all the aspects about the different types of ROMs.

Brick smartphone problem has become more prominent than phone freezing or hanging issue. Android users are often seen looking for solutions to fix their soft brick and hard brick phones. Android phones are prone to get bricked and thus, it is important for us to know about the three techniques given above. These methods have been tried, tested and recommended by ay affected bricked phone users. Therefore, these tips are reliable and worth a try. So if your phone acts stubborn and refuses to boot normally, examine the problem carefully and adopt one of the solutions given above which best suits your situation.