Stuck at Android System Recovery Of Lava Blaze Curve 5G ? Fix It Easily

In this article, you will learn what is Android system recovery, and how to fix Android stuck at system recovery step by step. To get out of Android system recovery more easily, you need this Android repair tool.

You know your Lava Blaze Curve 5G is stuck in recovery mode when you cannot turn on the Lava Blaze Curve 5G device. If you try to turn it on, it shows a message that says, “Android System Recover.” This situation can be quite debilitating for most Android users. Most of the time, you don’t know whether you have lost all of your important Android data. It is even more worrying because of the fact that you cannot turn on your device at all, especially when you don’t know how to fix it.

Part 1. What is Android System Recovery?

Despite all the worry that surrounds an unwanted Android system recovery screen, it is actually a feature that can be quite helpful to your Lava Blaze Curve 5G when it’s needed. It can be useful when you want to hard reset the Android device without having to access the settings. This can be very useful if your device is not working very well or if your touch screen is experiencing problems. It can also be very helpful when you are having a problem accessing the settings on your device.

For these reasons, it is actually a good thing, although when it does happen unexpectedly, you may want to know how to fix it.

Part 2. How to get to Android System recovery

Now that you know how useful the Android System can be, you may want to know how to utilize this feature to get out of some of the problems we mentioned above. Here’s how you can safely get to the Android recovery system on your Lava Blaze Curve 5G.

Step 1: Hold down the power key and then select “Power Off” from the options on the screen. If, however, your screen is unresponsive, keep holding the power key for several seconds until the Lava Blaze Curve 5G device is completely turned off.

Step 2: Next, you need to hold down the Power and the Volume Key. You should able to see the Android image and a bunch of information about your device. There should also be a “Start” at the top right corner of the screen.

Step 3: Press the Volume up and Volume down keys and use the Power key to select menu options. Press the Volume down key twice to see “Recovery Mode” in red at the top of the screen. Press the Power key to select it.

Step 4: The white Google logo will appear immediately followed by the Android logo again as well as the words “No Command” at the bottom of the screen.

Step 5: Finally, press and hold both the Power and the Volume up Key for around 3 seconds and then let go of the Volume up Key but keep holding the Power Key. You should see the Android system recovery options at the top of the screen. Use the Volume keys to highlight and the Power key to select the one you want.

Part 3. Android Stuck at System Recovery? How to fix in one click?

Sometimes during the System Recovery process, the process can glitch, and you’ll lose data on your device, rendering it unusable. However, another solution to fix this is to repair your device using the Dr.Fone - System Repair tool.

Dr.Fone - System Repair (Android)

One-stop solution to fix Android stuck at System recovery

• It’s the #1 software for PC-based Android repair
• It’s easy to use with no technical experience required
• Supports all latest Lava Blaze Curve 5G devices
• Easy, one-click fix Android stuck at system recovery

3981454 people have downloaded it

Here’s a step by step guide on how to use it yourself;

Note: Be aware that this process can erase all your personal files on your device, so ensure you’ve backed up your Lava Blaze Curve 5G before continuing.

Step #1 Head over to the Dr.Fone website and download the software for your Windows computer.

Once installed on your computer, open onto the main menu and connect your Lava Blaze Curve 5G using the official USB cable. Select the System Repair option.

Step #2 Select the ‘Android Repair’ option from the next screen.

Insert your device information, including the brand, carrier details, model and country and region you’re in to ensure you’re downloading the correct firmware.

Step #3 Follow the onscreen instructions on how to put your device in Download Mode.

Your device should already be in this mode but follow the instructions to make sure. There are methods available for devices, both with and without home buttons.

Step #4 The firmware will now start downloading. You’ll be able to track this process in the window.

Ensure your device, and your computer stays connected the entire time, and make sure your internet connection remains stable.

After downloading, the software will automatically start to repair your device by installing the firmware. Again, you can track the progress of this on the screen, and you’ll need to ensure your device remains connected throughout.

You’ll be notified when the operation is complete and when you’re able to disconnect your phone and use it as normal, free from it being stuck on the Android system recovery screen!

Part 4. Android Stuck at System Recovery? How to fix in a common way?

If, however, your device is stuck on system recovery mode, here’s how you can easily get it out of system recovery. The process is slightly different for different Android devices, so you should check your device’s manual before attempting this process.

Step 1: Power off the Lava Blaze Curve 5G device, and just to be sure, take out the battery to ensure that the Lava Blaze Curve 5G device is fully turned off. Then reinsert the battery.

Step 2: Press and hold down the Home button, Power Button, and the Volume up Key simultaneously until the Lava Blaze Curve 5G device vibrates.

Step 3: Once you feel the vibration, release the power button but continue to hold down the Home and Volume up Key. The Android recovery screen will display. Release the Volume up and Home buttons.

Step 4: Press the Volume down key to select the “Wipe Data/ Factory Reset option and then press the Power button to select it.

Step 5: Next, you need to press the Volume down button to highlight “Delete All User Data” and then press the Power button to select it. The device will reset and present the “Reboot System Now” option.

Step 6: Finally, press the Power button to reboot the phone in normal mode.

Part 5. Backup and Restore Android System

Losing data on your Lava Blaze Curve 5G is a common occurrence, and since Android devices don’t really have an automatic full backup solution, it is important to know how to backup and restore your device system. Here’s how to easily do that.

Step 1: Enter the recovery mode on your Lava Blaze Curve 5G, as described in Part 2 above. Use the Volume and Power keys to select the “Backup & Restore” option on the screen.

Step 2: Tap on the backup option or use the Volume and Power keys if your screen is unresponsive. This will begin backing up your system to the SD card.

Step 3: After the process is complete, choose “Reboot” to restart the Lava Blaze Curve 5G device.

Step 4: You can then simply check Recovery > backup directory on your SD card. You can rename it to easily find it later during the restore process.

To restore the system from the backup created, follow these simple steps.

Step 1: Once again, enter recovery mode as described in part 2 above and then choose Backup & Restore from the menu list.

Step 2: Press “Restore” to begin the recovery process from the Backup file we created

Step 3: You will be notified when the system restore is complete.

Android system recovery mode can be quite useful, especially when your system is unresponsive. As we have also seen, it is important to know how to get into and out of System Recovery mode if you are going to backup and restore your Android system. It is also quite easy to do both of these things.

8 Workable Fixes to the SIM not provisioned MM#2 Error on Lava Blaze Curve 5G

SIM cards are small chips that act as a connecting medium between your cell phone and your carrier. It is programmed to help your carrier identify your cell phone account with certain information. And eventually, you are enabled to make calls and to make use of mobile internet. Now, if your device is showing “SIM not provisioned” on Android then it signifies that the connection to carrier network cannot be established or perhaps, your carrier isn’t able to identify your cell phone account.

Part 1. Why does the error “SIM not provisioned MM#2” pop up?

There can be numerous reasons behind the pop up that reads “SIM not provisioned” on Android. But basically, it most probably affects the users who have registered a new SIM card. If you get to experience this issue in other situations or if the SIM is not working in Android, then the problem is with the SIM card and needs to be replaced. Anyways, here is a list of situations when the “SIM not provisioned” error may bother you.

• You got a new SIM card for your new phone.
• You are transferring your contacts into the new SIM card.
• In case, the carrier network provider’s authorization server is unavailable.
• Perhaps, you’re out of the reach of the carrier coverage area and that too, without active roaming agreement.
• Though new SIM cards work flawlessly. But it is often necessary to get your SIM card activated due to security reasons.

Just in case, you haven’t bought any new SIM card and the one you were using was working fine until now, then the most probable reasons behind it could be listed below:

• If your SIM card is too old, possibly it might have gone dead, try replacing it.
• Perhaps, the SIM card was not properly inserted into the slot or there might be some dirt between the SIM and smartphone pins.

A yet another reason could be that your SIM card got deactivated by your carrier provider as it could have been locked to a particular phone. Now, if you insert such a SIM card to another device or a new device even, you may get to witness a message that reads “SIM not valid”.

2.1 One click to fix the “SIM not provisioned MM#2” error on Android

Without talking any further, let’s straightly get to the first and the easiest way to repair SIM not provisioned issue on Android. For this purpose, we’re glad to introduce Dr.Fone - System Repair (Android) , one of its kind of tool that is capable of repairing almost all sort of Android OS issues in just a matter of few clicks. Whether it is SIM not provisioned on Android or SIM not working in Android or your device stuck in a boot loop or black/white screen of death. The most probable reason for these errors is Android OS corruption. And with Dr.Fone – Repair (Android) you can efficiently and effectively repair your Android OS in a hassle freeway.

Dr.Fone - System Repair (Android)

Android repair tool to fix “SIM not provisioned MM#2” error

• Fix any type of Android system issue with ease.
• Even novice users can use it without any hassle.
• Compatible with all major Lava Blaze Curve 5G smartphone models.
• Highest success rate in the market for fixing Android issues.
• Supports all Android OS versions.

3981454 people have downloaded it

Step by step Tutorial to fix “SIM not provisioned MM#2” error

Step 1. Connect your Lava Blaze Curve 5G

Download and launch the Dr.Fone toolkit on your computer and then opt for the “System Repair” option from the main interface. Meanwhile, get your Lava Blaze Curve 5G connected with the computer using a genuine cable.

Step 2. Opt for Android Repair and key in important information

Now, hit on the “Android Repair” from the 3 options on the left, followed by hitting the “Start” button. From the upcoming screen, you’ll be asked to key in important device-related information, like brand, model, country, and carrier details. Hit “Next” afterward.

Step 3. Boot your device in Download mode

You must put your device in Download mode for better repairing of your Android OS. Simply follow the onscreen guide to boot your Android in DFU mode and hit “Next” thereafter. Once done, the software will automatically start downloading the most compatible and recent firmware for your device.

Step 4. Initiate Repairing

As soon as the download completes, the software verifies the firmware and automatically initiates repairing your Lava Blaze Curve 5G. Within a short period, you’ll notice that your Lava Blaze Curve 5G has been successfully repaired.

safe & secure

2.2 Ensure the SIM card is not dirty or wet

At times, the issue can be as simple as cleaning your SIM card and SIM slot properly. Ensuring that SIM is not wet either and then putting it back into its place. If this works, then the SIM not working in Android was due to the dirt or moisture that was preventing proper contact between SIM card pins and smartphone circuit.

2.3 Insert the SIM card correctly

If your SIM card was working properly until yet, there is a good possibility that the SIM card may have moved a bit from its actual location. Eventually, there is poor contact between the SIM card pins and the circuit. Try inserting your SIM card properly with the following steps.

• Power off your Lava Blaze Curve 5G and with the help of Q pin, eject the SIM card holder from the SIM slot of your device.
• Now, grab a soft rubber pencil eraser and gently rub it in on the gold pins of SIM card to clean them properly. Then, with the help of a soft cloth wipe away the rubber residue from the SIM card.
• Next, push the SIM back into the SIM card holder properly and push it back into the SIM slot now.
• Turn your device back on and look if your SIM not provisioned on the Android issue is resolved or not.

2.4 Activate the SIM card

Usually, when you buy a new SIM card, it gets automatically activated within 24 hours of being plugged into a new device. But if that’s not happening in your case and you’re wondering how to activate SIM card, make use of the three options below to enable activation:

• Call your carrier service provider
• Send an SMS
• Log on to your carrier’s website and look for the activation page over it.

Note: The aforementioned options are straightforward and are quick ways to enable activation. It depends on your carrier network whether they support them.

2.5 Contact your carrier

Even if your SIM isn’t activated, grab another working device to make a phone call to your carrier or network. Ensure, to explain the entire situation and the error message to them. Be patient while they investigate the issue. It may eat up a heck load of time or may get resolved in a few minutes that completely depend upon the complexity of the issue.

2.6 Try the other SIM card slot

A yet another reason why SIM not working in Android can be because of the SIM card slot might have gone corrupted. Thanks to the dual SIM technology, you do not have to rush immediately to get it to check or repair. You can simply rule out this possibility by ejecting the SIM card from its original SIM slot and then replacing it into the other SIM card slot. If this solution did work out for you then it is obvious that the problem was with the SIM card slot that got corrupted. And hence, it was triggering SIM not responding issue.

2.7 Try the SIM card in other phones

Or just in case, you’ve still no joy and the SIM not provisioned on Android message is bothering you. Try making use of another Android device. Eject the SIM card from the Lava Blaze Curve 5G device which is creating problems and try plugging it into other Lava Blaze Curve 5G] and other smartphones. Perhaps, this will let you know whether the issue is with your device only or with the SIM card itself.

2.8 Try a new SIM card

Still, wondering how to fix SIM not provisioned? Perhaps, nothing worked for you, right? Well, on that note, you must head to your carrier store and request a new SIM card. Also, inform them about the “SIM not provisioned MM2” error, they will be able to execute proper diagnostics over your old SIM card and hopefully get it resolved. Or else, they’ll equip you with a brand new SIM card and swap the new SIM card into your device and get it activated in the meantime. Eventually, restoring the normal functioning of your device.

Conclusion

In wrapping up, SIM not provisioned errors on Android can be troubling, but they’re certainly fixable. There are several methods, from a simple device restart to reaching out to your network provider. But if these don’t work, we suggest trying Dr.Fone - System Repair (Android) . This tool is known for its ability to handle an array of Android issues and could be just what your device needs. Navigate your tech challenges with ease using Dr.Fone.

safe & secure

11 Ways to Fix it When My Lava Blaze Curve 5G Won’t Charge

What would you do if your phone or other device’s battery is draining? You will plug it into a power source. Right? What if you realize that your phone won’t charge? My phone won’t charge, and the Lava Blaze Curve 5G tablet won’t charge is a common problem.

Android devices are very prone to this problem, and hence Android device owners complain frequently that My Lava Blaze Curve 5G won’t charge even when it is plugged into a power source properly. The reason behind the phone won’t charge, or Lava Blaze Curve 5G tablet won’t charge are not very complicated and, therefore, can be dealt with by you sitting at home.

A charging problem can occur due to a temporary software crash. It is also possible that a corrupted device cache may be causing such a glitch. Another reason for phones not to charge normally or charge slowly is an inappropriate power source or defective charging cable and adapter. All these and many more problems will be cured in the 10 solutions to fix My Lava Blaze Curve 5G won’t charge error.

So if you’re still thinking about why won’t My Lava Blaze Curve 5G charge, read on to find out solutions to fix My Lava Blaze Curve 5G won’t charge problem.

Part 1. One-click solution to fix Android phone won’t charge

While you are upset over ‘why My Lava Blaze Curve 5G won’t charge?’, would you mind us helping you around?

Well, we have got Dr.Fone - System Repair (Android) at your fingertips to get rid of this annoying phone won’t charge issues (caused by system corruption). Whether the Lava Blaze Curve 5G device froze or became unresponsive, bricked, or got stuck on the Lava Blaze Curve 5G logo/blue screen of death or apps started crashing. It can fix every Android system problem.

Dr.Fone - System Repair (Android)

Easy-to-operate program to fix Android phone won’t charge

• As it supports all the latest Lava Blaze Curve 5G devices, it can even easily fix the Lava Blaze Curve 5G tablet won’t charge issue.
• With a single click, you can fix your entire Android system issues.
• The very first tool is available in the market for Android system repair.
• Without any technical knowledge, one can use this software.
• This tool is intuitive with a high success rate.

3981454 people have downloaded it

Note: When you are stressed over ‘why won’t My Lava Blaze Curve 5G charge’, we are ready to eliminate the tension and make things easier for you. But, before you start fixing the phone won’t charge the problem, make sure to back up the Android device . This fixing process might wipe out all the Lava Blaze Curve 5G device data.

Phase 1: Preparing and connecting the Android device

Step 1: Install and then run Dr.Fone - System Repair (Android), the ultimate Android repair software on your PC. Hit the ‘System Repair’ tab, followed by connecting your Lava Blaze Curve 5G.

Step 2: Tap on the ‘Android Repair’ option and then click ‘Start’ for moving ahead.

Step 3: Mention the detailed information about your Lava Blaze Curve 5G under the Lava Blaze Curve 5G device information section. Press ‘Next’ then on.

Phase 2: Get to ‘Download’ mode for repairing the Lava Blaze Curve 5G device

Step 1: It’s essential that you put the Android device under ‘Download’ mode to resolve the phone won’t charge the issue. Here comes how to do –

• With a ‘Home’ button device, switch off it before holding down the set of keys, including ‘Power’, ‘Volume Down’, and ‘Home’ key for 5-10 seconds. Let them go and hit the ‘Volume Up’ key for entering the ‘Download’ mode.

• If the ‘Home’ button is not there, you got to turn down the Lava Blaze Curve 5G device and altogether hold down the ‘Volume Down’, ‘Bixby’, and ‘Power’ keys between 5-10 seconds. Soon after you release the keys, tap the ‘Volume Up’ button for entering the ‘Download’ mode.

Step 2: Click ‘Next’ to start downloading the Android firmware.

Step 3: Now, Dr.Fone - System Repair (Android) would verify the firmware and then start repairing the Android system on its own. It will ultimately fix your ‘why won’t My Lava Blaze Curve 5G charge’ trouble.

Part 2. 10 common ways to fix Android won’t charge

1. Check/replace charging cable

Charging cables fray or become defunct after prolonged usage. Therefore, it is advised to always use the Lava Blaze Curve 5G device’s original charging cable or purchase a good quality charging cord, which doesn’t damage your device or your adapter.

It is also very commonly observed that the charging end of the cable which gets connected to the charging port of the Lava Blaze Curve 5G device gets damaged and prevents the current from flowing to the phone/tablet.

2. Check/clean charging port

The charging port in your device is a small opening where the charging end of the cabbie is inserted for the current to flow to the phone/tablet. Very often, we notice that the charging port gets blocked with tiny particles of dirt. The charging port might also get clogged if dirt and dust get accumulated in it, preventing the sensors from receiving and forwarding the current to the Lava Blaze Curve 5G device.

The best way to take this problem is to clean the port with a blunt pin or a soft bristle unused toothbrush. Make sure you clean the port gently and do not damage it or its sensors.

3. Check/replace charging adapter

This method is fairly simple, and all you need to do is check whether or not the charging adapter is working properly as sometimes, the adapter itself is to be blamed for the charge. To make sure that you are not using a defective adapter, connect your charging cable/USB to another adapter. If your device charges normally, it means there is a problem is with your adapter, and you must replace it at the earliest to solve My Lava Blaze Curve 5G won’t charge the issue.

4. Try another power source

This technique is more like a quick trick. It means to switch from one power source to another or use a more efficient and suitable power source. Laptops and PCs charge slower than a direct power source, i.e., a wall socket. Sometimes, the charging speed is slower, and the battery is draining. In such a scenario, choose to charge your device by directly plugging it into a socket on the wall to never experience My Lava Blaze Curve 5G won’t charge problem.

5. Clear device Cache

Clearing Cache is a great technique as it cleans your device and all its partitions. By clearing the cache, all the unwanted data and files stored in your device get deleted, which may be causing glitches in the Lava Blaze Curve 5G device’s software, preventing it from recognizing the current.

Follow the steps given below to clear your device’s cache:

• Visit “Settings” and find “Storage”

• Now tap on “Cached Data”.

• Click “OK” to clear all unwanted cache from your device as shown above.

Try charging your phone after clearing the cache. If your phone doesn’t charge even now, do not worry. There are more ways to help you combat My Lava Blaze Curve 5G won’t charge problem.

6. Re-start/reboot your phone/tablet

Restarting your device to fix why won’t My Lava Blaze Curve 5G charge error is a very effective remedy. This method of rebooting your device not only fixes software glitches but other but also tackles other factors/operations that might be running in the background preventing your device from charging.

Restarting a device is simple and can be done by following the steps given below:

• Long press the power button of your device.

• From the options that appear, click on “Restart”/ “Reboot” as shown in the image below.

To restart your device, you may also press the power button for about 20-25 seconds for the phone/tablet to automatically reboot.

7. Download and install the Ampere App

The Ampere app can be downloaded from the Google Play Store. It is very helpful to fix the why won’t my charge error as it gives you real-time information about your device’s battery consumption, charging status, and other essential data.

If the App gives information in green color, it means all is wetland your device is charging normally, however, if the information before you is in orange, you need to take steps to fix the charging problem.

8. Install software updates

Installing your Android version updates is a good idea as the software is the interface that receives charge from the charging port sensors and gives a command for the phone/tablet to charge. People often continue to use older OS versions, which cause trouble and prevent the Lava Blaze Curve 5G device from charging.

To check for and install updates on your device, you must be connected to WiFi or a cellular network. Next, visit “Settings” and select “About device”. Now click on “Software Update”.

If there is an update available, you will be prompted to download it. Just follow the instructions given before you install a brand new Android OS version on your device.

9. Factory reset your device

Factory Reset is must be done after due deliberation. Remember to take a back-up of all your data and contents on the cloud or an external memory device, such as a pen drive before adopting this method because once you perform a factory reset on your device, all media, contents, data and other files are wiped out, including your device settings.

Follow the steps given below to factory reset your device:

• Visit “Settings” by clicking the settings icon as shown below.

Click here

• Now select “Backup and Reset” and move on.

• In this step, select “Factory data reset” and then “Reset Device”.

• Finally, tap on “ERASE EVERYTHING” as shown below to Factory Reset your device.

Note: Once the factory reset process is complete, your device will automatically restart and you will have to set it up once again.

10. Replace your battery

This should be your last resort to fix My Lava Blaze Curve 5G won’t charge problem, and you should only attempt to replace your battery if none of the other techniques work. Also, please consult a technician before purchasing and installing a new battery in your device as different phones and tablets have a different type of battery requirements.

Finally, fixing the phone won’t charge the problem is simple, and therefore there is no need for you to worry as you are not the only one experiencing such an issue. Other Android users have tried, tested, and recommended the methods given above to solve why won’t My Lava Blaze Curve 5G charge or Lava Blaze Curve 5G tablet won’t charge error. So go ahead and try them out now.

Also read: