[Solved] Warning: Camera Failed on Tecno Spark 20C

In this article, you will learn why camera fails on Tecno Spark 20C devices, how to make camera work again, as well as a system repair tool to fix this issue in few clicks.

Tecno Spark 20C devices are one of the best Android devices available in the market and their users are always satisfied with their features. However, it is a recent observation that many Tecno Spark 20C users complain about Tecno Spark 20C camera failed error while using the camera App on the Tecno Spark 20C device. It is a strange error and pops up suddenly with only one option to tap on, i.e., “OK”

The error message reads as follows: “Warning: Camera Failed”.

Once you click on “OK” the app shuts down abruptly and your Tecno Spark 20C camera is failed. We understand this is not a very pleasing situation, thus, here are ways to tackle the camera failed Tecno Spark 20C issue. Let us now move ahead and find out why exactly you experience Warning: Camera Failed error and how to fix it.

Part 1: Why Tecno Spark 20C phone has Warning: Camera Failed error?

We are all aware that no device runs smoothly, without any glitches. We also know that there is a cause behind every problem. Listed below are a few reasons behind camera failed error, especially on Tecno Spark 20C devices:

1. If you have recently updated your OS version, there are chances that certain bugs are preventing the camera App from functioning normally. Also, if the update is interrupted and not downloaded completely, certain apps may suffer.
2. There are chances of your internal storage being cluttered with unwanted Apps and files leaving no space for the camera App to save its data and work smoothly.
3. If you haven’t cleared camera Cache and Data, the chances of the App to get clogged up increase tremendously which disrupt its working.
4. Warning: Camera Failed error can also be a direct outcome of a change in the system settings or the Tecno Spark 20C device’s internal settings.
5. Finally, if you tamper a lot with the camera settings and do not update the App whenever it is available, Tecno Spark 20C Camera App will not be efficient.

There might be much more reasons for the camera failed error, but these are the most obvious ones. Now let us now move on to troubleshooting the problem.

Part 2: How to fix Tecno Spark 20C Camera Failed in One Click?

If you are experiencing some kind of issues in your Tecno Spark 20Cs such as Tecno Spark 20C camera failed, the Tecno Spark 20C device stopped working, black screen, play store not working, etc. There is a special software is designed for such kind of issues in Android devices, i.e. dr. fone. The tool enables the users to fix various kinds of issues in the Tecno Spark 20C devices and perform a complete system repair so the Tecno Spark 20C device starts working normally.

Dr.Fone - System Repair (Android)

One-click solution to fix camera failed on Tecno Spark 20C devices

• The tool has a one-click operation which makes it super easy to use.
• You don’t need any technical skills expertise to operate the software.
• The software supports all the Tecno Spark 20C devices including the latest and older ones.
• The software can fix the “warning camera failed”, the app is crashing, failed update, etc.

4,616,396 people have downloaded it

Note: You have to remember that the system repair may erase all the Tecno Spark 20C device data. So, create a backup of your Tecno Spark 20C data first and then try fixing the Tecno Spark 20C phone.

Follow the steps given below and fix the camera failed error:

Step 1. Download the software on your computer and launch it. Connect your device and select the System Repair option from the main interface. In the next screen, select Android Repair module.

Step 2. You will have to provide the Tecno Spark 20C device details accurately to ensure that the software provides a precise firmware package to be downloaded. Enter brand, name, model, country, and carrier of your device and agree to the terms and condition.

Step 3. Now put your device in the download mode. The software will provide you with a guide to put the phone in download mode to begin the downloading process.

Step 4. As soon as the firmware is downloaded, the software will automatically initiate the repair process. You will be able to see the ongoing repair.

When the software is done repairing the system, you will be notified. Thus, the Camera failed Tecno Spark 20C error in your phone will be fixed.

Part 3: How to fix Camera Failed error by clearing camera data?

Has anyone ever informed you that it is absolutely necessary to keep clearing camera data every once in a while? Yes, since it deletes all unnecessary data stored in respect of the App and no, it does not mean that all your photos and videos will get deleted. Just follow the steps given below to clear camera data:

1. First, visit “Settings’” on your Tecno Spark 20C device and select “Apps” or Application Manager”.

2. Now a list of all Apps will appear before you. Keep scrolling down until your find “Camera”.

Tap on “Camera” to open the “Camera Info” screen and once you are there, hit “Clear Data” option as shown below.

That’s all, now return to the Home Screen and access the camera again. Hopefully, it will work now.

Part 4: How to fix Camera Failed error by removing third-party Apps?

Another tip to fix Tecno Spark 20C camera failed error is by deleting a few unwanted third-party Apps (recently installed) to free some space in the Tecno Spark 20C device’s internal storage. It is essential to create and keep storage space for the camera App to function smoothly and allow it to store its data as well. Also, if this issue only happens recently, it might be some newly installed Apps causing some glitches with the camera.

Simply, follow the instructions given below to remove Apps from Tecno Spark 20C Devices:

1. Click on the “Settings” icon on the Home Screen and from the options before you, select “Apps”/ “Application Manager”.

2. You will see that a list of downloaded and built-in Apps will open up before you as follows.

3. Now, once you select the App you want to uninstall, the App Info screen will appear. Tap on “Uninstall” option and then tap on “Uninstall” again on the pop-up message.

The App will be removed immediately and its icon will disappear from the Home Screen and you will notice an increase in the storage capacity of your device.

Part 5: How to fix Camera Failed error by wiping Cache Partition?

This method might seem tedious and time-consuming and you may also lose your data and essential settings. However, wiping the Cache Partition only cleans your device system internally and gets rid off any unwanted and trouble making elements causing Warning: Camera Failed error. Follow the step-by-step guide given below to clean Cache Partition smoothly:

1. Firstly, switch off the Tecno Spark 20C device by pressing the power button and tapping on “Power Off” as shown in the screenshot below. Then wait for the lit screen to turn off completely before proceeding further.

2. Now, press and hold the power on/off, home and volume up button simultaneously. Your device will now vibrate. This a signal to let go of the power button (only).

3. Once the Recovery Screen appears, leave all buttons and use the volume down key till you reach “Wipe Cache Partition”.

4. Now, to select the option to use the power on/off button and wait for the process to get over. Once this done, tap on “Reboot system now” and see that your device restarts normally.

You may try to use the camera app once the process completes.

Part 6: How to fix Camera Failed error by Reset Settings?

Resetting the camera settings solves the problem 9 out of 10 times and thus is worth a try.

1. To reset, first, launch the Camera App by tapping on its icon.

2. Then go to Camera “Settings” by tapping on the circular gear like icon.

3. Now look for “Reset Settings” options and click on it.

Once done, go back to the Home Screen and start the camera App again to use it.

Part 7: How to fix Camera Failed error by Factory Reset?

Lastly, if the above-mentioned techniques do not help you in fixing the camera failed error, you can consider performing a Factory Reset. Note: This method will delete all your saved data so it is advised to backup before you start the process.

Here are the steps to factory reset your device to fix “Warning: Camera Failed” Error:

1. Start by visiting “Settings” on your Tecno Spark 20C device on which the camera has failed.

2. Now from the list of options before you, select “Backup and reset” and move ahead.

3. Now you must first select “Factory data reset” and then tap on “Reset Device” as shown in the screenshot below.

4. Finally, you have to click on “Erase Everything” and wait for the Tecno Spark 20C device to reboot itself.

Note: You will have to set up your Tecno Spark 20C device from scratch once it is reset, however, that is a small price to pay to fix your Camera App.

Warning: Camera Failed error is not a rare phenomenon and many users experience it on daily basis. So, there is no need to panic, All you need to do is carefully follow the instructions given above and repair your Camera App yourself. You do not need to seek any technical assistance for the same as the camera failed issue is not difficult to deal with. So go ahead and try these tricks to enjoy using the Camera App on your Tecno Spark 20C devices.

Tecno Spark 20C Bootloop Problem, How to Fix it Without Data Loss

Have you, like many other users, faced the bootloop Android problem and wondered what exactly is Android boot loop. Well, Android boot loop is nothing but an error that makes your phone switch on itself every time you manually turn it off. To be precise, when your Tecno Spark 20C does not remain switched off or powered off and starts to boot up automatically after a few seconds, it might be stuck in the boot loop Android.

An Android boot loop is a very common problem and is one of the first symptoms of a soft-bricked device. Also, when your device is experiencing Android boot loop issue, it does not start normally to reach the Home or Locked Screen and remains frozen at the Tecno Spark 20C device’s logo, Recovery Mode or a lit-up screen. Many people fear losing their data and other files due to this error and thus, it is a very confusing situation to be in.

We understand the inconvenience caused, therefore, here are ways to tell you how to fix the bootloop problem in Android devices without losing any important data.

However, before moving on, let us learn a little about the causes for the Android boot loop error.

Part 1: What might cause the bootloop issue on Android?

Android boot loop error might seem weird and unexplainable but it occurs because of some specific reasons.

Firstly, please understand that it is a misnomer that boot loop error occurs only in a rooted device. Boot loop Android error can also occur in a stock device with the original software, ROM, and firmware.

In a rooted device, changes made, such as flashing a new ROM or customized firmware which are not compatible with the Tecno Spark 20C device’s hardware or existing software, can be blamed for the boot loop problem.

Moving on, when your device’s software is unable to communicate with the system files during the start-up process, Android boot loop problem may arise. Such a glitch is caused if you have recently updated the Android version.

Also, corrupt App update files may also cause the bootloop Android issue. Apps and programs downloaded from unknown sources bring in a particular type of virus that prevents you from using your device smoothly.

All-in-all, Android boot loop error is a direct outcome of when you try to tamper with your device’s internal settings.

Hence, if you are looking for ways to guide you about how to fix boot loop issue, you will have to revamp the Tecno Spark 20C device internally by either resetting it or adopting a recovery method.

Read on to know more about how to fix the bootloop error without any data loss when your device suffers from the bootloop Android problem.

Part 2: One click to Fix Android Bootloop without factory reset

If you are trying to figure out how to fix boot loop, the first option you have is the one-click fix to Android Bootloop which involves using the Dr.Fone - System Repair software.

This is designed to repair any data corruption on your device and restores your firmware to its usual working condition.

Dr.Fone - System Repair (Android)

One click to fix boot loop of Android

• #1 Android repair solution from your PC, can fix a wide range of Android system issues, such as boot loop, black screen, etc.
• The software requires no technical expertise, and anybody can use it
• A one-click solution when learning how to fix Android boot loop
• Not require root Android phones.
• Works with most Tecno Spark 20C devices, including the latest Tecno Spark 20C phones like S22
• Simple and easy-to-use user interface

4,689,059 people have downloaded it

To help you get started, here’s a step-by-step guide on how to use Dr.Fone - System Repair.

Note: This method can erase data on your device, including your personal files, so make sure you’ve backed up your device before proceeding.

Step #1 Download the Dr.Fone - System Repair software from the website and install it onto your computer.

Open the software and select the System Repair option from the main menu to fix the Android bootloop error.

Step #2 Connect your Tecno Spark 20C to your computer using the official cable and select the “Android” option from the three menu items. Click “Start” to confirm.

You’ll then need to input the Tecno Spark 20C device information, such as your carrier info, device name, model, and country/region in order to ensure you’re downloading and repairing the correct firmware to your phone.

Step #3 Now you’ll need to put your phone into Download Mode to remove the Android bootloop.

For this, you can simply follow the onscreen instructions for both phones with and without home buttons.

Click “Next”, and the software will begin downloading the firmware repair files.

Step #4 Now you can sit back and watch the magic happen!

Make sure your computer stays connected to the internet, and your device stays connected to your computer throughout the entire process. Once the firmware has been downloaded, it will be automatically installed onto your mobile device, removing the boot loop Android error.

You’ll be notified when the process is done and when you can remove your device and start using free from the boot loop Android error!

safe & secure

Part 3: Soft reset to fix Android bootloop issue

When your device is stuck in Android boot loop, it does not necessarily mean that it is bricked. Boot loop might be occurring due to a simpler problem which can be fixed by turning off your device. This sounds like a home remedy for a serious problem but it works and resolves the problem most of the time.

Follow the steps given below to soft reset your device:

Turn the Tecno Spark 20C device off and take out its battery.

If you cannot take the battery out, let the phone be off for about 3 to 5 minutes, and then turn it back on.

Simply performing a soft reset on your device can help you if you are looking for solutions for how to fix the bootloop issue. This a very useful method as it does not result in any kind of loss in data and protects all your media files, documents, settings, etc.

In case the Tecno Spark 20C device does not turn on normally and is still stuck in the bootloop Android problem, be prepared to use the troubleshooting techniques given and explained below.

Part 4: Boot into Safe Mode to fix Android boot loop

Booting your Tecno Spark 20C into Safe Mode is a useful troubleshooting step to fix boot loop issues caused by third-party apps. When in Safe Mode, the Tecno Spark 20C device will start up with only essential system apps, and any downloaded apps that might be causing conflicts won’t run. Here’s how you can boot your Tecno Spark 20C into Safe Mode to address the boot loop problem:

Step 1: Power Off Your Device

Hold down the power button until it turns off completely.

Step 2: Access Safe Mode

To enter Safe Mode, follow these steps based on your device model:

• For most Android devices: Press and hold the power button to turn on your device. As soon as the manufacturer’s logo appears, press and hold the Volume Down button until the Tecno Spark 20C device finishes booting. You should see “Safe Mode” displayed in the bottom left or right corner of the screen.
• Some devices might require slightly different key combinations. Refer to your device’s user manual or perform an online search for the specific method to enter Safe Mode for your model.

Step 3: Observe the Tecno Spark 20C device

Once your device has booted into Safe Mode, use it for a while to see if the boot loop issue persists. If the boot loop doesn’t occur in Safe Mode, it indicates that the problem is likely caused by a third-party app.

Step 4: Identify and Uninstall Problematic Apps

Now that you’re in Safe Mode, it’s time to identify the troublesome app. Start by uninstalling recently installed apps one by one until the boot loop problem is resolved. After each uninstallation, restart your device normally to check if the boot loop still occurs. Continue this process until you find the problematic app.

Step 5: Restart Normally

Once you’ve identified and uninstalled the problematic app, restart your device normally to exit Safe Mode. Your Android device should now start up without getting stuck in a boot loop.

By following these steps and using Safe Mode to isolate problematic apps, you can effectively troubleshoot and resolve boot loop issues on your Tecno Spark 20C.

Part 4: Factory reset to fix Android bootloop issue

Factory reset, also known as Hard Reset, is a one-stop solution for all your software resulting in issues. Android boot loop being such problem, can be easily overcome by performing a factory reset.

Please note that all your device’s data and settings will be deleted by adopting this method. However, if you have a Google account signed in on your Tecno Spark 20C, you will be able to retrieve most of your data once the Tecno Spark 20C device turns on.

To factory reset your Android boot loop device, you must first boot into the Recovery Mode screen.

To do this:

Press the volume down button and power button together until you see a screen with multiple options before you.

When you are at the Recovery Mode screen, scroll down using the volume down key, and from the options given, select “Factory Reset” using the power key.

Wait for your device to perform the task and then:

Reboot the phone in Recovery Mode by selecting the first option.

This solution is known to fix the boot loop error 9 out of 10 times, but if you still can’t start your Tecno Spark 20C normally, consider using a CWM Recovery to resolve the Android boot loop issue.

Part 5: Use CWM Recovery to fix bootloop on rooted Android

CWM stands for ClockworkMod and it is a very popular custom recovery system. To use this system to solve the boot loop Android error, your Tecno Spark 20C must be rooted with CWM Recovery System which basically means CWM must be downloaded and installed on your device.

Furthermore, to use CWM Recovery to fix boot loop on rooted Android devices, follow the steps given below:

Press the home, power, and volume up buttons to launch the CWM Recovery screen.

Note: you might have to use a different combination of keys to enter into Recovery Mode, depending on your device’s model.

Scroll down using” the volume key to select “Advanced”.

Now select “Wipe” and choose to wipe “Dalvik Cache”.

In this step, select “Mounts and Storage” to click on “Wipe” or “Cache”.

Once this is done, make sure to reboot your Tecno Spark 20C.

This process with successfully fix the Android boot loop error and not cause any loss of data stored on your device stuck in boot loop.

So the bottom line is that boot loop Android issue may seem like an irreparable error but it can be resolved by carefully following the techniques explained above. These methods not only tell you how to fix the bootloop problem but also prevent it from occurring in the future.

An Android boot loop is a common phenomenon with all Android devices because we tend to tamper with our device’s internal settings. Once the ROM, firmware, kernel, etc are damaged or rendered incompatible with the Tecno Spark 20C device’s software, you cannot expect it to function smoothly, hence, the boot loop error occurs. Since you are not the only one suffering from the Android boot loop problem, be rest assured that the ways, given above, to combat it are recommended by users facing similar troubles. So, don’t hesitate and go ahead to try them on.

safe & secure

Proven Ways to Fix There Was A Problem Parsing the Package on Tecno Spark 20C

Unable to install your favorite Apps from Google Play Store because there was a problem parsing the package?

The Parse Error or there was a problem parsing the package error is very common with Android devices. Android is a versatile platform and, therefore, a very popular OS. It is an open software and allows users to download and use various types of apps from the Play store. Android is also a cheaper alternative as compared to other Operating Software.

Since many of us are well versed with most of the Android devices, parse error, or there is a problem parsing the package is an error is not something new and uncommon.

The error message usually pops up on the Tecno Spark 20C device screen when we try to download and install an App, for example, “There is a problem parsing the package Pokémon Go ”.

The error message which appears reads as follows:

“Parse error: There is a problem parsing the package”.

Android users who have experienced this would know that the parse error leaves us with only one option, i.e., “OK” as shown in the image below.

There was a problem parsing the package may occur due to several reasons, most of which are listed and explained below. Furthermore, there is a list of solutions to choose from to eliminate the “there is a problem parsing the package” error.

Read on to find out more.

Part 1: Reasons for the parsing error

Parse Error, better known as “there was a problem parsing the package” error is very common and normally surfaces when we try to download and install new Apps onto our Android devices from Google Play Store.

The reason for the error message to pop-up are many but none of them can be blamed singularly for the “there is a problem parsing the package” error. Given below is a list of the most probable reasons for Parse Error to stop an App from installing. Examine them carefully before moving on to the solutions to fix the “there was a problem parsing the package” error.

• Updating the OS may cause some disturbances in the manifest files of different Apps leading to Parse Error.

• Sometimes, the APK File, i.e., Android Application Package, gets infected due to improper or incomplete App installation causing “there is a problem parking the package” error.

• When Apps are downloaded and installed from unknown sources, due permission is needed. In the absence of such permission, the chances of the Parse Error to occur increase.

• Certain Apps are not compatible or supported by the latest and updated Android versions.

• Anti-virus and other cleaning Apps are also a major reason for the “there was a problem parsing the package” error.

The causes listed above are not App specific. The Parse Error may occur due to any one or more of these reasons, but what is more important is to try to get rid of the problem.

Let us move on to learn ways to fix the there was a problem parsing the package error.

Part 2: 8 Solutions to fix the parsing error

“There is problem parking the package” error can be dealt with easily if only we do not panic and deliberately follows the steps explained in this segment. Here are 7 of the most reliable and trustworthy methods to fix the Parse Error.

They are easy, user-friendly, and do not take much of your time. So don not waste any more of your time and try them now.

2.1 One Click to Fix ‘There is a Problem Parsing the Package

If you’re still encountering the Parsing error, there may be a problem with the Tecno Spark 20C device data on your device, which means you’ll need to repair it. Luckily, there’s a simple, one-click solution you can follow called Dr.Fone - System Repair .

Dr.Fone - System Repair (Android)

Android repair tool to fix all android system issues in one click

• Simple, clean, and user-friendly interface
• No technical knowledge required
• Easy one-click repair to fix ‘there is a problem parsing the package’ error
• Should repair most parsing problems with apps, like ‘there is a problem parsing the package Pokemon Go’ error
• Supports most Tecno Spark 20C devices and all the latest models like Galaxy S9/S8/Note 8

3981454 people have downloaded it

If this sounds like the solution you’re looking for, here’s a step by guide on how to use it yourself;

Note: Please note that this repair process can erase all data on your phone, including your personal information. This is why it’s so important to back up your Tecno Spark 20C before proceeding.

Step #1 Head over to the Dr.Fone website and download the software. Install the downloaded software and open it. From the main menu, select the System Repair option.

Input your device and firmware information to confirm you’re installing the right version of the operating system.

Step #2 Follow the onscreen instructions on how to get into Download Mode to start the Repair process.

Once complete, the firmware will start downloading.

Step #3 Once the firmware has downloaded, it will automatically install it to your device.

When this is completed, you’ll be free to disconnect your Tecno Spark 20C and use it how you please without the ‘there is a problem with the parsing package’ error.

2.2 Allow installation from unknown sources

When we install Apps from other sources and not Google Play Store, there might be a glitch in using such Apps. To overcome this problem, turn on “Allow App installation from other sources”. Follow the steps given below for better understanding:

• Visit “Settings” and select “Applications”.

• Now tick mark on the option saying allow App installation from unknown sources.

2.3 Enable USB debugging

USB debugging is not considered necessary by many users but these methods give you an edge over others while using an Android device as it lets you access things on your phone, etc which you could not earlier.

To enable USB Debugging to fix “There is a problem parsing the package” error, follow these steps:

• Visit “Settings” and select “About Device”.

• Now click on “Build Number” not once but continuously for seven times.

• Once you see a pop-up saying “You are now a developer”, go back to “Settings”.

• In this step, select “Developer Options” and turn on “USB Debugging”.

This should solve the problem. If not, move on to the other techniques.

2.4 Check APK File

An incomplete and irregular App installation may cause the .apk file to get corrupted. Make sure you download the file completely. If need be, delete the existing App or its .apk file and reinstall it from Google Play Store for it to be compatible with your device’s software and to use the App smoothly.

2.5 Check App Manifest File

Manifested App files are nothing but .apk files which are improvised by you. Such changes may cause the Parse Error to occur more frequently. Modifications in the App file can be made by changing its name, App settings, or more advanced customizations. Make sure you roll back all changes and restore the App file to its original state to prevent it from getting corrupted.

2.6 Disable Antivirus and other cleaner Apps

Antivirus software and other cleaning Apps are very helpful in blocking unwanted and harmful Apps from damaging your device. However, sometimes such Apps also prevent you from using other safe Apps.

We do not suggest that you delete the Antivirus App permanently. Temporary uninstallation will be useful here. To do so:

• Visit “Settings” and then select “Apps”.

• Select the antivirus App to click on “Uninstall” and then tap “OK”.

Now download and install the desired App again. Once this is done, do not forget to install the Antivirus App again.

2.7 Clear Cache cookies of Play Store

Clearing Play Store Cache cleans the Android Market platform by deleting all clogged up unwanted data. Follow the steps given below to delete Play Store cache:

• Tap on Google Play Store App.

• Now visit Play Store’s “Settings”.

• Select “General Settings” to “Clear local search history”.

2.8 Factory Reset Android

Factory Resetting your device to fix the Parse Error should be the last thing you try. Make sure you take a back-up of all your data on your Google Account or a Pen Drive because this technique erases all media, contents, data, and other files, including your device settings.

Follow the steps given below to factory reset your device:

• Visit “Settings”.

• Now select “Backup and Reset”.

• In this step, select “Factory data reset” and then “Reset Device” to confirm Factory Reset.

The whole process of factory resetting your Tecno Spark 20C might sound tedious, risky, and cumbersome but it helps to fix the Android SystemUI has stopped error 9 out of 10 times. So, think carefully before using this remedy.

Parse Error: There was a problem parsing the package is an error message that has troubled many Android users. The good part is that the above-stated fixes not only solve the problem but also prevent it from occurring in the future. So, keep them in mind the next time you or anyone you know faces such an issue.