Simple Solutions to Fix Android SystemUI Has Stopped Error For Motorola Edge 40 Pro

In this article, you will learn possible causes of Android SystemUI stopping error and 4 methods to fix this issue. Get Dr.Fone - System Repair (Android) to fix Android SystemUI stopping more easily.

Android SystemUI isn’t responding or Android, unfortunately, the process com.android.systemui has stopped is a not a rare error and is observed in all Android devices these days. The error usually pops up on your device while you are using it with a message on the screen saying Android. Unfortunately, the process com.android.systemui has stopped.

The Android SystemUI isn’t responding error message may also read as “Unfortunately, SystemUI has stopped”.

Android SystemUI error can be very confusing as it leaves affected users with only one option, i.e., “OK”, as shown in the images above. If you click on “OK” you will continue to use your device smoothly, but only until the SystemUI isn’t responding error pops-up on your main screen again. You may restart your device, but the Android SystemUI has stopped the problem continues to annoy you until you find a permanent solution for it.

If you are also among the various users who see Android, unfortunately, the process com.android.systemui has stopped error, then do not worry. SystemUI isn’t responding. Error is not a serious issue and can be tackled easily by carefully examining the reasons behind the problem.

Looking for suitable solutions to fix Android SystemUI has stopped error? Then read on to find out all about Android SystemUI isn’t responding error and the most effective ways to fix it.

Part 1: Why Android SystemUI Has stopped happens?

Android device owners would agree that OS updates are very helpful as they fix the bug problem and improve the overall working of your device. However, sometimes these updates may be infected due to which they do not download and install properly. A corrupted OS update may cause Android; unfortunately, the process com.android.systemui has stopped error. All Android updates are directly designed around the Google App, and thus, the problem will persist until the Google App is also updated. Sometimes, even the Google App update may cause such a glitch if it is not successfully downloaded and installed.

Another reason for the Android SystemUI isn’t responding error to occur, maybe because of flashing a new ROM or due to improper firmware update installation. Even when you restore the backed up data from cloud or your Google Account, such Android, unfortunately, the process com.android.systemui has stopped error may show up.

It is not possible to say for sure which one of the above-mentioned reasons is causing your device to show Android SystemUI is not responding error. But what we can do is move on to fixing the Android SystemUI by following any one of the three methods given the following segments.

Part 2: How to fix “com.android.systemui has stopped” in one click

As we’ve learned that Android system UI isn’t responding issue is primarily because of the Android OS updates not installed properly or were corrupted. Hence, there comes the need for a powerful Android system repair tool that can help you rectify such annoying errors.

To serve the purpose, we would like to introduce, Dr.Fone - System Repair (Android) . It is one of its kind of applications and is highly recommended as it has a proven success rate to resolve almost all Android system issues.

It’s now time to understand how to fix Android ‘unfortunately, the process com.android.systemui has stopped’ or in simple words, Android system UI isn’t responding.

Note: Before we proceed to Android repair, please ensure to make a backup of all your data . This is because the Android repair process may wipe out all the data on your device to fix the Android OS issues.

Phase 1: Connect and prepare your Motorola Edge 40 Pro

Step 1 – Download the Dr.Fone toolkit over your PC. Install it and launch it over. Opt for the “System Repair” tab from the main screen and get your Motorola Edge 40 Pro connected to the PC.

Step 2 – You need to select “Android Repair” from the left panel and then hit the ‘Start’ button.

Step 3 – Next, you need to select the correct information about your device (i.e., brand, name, model, country/region, and carrier details). Check the warning down below and hit “Next”.

Phase 2: Boot Android in ‘Download’ mode to perform the repair.

Step 1 –You’re now required to boot your Android in Download mode. Here’s what you need to do to put your Android in DFU mode.

If your Android has a Home button:

• Turn off your device. Hold down “Volume Down + Home + Power” buttons altogether for about 10seconds. Let go of the buttons afterward and hit the Volume Up to boot in download mode.

In case your Android has no Home button:

• Turn off your device. Hold down “Volume Down + Bixby + Power” buttons altogether for about 10seconds. Let go of the buttons afterward and hit the Volume Up to boot in download mode.

Step 2 – Once done, hit “Next” to initiate the downloading of the firmware.

Step 3 – As soon as the download completes, the Android repair will automatically be started by the program.

Step 4 – In a just a matter of a few minutes, your Android system UI isn’t responding issue will be resolved.

Part 3: Uninstall Google updates to fix Android SystemUI issue

All Android SystemUI isn’t responding errors are circled the Google App as the Android platform is heavily dependent on it. If you have recently updated your Google App and the Android, unfortunately, the process com.android.systemui has stopped error keeps popping up at regular intervals, make sure you uninstall Google App updates as soon as possible.

Follow the steps given below to fix the Android SystemUI has stopped issue by rolling back the Google App updates:

• Visit “Settings” and select “Apps” or “Application Manager”.
• Now swipe to view “All” Apps.
• From the list of Apps, select “Google App”.
• Finally, tap on “Uninstall Updates” as shown hereunder.

Note: To prevent the Android SystemUI isn’t responding error to occur in the future, do not forget to change your Google Play Store settings to “Do Not Auto-Update Apps”.

Part 4: Wipe Cache partition to fix Android SystemUI error

Android, unfortunately, the process com.android.systemui has stopped error can also be fixed by clearing your cache partitions. These partitions are nothing but storage locations for your modem, kernels, system files, drivers, and built-in Apps data.

It is advisable to clear Cache portions regularly to keep your UI clean and free of glitches.

Android SystemUI isn’t responding error can be overcome by clearing the cache in recovery mode.

Different Android devices have different ways to put it in recovery mode. Refer to your device’s manual to enter the recovery mode screen on your device and then follow the steps given below to fix Android; unfortunately, the process com.android.systemui has stopped error by clearing the cache partition:

• Once you are the recovery mode screen, you will see several options as shown in the screenshot.

• Use the volume down key to scroll down and select ”Wipe cache partition” as shown below.

• After the process is completed, select “Reboot System” which is the first option in the recovery mode screen.

This method will help you de-clutter your device and erase all the clogged up unwanted files. You may lose App related data too, but that is a small price to pay to fix the Android SystemUI isn’t responding error.

If the Android SystemUI has stopped the problem persists, there is only one way out. Read on to find out about it.

Part 5: Fix Android SystemUI error by factory reset

Factory Resetting your device to fix Android; unfortunately, the process com.android.systemui has stopped error is a desperate measure and should be the last thing to do on your list. Take this step only when the above mentored two techniques fail to work.

Also, make sure you take a back-up of all your data and contents stored in your Motorola Edge 40 Pro on the cloud, Google Account or an external memory device because once you perform a factory reset on your device, all media, contents, data and other files are wiped out, including your device settings.

Follow the steps given below to factory reset your device to solve the Android SystemUI isn’t responding problem:

• Visit “Settings” by clicking the settings icon as shown below.

• Now select “Backup and Reset”.

• In this step, select “Factory data reset” and then “Reset Device”.
• Finally, tap on “ERASE EVERYTHING” as shown below to Factory Reset your device.

After the factory reset process is completed, your device will automatically restart, and you will have to set it up once again.

The whole process of factory resetting your Motorola Edge 40 Pro might sound tedious, risky, and cumbersome, but it helps to fix the Android SystemUI has stopped error 9 out of 10 times. So, think carefully before using this remedy.

Android SystemUI isn’t responding or Android, unfortunately, the process com.android.systemui has stopped error is commonly seen by users on their devices. It is not a random error and is linked to either the software, Google App, cache partition, or data stored in the Motorola Edge 40 Pro device. It is fairly simple to deal with this issue as all you need to do is install or roll back your Android OS update, uninstall Google App updates, clear cache partition, or factory reset your device to clear all data, files, and settings stored in it. The methods listed and explained above are the best ways to fight the problem and to prevent it from troubling you in the future. These methods have been adopted by affected users all over the world who recommend them because they are safe and involve minimum risks as compared to other tools to solve the Android SystemUI has stopped error. So go ahead and try them now!

Motorola Edge 40 Pro Bootloop Problem, How to Fix it Without Data Loss

Have you, like many other users, faced the bootloop Android problem and wondered what exactly is Android boot loop. Well, Android boot loop is nothing but an error that makes your phone switch on itself every time you manually turn it off. To be precise, when your Motorola Edge 40 Pro does not remain switched off or powered off and starts to boot up automatically after a few seconds, it might be stuck in the boot loop Android.

An Android boot loop is a very common problem and is one of the first symptoms of a soft-bricked device. Also, when your device is experiencing Android boot loop issue, it does not start normally to reach the Home or Locked Screen and remains frozen at the Motorola Edge 40 Pro device’s logo, Recovery Mode or a lit-up screen. Many people fear losing their data and other files due to this error and thus, it is a very confusing situation to be in.

We understand the inconvenience caused, therefore, here are ways to tell you how to fix the bootloop problem in Android devices without losing any important data.

However, before moving on, let us learn a little about the causes for the Android boot loop error.

Part 1: What might cause the bootloop issue on Android?

Android boot loop error might seem weird and unexplainable but it occurs because of some specific reasons.

Firstly, please understand that it is a misnomer that boot loop error occurs only in a rooted device. Boot loop Android error can also occur in a stock device with the original software, ROM, and firmware.

In a rooted device, changes made, such as flashing a new ROM or customized firmware which are not compatible with the Motorola Edge 40 Pro device’s hardware or existing software, can be blamed for the boot loop problem.

Moving on, when your device’s software is unable to communicate with the system files during the start-up process, Android boot loop problem may arise. Such a glitch is caused if you have recently updated the Android version.

Also, corrupt App update files may also cause the bootloop Android issue. Apps and programs downloaded from unknown sources bring in a particular type of virus that prevents you from using your device smoothly.

All-in-all, Android boot loop error is a direct outcome of when you try to tamper with your device’s internal settings.

Hence, if you are looking for ways to guide you about how to fix boot loop issue, you will have to revamp the Motorola Edge 40 Pro device internally by either resetting it or adopting a recovery method.

Read on to know more about how to fix the bootloop error without any data loss when your device suffers from the bootloop Android problem.

Part 2: One click to Fix Android Bootloop without factory reset

If you are trying to figure out how to fix boot loop, the first option you have is the one-click fix to Android Bootloop which involves using the Dr.Fone - System Repair software.

This is designed to repair any data corruption on your device and restores your firmware to its usual working condition.

Dr.Fone - System Repair (Android)

One click to fix boot loop of Android

• #1 Android repair solution from your PC, can fix a wide range of Android system issues, such as boot loop, black screen, etc.
• The software requires no technical expertise, and anybody can use it
• A one-click solution when learning how to fix Android boot loop
• Not require root Android phones.
• Works with most Motorola Edge 40 Pro devices, including the latest Motorola Edge 40 Pro phones like S22
• Simple and easy-to-use user interface

4,689,059 people have downloaded it

To help you get started, here’s a step-by-step guide on how to use Dr.Fone - System Repair.

Note: This method can erase data on your device, including your personal files, so make sure you’ve backed up your device before proceeding.

Step #1 Download the Dr.Fone - System Repair software from the website and install it onto your computer.

Open the software and select the System Repair option from the main menu to fix the Android bootloop error.

Step #2 Connect your Motorola Edge 40 Pro to your computer using the official cable and select the “Android” option from the three menu items. Click “Start” to confirm.

You’ll then need to input the Motorola Edge 40 Pro device information, such as your carrier info, device name, model, and country/region in order to ensure you’re downloading and repairing the correct firmware to your phone.

Step #3 Now you’ll need to put your phone into Download Mode to remove the Android bootloop.

For this, you can simply follow the onscreen instructions for both phones with and without home buttons.

Click “Next”, and the software will begin downloading the firmware repair files.

Step #4 Now you can sit back and watch the magic happen!

Make sure your computer stays connected to the internet, and your device stays connected to your computer throughout the entire process. Once the firmware has been downloaded, it will be automatically installed onto your mobile device, removing the boot loop Android error.

You’ll be notified when the process is done and when you can remove your device and start using free from the boot loop Android error!

safe & secure

Part 3: Soft reset to fix Android bootloop issue

When your device is stuck in Android boot loop, it does not necessarily mean that it is bricked. Boot loop might be occurring due to a simpler problem which can be fixed by turning off your device. This sounds like a home remedy for a serious problem but it works and resolves the problem most of the time.

Follow the steps given below to soft reset your device:

Turn the Motorola Edge 40 Pro device off and take out its battery.

If you cannot take the battery out, let the phone be off for about 3 to 5 minutes, and then turn it back on.

Simply performing a soft reset on your device can help you if you are looking for solutions for how to fix the bootloop issue. This a very useful method as it does not result in any kind of loss in data and protects all your media files, documents, settings, etc.

In case the Motorola Edge 40 Pro device does not turn on normally and is still stuck in the bootloop Android problem, be prepared to use the troubleshooting techniques given and explained below.

Part 4: Boot into Safe Mode to fix Android boot loop

Booting your Motorola Edge 40 Pro into Safe Mode is a useful troubleshooting step to fix boot loop issues caused by third-party apps. When in Safe Mode, the Motorola Edge 40 Pro device will start up with only essential system apps, and any downloaded apps that might be causing conflicts won’t run. Here’s how you can boot your Motorola Edge 40 Pro into Safe Mode to address the boot loop problem:

Step 1: Power Off Your Device

Hold down the power button until it turns off completely.

Step 2: Access Safe Mode

To enter Safe Mode, follow these steps based on your device model:

• For most Android devices: Press and hold the power button to turn on your device. As soon as the manufacturer’s logo appears, press and hold the Volume Down button until the Motorola Edge 40 Pro device finishes booting. You should see “Safe Mode” displayed in the bottom left or right corner of the screen.
• Some devices might require slightly different key combinations. Refer to your device’s user manual or perform an online search for the specific method to enter Safe Mode for your model.

Step 3: Observe the Motorola Edge 40 Pro device

Once your device has booted into Safe Mode, use it for a while to see if the boot loop issue persists. If the boot loop doesn’t occur in Safe Mode, it indicates that the problem is likely caused by a third-party app.

Step 4: Identify and Uninstall Problematic Apps

Now that you’re in Safe Mode, it’s time to identify the troublesome app. Start by uninstalling recently installed apps one by one until the boot loop problem is resolved. After each uninstallation, restart your device normally to check if the boot loop still occurs. Continue this process until you find the problematic app.

Step 5: Restart Normally

Once you’ve identified and uninstalled the problematic app, restart your device normally to exit Safe Mode. Your Android device should now start up without getting stuck in a boot loop.

By following these steps and using Safe Mode to isolate problematic apps, you can effectively troubleshoot and resolve boot loop issues on your Motorola Edge 40 Pro.

Part 4: Factory reset to fix Android bootloop issue

Factory reset, also known as Hard Reset, is a one-stop solution for all your software resulting in issues. Android boot loop being such problem, can be easily overcome by performing a factory reset.

Please note that all your device’s data and settings will be deleted by adopting this method. However, if you have a Google account signed in on your Motorola Edge 40 Pro, you will be able to retrieve most of your data once the Motorola Edge 40 Pro device turns on.

To factory reset your Android boot loop device, you must first boot into the Recovery Mode screen.

To do this:

Press the volume down button and power button together until you see a screen with multiple options before you.

When you are at the Recovery Mode screen, scroll down using the volume down key, and from the options given, select “Factory Reset” using the power key.

Wait for your device to perform the task and then:

Reboot the phone in Recovery Mode by selecting the first option.

This solution is known to fix the boot loop error 9 out of 10 times, but if you still can’t start your Motorola Edge 40 Pro normally, consider using a CWM Recovery to resolve the Android boot loop issue.

Part 5: Use CWM Recovery to fix bootloop on rooted Android

CWM stands for ClockworkMod and it is a very popular custom recovery system. To use this system to solve the boot loop Android error, your Motorola Edge 40 Pro must be rooted with CWM Recovery System which basically means CWM must be downloaded and installed on your device.

Furthermore, to use CWM Recovery to fix boot loop on rooted Android devices, follow the steps given below:

Press the home, power, and volume up buttons to launch the CWM Recovery screen.

Note: you might have to use a different combination of keys to enter into Recovery Mode, depending on your device’s model.

Scroll down using” the volume key to select “Advanced”.

Now select “Wipe” and choose to wipe “Dalvik Cache”.

In this step, select “Mounts and Storage” to click on “Wipe” or “Cache”.

Once this is done, make sure to reboot your Motorola Edge 40 Pro.

This process with successfully fix the Android boot loop error and not cause any loss of data stored on your device stuck in boot loop.

So the bottom line is that boot loop Android issue may seem like an irreparable error but it can be resolved by carefully following the techniques explained above. These methods not only tell you how to fix the bootloop problem but also prevent it from occurring in the future.

An Android boot loop is a common phenomenon with all Android devices because we tend to tamper with our device’s internal settings. Once the ROM, firmware, kernel, etc are damaged or rendered incompatible with the Motorola Edge 40 Pro device’s software, you cannot expect it to function smoothly, hence, the boot loop error occurs. Since you are not the only one suffering from the Android boot loop problem, be rest assured that the ways, given above, to combat it are recommended by users facing similar troubles. So, don’t hesitate and go ahead to try them on.

safe & secure

Reliable User Guide to Fix Motorola Edge 40 Pro Running Slow and Freezing

Android smartphones have opened a lot of doors for their users. They continue to evolve year after year with the hope of giving the world a wonderful digital experience. So far, we can all agree that they’re going the extra mile and doing a really great job. Android phones today are all packed with supreme capabilities that are beneficial to everyone.

However, Android phones are still not close to perfect. They also act up sometimes and cause a stir. Some users have observed that the Android phone is running slow and freezing over time. There can be many potential reasons why Android phone runs slow suddenly. But it doesn’t mean it cannot be restored at all to its original state and function.

In this article, we will review the details of this Android phone issue. We’ll provide solutions you can try if you ever get caught in the same problem. Continue reading to learn more.

Understanding the Specs That Make Android Phones Run Fast

The issue of Android phone running slow and freezing is not limited to old devices only. The same problem has also been observed in newly purchased units. The roots of this unfortunate occurrence vary from one user to another. It depends on different elements, from external factors like users’ handling of the Motorola Edge 40 Pro device to internal factors such as its capabilities. To understand it more, below are some Android phone specifications related to the Motorola Edge 40 Pro device’s overall performance and speed.

The CPU Core Count

Unlike before, Android phones today are equipped with several cores. Each of them has the ability to execute a process alone. Therefore, the Motorola Edge 40 Pro device can handle two or more tasks at once without compromising the quality of its performance. If your Motorola Edge 40 Pro contains more CPU core, its performance surely be more powerful and speedy.

The CPU Clock Speed

Simply put, clock speed is basically the speed at which the CPU cores can carry out a cycle in a second. A faster clock speed definitely translates into the Motorola Edge 40 Pro device’s higher performance. For instance, an octa-core Android phone with a one GHz per second clock speed is a decent device. But it’s less powerful than a device with the same number of cores but runs at two GHz per second.

Random Access Memory

In a simple language, Random Access Memory (RAM) temporarily stores the data from apps that are currently running. Smartphones can be more flexible with multi-tasking if their RAM has enough space. So if you’re among these users who perform multiple tasks simultaneously, you better choose a device with more RAM.

Internal Storage

The mobile applications installed on your smartphones are directly related to internal storage. The apps save their data every time, so they behave strangely when the Motorola Edge 40 Pro device runs out of storage. If you’re using heavy mobile applications, it’s best to opt for smartphones with huge internal storage.

Click here

Reasons Why My Motorola Edge 40 Pro is Running Slow

It’s not really hard to tell why your Motorola Edge 40 Pro is slow because it’s apparently a common issue among users. But don’t worry. Most of the time, the problem is not a major concern. Here are some scenarios that may slow down your Motorola Edge 40 Pros.

Overloading Background Processes

It’s great to have an Android phone that can flawlessly multi-task. However, not all units can handle that well. As mentioned earlier, it depends on the CPU core count and the core’s clock speed. If your Motorola Edge 40 Pro is running slow and freezing, many processes may be happening at the same time. Your device’s cores and clock speed are potentially incapable of executing such demands.

Your Phone is Running Out of Storage

Mobile apps need to save data on your phone. They perform the tasks based on the data stored on the Motorola Edge 40 Pro device. So if your Motorola Edge 40 Pro is slow, it’s possible that your device is already running out of storage. Each app has its own storage requirement. If your phone goes below that, the app will surely crash and not work.

Animation Speed is Way Too Slow

You can modify the Motorola Edge 40 Pro device’s animation type and speed on your Motorola Edge 40 Pro via the developer’s option. However, altering its default settings can sometimes make the Android phone run slow. If the speed is set slower, more delays are added to the animation. Hence, it takes a while for Your Motorola Edge 40 Pro to launch an app or complete a certain process.

You’re Using an Outdated Android Version

If your Motorola Edge 40 Pro is running slow and freezing, the Motorola Edge 40 Pro device’s software is probably outdated. The mobile apps installed on your device are lagging or crashing because they’re no longer compatible with the OS. It happens most of the time. Hence, always watch out for OS updates.

Your Phone is Experiencing Some System Issues

Operating systems and device software serve as the main component of all smartphones. Sometimes, it runs into inevitable problems caused by computer bugs and other glitches. When it happens, the Motorola Edge 40 Pro device’s overall performance is affected. So that can be the reason why sometimes your Motorola Edge 40 Pro is running slow and freezing.

Your Internet Connection is Unstable

Of course, a slow internet connection can make the Android phone runs slow too. Most apps today rely heavily on the internet to execute some tasks like communicating and streaming. So don’t panic when your Motorola Edge 40 Pro is running slow and freezing. It’s possible that your internet connection is messing up with you.

What to Do When My Motorola Edge 40 Pro Lags?

It’s not as bad as the black screen of death when the Android phone runs slow. However, it can still cause some delays and inconvenience for users. So it’s really important to take action when you notice some anomalies with its speed and performance. Below are some remedies that can help you get rid of this issue.

Solution 1: Reboot Your Phone

Sometimes, minor bugs can give your device a hard time. It can be the reason why your Motorola Edge 40 Pro is running slow and freezing. If that’s the case, rebooting your phone might help a lot. Here’s how to do it.

• Step 1: For seven seconds or more, hold the Power and the Volume Down button together.

• Step 2: Several options will manifest on the screen. From there, click Restart. Wait until your device completely shuts off and restarts again.

Solution 2: Uninstall the Unused Apps to Free Up Some Storage

If your Motorola Edge 40 Pro is running slow and freezing, it’s likely because you’re running out of internal storage. You may uninstall the apps you rarely use to free up some space. Here’s how to do it.

• Step 1: On your home screen, find the app you wish to uninstall. Hold its icon until an option list appears.
• Step 2: Click Uninstall.

• Step 3: Click Ok if it asks you to confirm the action.

Wait until the app icon disappears from the home screen.

Solution 3: Set the Animation Speed a Little Faster

Altering the animation speed is not that dangerous. However, it can sometimes interfere with the Motorola Edge 40 Pro device’s smoothness if set too slow. If your Motorola Edge 40 Pro is running slow and freezing after modifying this setting, try to re-adjust it a little faster. Here’s how to do it.

Initiate the following steps first to enable the developers option on your device. Skip this if you have already activated the developers option:

• Step 1: Go to Settings.
• Step 2: Find the About Phone option. Click on it.

• Step 3: Find the Build Number. And then click on it seven times.
• Step 4: Enter your lock screen passcode if necessary.

Follow these steps to adjust the animation speed:

• Step 1: Tap Settings from your home screen.
• Step 2: From the given options, find and click Systems.
• Step 3: Click Developers options.
• Step 4: Under the Drawing section, you’ll find the following animation scale settings: Window Animation Scale, Transition Animation Scale, and Animator Duration Scale. Adjust the speed of these three options to 0.5x.

Solution 4: Update Your Phone to the Latest Android Version

It’s always recommended to update your phone to the latest Android version. Aside from repairs to some system errors, it also keeps your phone compatible with mobile apps. An outdated operating system can be the reason why your Motorola Edge 40 Pro runs slow, and the apps are freezing. Don’t worry. It’s very easy to perform. Here’s how to do it.

• Step 1: First, ensure your internet connection is strong and stable to avoid unwanted interruptions.
• Step 2: Go to Settings.
• Step 3: Click About Phone.
• Step 4: Click Check Now for Update. If there’s new software available, it will automatically appear on the screen.
• Step 5: Click Install Now. Depending on your device, it will restart itself after the installation process.

Solution 5: Reset Your Motorola Edge 40 Pro to Factory Settings

One way to restore the original performance of your Motorola Edge 40 Pro is to revert it back to factory settings. It deletes all the phone’s data and adjusts the settings to default. Most of the time, this procedure works magic. It fixes numerous issues, including the Android phone that’s slow and constantly freezing. But ensure your phone has already been backed up before commencing this step. You may use Wondershare Dr.Fone to help you back up and secure your files.

Here’s how to back up your Motorola Edge 40 Pro using Wondershare Dr.Fone:

• Step 1: Download Wondershare Dr.Fone from its official website. And then install it on your desktop.
• Step 2: Launch the application on your computer.
• Step 3: After it fully loads, connect your Motorola Edge 40 Pro to your computer.
• Step 4: From the main dashboard, find and click Phone Backup. Ensure your device is in USB Debugging mode.

Step 5: Check the files or data you wish to back up. Right after, click Backup.

Here’s how to reset your Motorola Edge 40 Pro to factory settings:

• Step 1: Go to Settings.
• Step 2: Click System.
• Step 3: Click Reset Options.
• Step 4: Click Erase All Data (Factory Reset).
• Step 5: Your Android phone will inform you about the data that will be deleted from this procedure. From there, click Reset Phone.
• Step 6: Your Android device will ask you to confirm the procedure. From there, click Erase Everything.

Solution 6: Fix the System Issue Using Wondershare Dr.Fone

The device’s operating system may sometimes run into unexpected problems. That can make your Motorola Edge 40 Pro performs slow. System issue is not a terrifying scenario at all. Thanks to Wondershare Dr.Fone, which provides instant repair to this kind of mobile problem. Here’s how to use it in easy steps.

• Step 1: Launch the Wondershare Dr.Fone application on your desktop. And then connect your Motorola Edge 40 Pro to your computer.
• Step 2: Click System Repair from the main dashboard or Toolbox section.

Click here

• Step 3: Click Android.

• Step 4: Wondershare Dr.Fone will give you a list of the Android problems that this procedure will fix. From there, click Start.

• Step 5: Wondershare Dr.Fone will ask you to confirm your device details. Review the listed details for Brand, Name, Model, Country, and Carrier. Amend them if necessary. Tick the checkbox beside the Note if you agree to the terms. Lastly, click Next to proceed.

• Step 6: At this point, you need to put your device into Download Mode. Power off your device. And then hold these three buttons altogether: Volume Down, Home (or Bixby if you’re using a newer model), and Power buttons. Finally, press the Volume Up button.

• Step 7: Wondershare Dr.Fone will automatically download the firmware that matches your device’s specifications. Wait until the process has been completed.

• Step 8: Thereafter, the details about the newly downloaded firmware package will be displayed on the screen. From there, click Fix Now.

• Step 9:  Before initiating the installation process, Wondershare Dr.Fone will ask you to review and confirm the firmware details. It will also let you know that this procedure will erase the phone’s data. If you agree to the terms, enter 000000 into the input box and click Confirm.

• Step 10: Wait while Wondershare Dr.Fone installs the new firmware to your device.

• Step 11: A notification will immediately appear after installing the new firmware. Click Done if your phone starts normally. Otherwise, click Try Again to repeat the process.

safe & secure

3,660,347 people have downloaded it

Conclusion

Android phone is capable of performing lots of stuff. It can assist you in both your personal and professional tasks. But if it’s sluggish and doesn’t execute optimally, the good things it promises all go down the drain. So if you notice that your Motorola Edge 40 Pro is running slow and freezing, act fast to resolve the issue. Wondershare Dr.Fone can be of great help in this kind of situation. It’s an all-in-one mobile solution that can assist you with system repair, phone backup, data recovery, and a lot more.

Also read: